Weber CF 3-II Hd Operating instructions

CF 3-II Hd 1
CF 3-II Hd
Honda GX 160
0100320-00
0819/englisch/Übersetzung der Original-Betriebsanleitung
Operating and
Maintenance Manual
Weber Maschinentechnik GmbH
Im Boden 5– 8, 10
D-57334 Bad Laasphe-Rückershausen/Germany
Tel.: [phone] / 398 0
Fax: [phone] / 398 101
E-mail: [email protected]
Web: www.webermt.de

2 CF 3-II Hd

CF 3-II Hd 3
Table of contents
Introduction 4
Safety guidelines 5
Graphic presentation 8
Device description 9
Technical data 10
Activities prior to starting work 12
Starting 14
Compacting 15
Shutting down 15
Maintenance overview 16
Maintenance work 17
Operating uids and ll levels 19
Troubleshooting 19
Storage 20
Contact addresses 23

4 CF 3-II Hd
Introduction
This operating and maintenance manual is designed to facilitate familiarization with your soil
compactor, and to enable you to maintain the compactor and use it for its intended purpose.
When complying with the instructions in the operating and maintenance manual you help avoid
hazards, reduce repair and downtime costs, and increase the reliability and service life of your soil
compactor.
This operating and maintenance manual must always be available at the implementation site of
the soil compactor.
If necessary, you can obtain additional information from your authorized WEBER MT dealer,
or you can obtain information from one of the contact addresses on the last page.
You can obtain information on the assembled Honda gasoline engine and nd a spare-part list for
it at www.honda-engines-eu.com
The valid conformity declaration is enclosed with every machine delivery.

CF 3-II Hd 5
Safety guidelines
General
All safety instructions must be read and complied with, as non-compliance will result in
– danger to life and limb of the user,
– impairments to the machine or other property.
In addition to the operating manual, the accident-prevention regulations in the country where
the appliance is used must be complied with.
Intended use
The soil compactor should only be used if it is in a technically faultless condition, as intended,
in a safety-conscious and hazard-conscious manner, in compliance with the instructions in
the operating manual. Malfunctions that impair safety must be eliminated without delay.
The CF 3-II Hd soil compactor is designed exclusively for compacting
– sand,
– gravel,
– asphalt, crushed rock,
– low-cohesive mixed material,
– concrete paving stone.
Any other use of the soil compactor is considered to be improper use for which the owner
shall be exclusively responsible. All liability is rejected if damage occurs due to non-compliance
with this provision. This risk is borne solely by the user.
Easily foreseeable misuse
Any use for which the machine is not intended.
Operation
Soil compactors are only permitted to be operated by suitable persons of or above the age of 18.
Personnel must be instructed in how to guide the compactor by the owner or by the owner’s
assigned personnel.
The machine operator must comply with trafc regulations. If instructions that affect safety are given
by third parties, then the operator must be authorized to reject these instructions.
Unauthorized persons are forbidden from being in the area of the soil compactor during
the compacting process.
Protective equipment
This machine is capable of exceeding the permissible sound level of 80 dB(A). The owner might also
face additional dangers when using the machine. Precautionary action must, therefore, be taken.
Protective equipment includes:
Hearing protection
Hard hat
Safety shoes
Protective gloves

