Weidmuller Power Monitor 51A User manual

Power Monitor / Power Monitor 51A
Quick guide to set up a connection with the Power Monitor devices through the Weidmüller
Serial/Ethernet Converter

1502950000/01/03.15 3
1.1 Revision history
Version Date Change
0.0 11/2013 First edition
1.0 03/2015 Page 5, software Power
Monitor Manager updated
from version 1.10 to
version 1.20
1.2 Contact address
Weidmüller Interface GmbH & Co. KG
PO Box 3030
32720 Detmold
Klingenbergstraße 16
32758 Detmold
Germany
Phone [phone]
Fax [phone]
E-mail [e-mail]
Internet www.weidmueller.com

Table of contents
4 1502950000/01/03.15
Table of contents
1.1 Revision history ................................................................................................................................3
1.2 Contact address................................................................................................................................3
Table of contents...............................................................................................................4
2. Introduction...........................................................................................................5
2.1 Copyright and trademark .................................................................................................................5
2.2 Types / article numbers....................................................................................................................5
2.3 Requirements ....................................................................................................................................5
3. Configuring Serial/Ethernet Converter................................................................6
4. Configuring Power Monitor................................................................................15

Introduction
1502950000/01/03.15 5
2. Introduction
This is a quick guide to set up a connection with the
Power Monitor devices through the Weidmüller
Serial/Ethernet Converter.
2.1 Copyright and trademark
•Weidmüller owns the copyright of this quick guide.
•No part of this quick guide may be reproduced in
any form or by any means without prior permis-
sion.
•Modbus Protocol is a communication protocol that
developed by Modicon Inc. for PLC. Modbus is the
registered trademark of Schneider Electric.
•All other company names or product names that
may be mentioned in this publication are trade-
marks or registered trademarks of their respective
owners.
2.2 Types / article numbers
This quick guide covers the following product types /
article numbers
Power Monitor 1423550000
Power Monitor 51A 1470260000
2.3 Requirements
Please set up the Serial/Ethernet Converter as
described in the related installation guide.
Software
•Install the enclosed software Power Monitor
Manager, version 1.20 and S/E-Converter
Administrator.
•Power Monitor software needs the Microsoft .NET
Framework 4.0 to run.
Wiring
Connect the Power Monitor and the Serial/Ethernet
Converter via the Modbus RTU interface. Use the
connection table below.
Power Monitor Serial/Ethernet Converter
Pin 8 Pin 5
Pin 9 Pin 3
Pin 10 Pin 4
Terminal block Serial/Ethernet Converter
Terminal block Power Monitor
Terminal
number 1 2 3 4 5 6 7 8 9 10
Function
L+ N- V1 V2 V3 Vn NC GND
D+ D-
AUX
(Power
supply)
Measured voltage
input – RS485
Ethernet connection
•Connect the Serial/Ethernet Converter to your
local ethernet or directly to your computing device
via an RJ45 cable.
•Make sure you are in the same IP range as the
Serial/Ethernet Converter.
•The default IP of the Serial/Ethernet Converter is
192.168.1.110.
Others
•Make sure you have administrator rights on the
computer.
•Make sure computer and Serial/Ethernet
Converter are in the same network sector.

Configuring Serial/Ethernet Converter
6 1502950000/01/03.15
3. Configuring Serial/Ethernet Converter
Start S/E-Converter Administrator.
Click on [Search]. If you have connected the Serial/Ethernet Converter properly to your
network the software will find the device.
Mark the device in the table.
Click on [Configure].
STEP 4
STEP 3
STEP 2
STEP 1

Configuring Serial/Ethernet Converter
1502950000/01/03.15 7
Click on [Network) to see the network configuration. Click the [Modify] check box to modify
the configuration if needed.
STEP 5

Configuring Serial/Ethernet Converter
8 1502950000/01/03.15
Click on the [Serial] tab.
Click the [Modify] check box.
Mark the device in the table.
Click on the [Settings] button.
STEP 9
STEP 8
STEP 7
STEP 6

Configuring Serial/Ethernet Converter
1502950000/01/03.15 9
Set the parameters as follows:
•Baud Rate: 19200
•Parity: Odd
•Data Bits: 8
•Stop Bits: 1
•Flow Control: None
•FIFO: Enable
•Interface: RS-485, 2 wire
NOTICE
All values must be equal to the values in the Power Monitor.
Confirm by clicking on [OK].
STEP 11
STEP 10

Configuring Serial/Ethernet Converter
10 1502950000/01/03.15
Click the [Operating Mode] tab.
Click the [Modify] check box.
Mark the first row in the table.
Click on [Settings] and set [Operating Mode] to “Real COM Mode”.
Confirm by clicking on [OK].
STEP 16
STEP 15
STEP 14
STEP 13
STEP 12

Configuring Serial/Ethernet Converter
1502950000/01/03.15 11
Click on [COM Mapping].
Click on [Add], check the box and confirm by clicking on [OK].
STEP 18
STEP 17

Configuring Serial/Ethernet Converter
12 1502950000/01/03.15

Configuring Serial/Ethernet Converter
1502950000/01/03.15 13
Click on the upper row in the main window.
Click on [Configure].
Select a COM Port.
STEP 21
STEP 20
STEP 19

Configuring Serial/Ethernet Converter
14 1502950000/01/03.15
Click on the [Serial Parameters] tab.
Set the parameters to the same values as in step 10 and on the Power Monitor, i.e.
•Baud Rate: 19200
•Parity: Odd
•Data Bits: 8
•Stop Bits: 1
•Flow Control: None
NOTICE
All values must be equal to the values in the Power Monitor.
Confirm by clicking on [OK].
Click on [Apply] in the main window.
STEP 25
STEP 24
STEP 23
STEP 22

Configuring Power Monitor
1502950000/01/03.15 15
4. Configuring Power Monitor
Firstly, please change the protocol from MEWTOCOL to MODBUS in the Power Monitor and set communica-
tion parameters as follows:
•Baud Rate: 19200
•Parity: Odd
•Data Bits: 8
•Stop Bits: 1
Start the Weidmüller Power Monitor Manager.
Under [Settings] select [Communication setup].
STEP 27
STEP 26

Configuring Power Monitor
16 1502950000/01/03.15
Set [Network] to “RS232C“.
Set [Communication port] to the same port as described in step 22.
Set the other parameters to the same values as in step 10 and on the Power Monitor:
•Baud Rate: 19200
•Parity: Odd
•Data Bits: 8
•Stop Bits: 1
STEP 30
STEP 29
STEP 28

Configuring Power Monitor
1502950000/01/03.15 17
NOTICE
All values must be equal to the values in the Power Monitor.
Confirm by clicking on [OK].
STEP 31

Configuring Power Monitor
18 1502950000/01/03.15
Click on [Display].
Now there must be a connection between the Power Monitor and the computer (see status on the bottom left
“Communication success”).
STEP 32

Weidmüller Interface GmbH & Co. KG
PO Box 3030
32720 Detmold
Klingenbergstraße 16
32758 Detmold
Germany
Phone [phone]
Fax [phone]
E-mail [e-mail]
Internet www.weidmueller.com Order number: 1502950000/01/03.15