Weber Summit 460-LPG User manual

56861 04/28/11 LPG
AU - AUSTRALIA
#56861
460 - LPG
660 - LPG
GAS GRILL
Built-In LPG Gas Grill Installation Guide



m

 
 
 
 





m
 

 


m 








m 



WWW.WebeR.com®3
bUILT-IN cUToUT DImeNSIoNS

There are several configuration options for the grill and gas supply access of your Island
structure.
The 3 common options (A, B, C) are illustrated in the “ ‘Island’ Structure Configuration
Options” table. ◆

All dimensions are to finished surfaces.
m 
◆
bUILT-IN cUToUT GeNeRAL DImeNSIoNS
1
2
3
460 660 ToLeRANceS
134" (864 mm) 42" (1067 mm) ±1/4" (6 mm)
36" (914 mm) 36" (914 mm) max
324 5/16" (618 mm) 24 5/16" (618 mm) ±1/4" (6 mm)
cLeARANceS
1
2
1 1
124" (610 mm) any surface
27" (686 mm) minimum for lid clearance

When determining a suitable location for your Summit®gas grill installation, give
attention to concerns such as exposure to wind, proximity to traffic paths, and keeping
any gas supply lines as short as possible. Never locate the Summit®gas grill in a
garage, breezeway, shed, under an unprotected overhang, or other enclosed area.
Locate the grill and structure so there is enough room to safely evacuate the area in
case of a fire.

m 



m 


NOTE: If you have questions on what materials are considered noncombustible, contact
your local building materials supplier or fire department. ◆
“ISLAND” STRUcTURe coNFIGURATIoN oPTIoN
1
2
2
2
1
1
CB
A
1Summit®4-burner/6-burner grill
Gas supply

4
bUILT-IN cUToUT DImeNSIoNS

The Summit®Built-In unit should be on site before construction begins.
For ease of installation, the grill will be pushed on its casters into the built-in structure.
The installation of this grill requires a level floor pad surface  and countertop surface.
The floor pad surface must be constructed from solid materials and must be level
and smooth. Proper subgrade materials must be used under the floor pad to prevent
materials from settling and heaving.

If the supporting structure is going to have an electrical outlet for a rotisserie, it should
be on the left side of the structure. ◆
1



bUILT-IN cUToUT DeTAILeD DImeNSIoNS
2
3
5
6
7
a
b
c
b
12
3
1
1
460 660
DImeNSIoNS
124" minimum* (610 mm) 24" minimum* (610 mm)
16 1/2" (419 mm) 16 1/2" (419 mm)
311 1/8" (283 mm) 11 1/8" (283 mm)
410 1/2" (267 mm) minimum 10 1/2" (267 mm) minimum
24 5/16" (618 mm) 24 5/16" (618 mm)
36" (914 mm) maximum 36" (914 mm) maximum
734" (864 mm) Built-In frame 42" (1067 mm) Built-In frame
For a countertop treatment: recommended 3/4" (19 mm) overhang.
bGas inlet
Access for electric on left hand side

WWW.WebeR.com®27

A 58" (147.32 cm) corrugated gas line is connected to the manifold of the grill.
A) The main corrugated line passes through the “Island Structure” cavity to the hose
and regulator connection inside the tank enclosure .
B) Uncap the flare fitting from the 90° Connection on the regulator hose located inside
the tank enclosure .
C) Connect the main corrugated hose to the 90° bulkhead fitting. Use the 1/2" (12.7
mm) flared gasket to ensure proper seal .
Note: 1/2" flared gaskets are included in the Summit® Built-In tank Enclosure Kit
included with your grill. ◆
coNNecTIoN cHART
1
2
3
4
5
6
7
8
9
10
4Typical tank cabinet or tank enclosure location
Side view
Top of box
7Back of box
Corrugated gas line to manifold
90° fitting
10 1/2" (13 mm) flared gasket
bUILT-IN TANK eNcLoSURe PARTS LIST / ASSembLY

28

m 


Ventilation holes can be located in a low visibility area and should be protected by
screening material to prevent rodents and insects from entering the structure. Air holes
will also help dry moisture.
Note:These drawings are only a reference.
• Crossventilationmustbeincorporatedinthesupportingstructure.Werecommenda
minimum of 100 square inches (254 square cm) of venting per side.
• Ventsshouldbeontwosidesofthestructure.
• Thedrawingsareforreferenceonly.
• Locationoftheventsshouldbefromthecenter,outward.
• Locatetheventsatboththebottomofthestructureandatthetopofthestructure.
• Thebottomventsshouldbeasclosetogroundlevelaspossible.Makesurethevent
area is not blocked by interior supports of the structure.
• Werecommendventswithscreens.
• Accessdoorstothestructurearenotconsideredvents.
• Cleantheventsperiodically.
bUILT-IN TANK eNcLoSURe ASSembLY VeNTILATIoN
m




◆
m 

These parts may be gas carrying or gas burning components. Please contact Weber-Stephen Products LLC Customer Service
Department for genuine Weber-Stephen Products LLC replacement part(s) information.
m 



WEBER-STEPHEN PRODUCTS LLC
www.weber.com®
© 2011 Designed and engineered by Weber-Stephen Products LLC
a Delaware limited liability company, located at 200 East Daniels Road, Palatine, Illinois 60067 U.S.A.
Printed in U.S.A.