6 CF 3-II Hd
Operation
Prior to starting work the owner of the compactor must be familiar with the work environment.
The work environment includes obstacles in the work and trafc area, the bearing capacity of
the ground, as well as the necessary safeguarding of the construction site in the area adjacent to
public trafc; and it includes compliance with trafc regulations.
The soil compactor should only be operated when the protective xtures are mounted. The protective
xtures must all be in functional condition.
At least once per shift the compactor must be checked for apparent defects. If there are apparent
defects then operation of the compactor must be stopped immediately, and the responsible person
must be informed. Prior to restarting, compactor malfunctions that have occurred must be corrected.
Always maintain adequate clearance to the edges of pits and embankments.
Do not drive at ninety degrees to slopes to prevent the compactor from tipping over.
After work has been concluded secure the compactor in accordance with statutory regulations,
particularly in the area of public trafc surfaces.
Operation under difcult conditions
Never inhale the exhaust gas. It contains carbon monoxide, a colorless and odorless gas that
is extremely hazardous, which, if inhaled even briey, can cause unconsciousness and death.
Therefore, never operate the engines in enclosed areas or in areas that are poorly ventilated
(tunnels, caves, covered pits, etc.).
Exercise particular caution when operating the engine in the vicinity of people and livestock.
Maintenance and repair work
Only use original Weber MT spare parts to ensure reliable and safe operation for maintenance
or repair work.
Hydraulic hose lines must be checked at regular intervals in accordance with standard engineering
practice, or they must be replaced at appropriate intervals, even if no signs of safety-relevant defects
are present.
Adjusting tasks, maintenance tasks, and inspection tasks must be carried out on schedule as
specied in this operating and maintenance manual. These activities should only be executed
by instructed personnel.
For repair, service, or inspection work the engine of the compactor must be safeguarded against
unintentional starting.
All pressurized lines, particularly hydraulic lines and lines of the injection system of the drive motor
must be depressurized before performing maintenance or repair tasks.
For maintenance and repair tasks the compactor must be parked on a level and stable substrate
and must be secured from rolling off or tipping over.
Heavy components and assemblies must be secured to and lifted by hoisting machines that can
bear their weight when they are replaced. Ensure that no hazard is caused by raising components
or assemblies.
Do not position yourself or work under suspended loads.
If lubricating oils and fuel come into contact with skin, they can cause skin cancer. Upon contact
with the skin, clean affected skin with suitable cleaning agent without delay.

CF 3-II Hd 7
Inspection
Compactors must be inspected in accordance with the corresponding implementation conditions and
operating conditions, as needed; however, an inspection to ensure operationally safe status must be
performed by an expert at least once a year. The results of the inspection must be recorded in writing
and must be stored at least until the next inspection.
Cleaning work
Prior to cleaning the compactor with a high-pressure cleaner, protect all accessible energized
switches, cable connections, etc. against water penetration by masking them off.
Cleaning tasks should only be executed in areas that are suitable and have been approved for
this purpose (oil separator amongst others).
Disposal
All operating uids and auxiliary materials must be disposed of in an environmentally-compatible
manner in accordance with country-specic regulations.
Warning against irritants or materials hazardous to health
Warning against a hazardous place
Warning against a suspended load
Wear ear protection
General regulation
Environmental protection
Important information for operating and maintenance personnel is marked by pictograms.
Hard hat
Safety shoes
Protective gloves

8 CF 3-II Hd
3
8
4
5
2
7
6
9
1
Overall view – CF 3-II Hd
1 Water tank (no image/accessory)
2 Engine
3 Manual guidance rod
4 Undercarriage (no image/accessory)
5 Engine bracket
6 Base plate
7 Hearing protection (sticker)
8 Gas lever
9 Exciter
Graphic presentation

CF 3-II Hd 9
Device description
The CF 3-II Hd soil compactor is used for road-building and landscaping compaction tasks.
Drive
The unit is powered by an air-cooled Honda gasoline engine.
Force is transferred to the exciter mechanically via a V-belt.
Operation
Start the Honda gasoline engine with the attached reversing starter. After starting,
vibration is switched on via the centrifugal clutch attached to the engine.
The manual guidance rod is used to steer the soil compactor.

10 CF 3-II Hd
CF 3-II Hd
Weight
Operating weight CECE in kg 94
Dimensions
Overall length (in mm) 1100
Overall width (in mm) 500
Height with folded guide bar (in mm) 550
Base plate length (in mm) 400
Pressure surface (in mm) 400x500
Drive
Engine manufacturer Honda
Type GX 160
Performance at operating speed in accordance
with ISO 3046-1 (kW) 2.7
Combustion process 4-stroke gasoline
Operating speed (1/min) 3000
Drive speed forward (ground-dependent in m/min) 24
Incline capacity (ground-dependent in %) 35
Area capacity (in m²/h) 720
Vibration
System Single shaft vibrator
Drive concept Mechanical
Frequency (in Hz) 95
Centrifugal force (in kN) 20
CF 3-II Hd
Noise emissions in accordance with 2000/14/EC
Sound pressure level LPA
ascertained in accordance with EN 500, in dB (A) 91
Sound power level LWA
ascertained in accordance with EN ISO 3744
and EN 500, in dB (A) 105
Vibration values
Root-mean-square acceleration value
for hand-arm vibration ascertained
in accordance with EN 500 in m/s² 3.1
In accordance with directive 2006/42/EC,
complying with the vibration values is the
owner’s responsibility.
Technical data

CF 3-II Hd 11
2
1
3 4
56
1 Description 2 TYPE
.................................................... ...................................................
3 Serial number 4 Year of construction
.................................................... ...................................................
5 Mass 6 Rated power kW
.................................................... ...................................................

12 CF 3-II Hd
1
1
1
2
2
Mounting the undercarriage
Use the screws (2) to fasten the undercarriage (1) to
the engine bracket.
Pivot the hand truck under the base plate.
The manual guidance rod must be locked during
transport.
Arrest the guide bar (1) with the spring bolt (2).
Fit the crane hook into the lifting ring (1) and lift the machine
onto the desired means of transport.
Activities prior to starting work
When transporting the soil compactor on a vehicle,
secure it with suitable restraints.
Only use lifting machines with a minimum bearing
capacity of 150 kg.
Do not step under suspended loads.
Transport

CF 3-II Hd 13
1
1
1
Installing the protective mat
Hook in the protective mat at the rear.
Ensure that the protective mat rests under the base plate.
Open and remove the gas cap (1), check the level,
if necessary top off to the lower edge of the ller neck
with clean fuel in accordance with the specication.
The correct oil level is between the min. and max. marks.
Check the engine oil level
Pull the oil dipstick (1) out of the crankcase.
Check the fuel level
Insert the oil dip stick in the oil ller neck, but do not
screw it in.
Fasten with holder, screws, spring-lock washers and nuts on
the base plate (1) at the front.
For work at the fuel system, have a suitable re-
extinguishing agent at the ready.
Fire, naked light, and smoking is forbidden!
Max.
Min.
UPPER LEVEL
LOWER LEVEL

14 CF 3-II Hd
1
2
3
12
1
2
3
1
Starting
After the engine has warmed up, slide the choke lever to
the right (open).
Mounting the water sprinkling system
Open the fuel cock (3).
Slowly tighten the handle (1) of the reversing starter (2) until
resistance is noticeable.
Allow the handle (1) to glide back into the initial position, and
then forcefully and completely pull it through with both hands.
Completely empty the water tank if there might be a frost.
Slide the choke lever (2) to the left (close).
Bring the gas lever (1) into full-throttle position.
Turn the short-circuit button (1) to the “ON” position.
Lift the water tank (1) into the frame (2).
Attach the water spray pipe (3) to the base plate.

CF 3-II Hd 15
1
1
2
1
1
Shutting down
Bring the gas lever (1) into idle position.
Compacting
Control drive speed and direction of travel with
the handle (1).
Bring the gas lever (1) into full-throttle position.
Close the fuel cock (2).
Turn the short-circuit button (1) to the “0” – OFF position.
Only run machine within reach of the guide bar.
During breaks – even if they are short – the machine
must be shut down.
Parked devices that represent an obstacle must be
safeguarded against through conspicuous measures.

16 CF 3-II Hd
Maintenance overview
Maintenance interval Maintenance point Maintenance activity
After the rst
25 operating hours
Engine – Change the engine oil
–Check valve play;
adjust if necessary
– Re-tighten all accessible
threaded connections
Every 8 operating
hours / daily
Air lter –Clean air lter insert,
check for damage,
replace if necessary
Every 150 operating
hours / every six months
Engine – Change the engine oil
Every 150 operating
hours / every year
Vibrator – Change oil
Engine – Adjust valve play
–Clean spark plug/adjust
electrode gap
The regulations of the engine manufacturer must be complied with in addition to the
above maintenance overview!
Work must be carried out using regulation tools, and the operating and maintenance
manual must be complied with for all work.
All maintenance work: Select collection vessels large enough to prevent oil from spilling
onto the ground. Dispose of waste oil in an environmentally friendly manner (regulation
on waste oils).
Dispose of oils, greases, cloths soaked in oil, and replaced parts with oil on them in an
environmentally friendly manner.
If lubricating oils and fuel come into contact with skin, they can cause skin cancer.
Upon contact with the skin, clean affected skin with suitable cleaning agent without delay.
If accessible during maintenance, check the condition and stability of all screws.

CF 3-II Hd 17
1
1
2
1
Change the engine oil
Remove the oil dip stick (1).
When working in the area of the engine compartment
there is a danger of being burnt!
Remove the oil drain screw (2) and drain oil.
After emptying completely, put in the oil drain plug /locking
screw (2). Top up oil as specied.
Clean / change air lter cartridge
Unscrew the air lter cover (1).
Remove the air lter insert (1) from the air lter enclosure.
Clean air lter insert as specied by the engine manufacturer
if there is damage or if it is extremely dirty.
Maintenance work
Only drain engine oil when at operating temperature.
Risk of scalding due to hot oil.
If lubricating oils and fuel come into contact with skin, they
can cause skin cancer. Upon contact with the skin, clean
affected skin with suitable cleaning agent without delay.
Dispose of oils, greases, cloths soaked in oil, and
replaced parts with oil on them in an environmentally
friendly manner.

18 CF 3-II Hd
1
1
1
Remove the oil drain plug / ller plug (1) and drain oil.
Fill with oil as specied in the ll quantity table.
Screw in oil drain plug or ller plug.
Checking the V-belt
Remove the V-belt guard (2).
Check the V-belt (4) for cracks, damaged anks, and wear.
If there is excessive wear, replace the V-belt.
Select collection vessels large enough to prevent oil from
spilling onto the ground. Dispose of waste oil in an envi-
ronmentally friendly manner (regulation on waste oils).
Wipe up/off oil slick and oil residue and dispose of fuel-
soaked cleaning cloths in an environmentally responsible
manner.
Ensure that the contact surfaces on the oil drain plug / ller
plug and vibrator housing are clean.
Changing the oil in the exciter

CF 3-II Hd 19
Assembly Operating material Quantity
Summer Winter CF 3-II Hd
Quality
Engine
Engine oil SAE 10 W 40 0.6 l
(–10 ~ +50 °C)
API – CD CE
of SHPD
or CCMC – D2 – D3 – PD1
Fuel tank
Gasoline Unleaded gasoline 3.1 l
Vibrator Engine oil 10 W 40/15 W 40 0.2 l
Fault Possible cause Remedy
Soil compactor
does not start
Operating error Execute the start
process as prescribed
Lack of fuel Check the fuel level
Fuel lter fouled Change the fuel lter
Air lter fouled Clean / change air lter
cartridge
No vibration / no
forward motion
or insufcient
forward motion
Vibrator V-belt defective Change vibrator V-belt
Operating uids and ll levels
Troubleshooting

20 CF 3-II Hd
If the machine is to be stored for longer than six months, then contact the Weber service
organization to discuss additional measures.
Actions to be taken before long-term storage (longer than 1 month)
Entire soil compactor – Clean thoroughly
– Check for leaks
– If there are leaks –
correct defects
Fuel tank –Empty fuel and ll with clean fuel
up to the lower edge of ller neck
Engine – Check oil level, if necessary
ll to upper oil-level mark
–Check air lter, clean,
replace if necessary
–Check fuel lter, change
if necessary
All bare parts / gas lever / accelerator
control cables / fastening bolts
–Oil/grease