Wellav Technologies UMH 160 User manual


Wellav Technologies Ltd. 1
UMH 160 Quick Installation Guide V1.1-W
UMH160 Integrated Digital Receiver
Quick Installation Guide


Wellav Technologies Ltd. 2
UMH 160 Quick Installation Guide V1.1-W
Preface
About This Document
This document provides introductions and guidelines to users about how to install and
operate this equipment quickly.
Disclaimer
Wellav Technologies Ltd. assumes no responsibility for errors or omissions that may appear
in this publication. It reserves the right to change this publication at any time without notice.
This document is not to be construed as conferring by implication, estoppel, or otherwise
any license or right under any copyright or patent, whether or not the use of any information
in this document employs an invention claimed in any existing or later issued patent.
Intended Readers
zTechnical Service Engineer
zMaintenance Engineer
zTest Engineer
zSales Engineer
Symbols Definition
For the symbols that might appear in this document, the meanings they represent are as the
following:
Symbol Meaning
There is potential danger. If it cannot be avoided, it will lead to the deaths or
serious injury.
There is medium or low potential danger. If it cannot be avoided, it will lead to
medium or mild injury.


Wellav Technologies Ltd. 3
UMH 160 Quick Installation Guide V1.1-W
There are potential risks. If ignore these texts, it may cause damage to the
device, data loss, equipment performance reduce or unpredictable results.
Tips that help you to solve problems or save your time.
Remarks. Additional information to the text, in order to emphasize something.
Revision History
The revision history lists the modification history. The newest one contains all the
modifications of the past revision.
V1.00: First revision. (Date: March 5th, 2012)


Wellav Technologies Ltd. 4
UMH 160 Quick Installation Guide V1.1-W
Content
1. Safety ............................................................................................................................5
2. Check Package and Accessories ..................................................................................6
3. Physical specifications...................................................................................................7
3.1 Physical Specifications ..........................................................................................7
3.2 Interfaces and data IN/OUT capabilities ................................................................7
4. Front Panel and Rear Panel .......................................................................................... 9
4.1 Front Panel ............................................................................................................9
4.2 Rear Panel............................................................................................................. 9
5. Installation Instruction .................................................................................................. 10
5.1 Mounting unit to a 19” rack ..................................................................................10
5.2 Wiring Connection ...............................................................................................12
5.3 Power Connection ............................................................................................... 13
6. Operation Instructions .................................................................................................14
6.1 Powering Up & Initializations ...............................................................................14
6.2 Network Connection Setup .................................................................................. 14
6.2.1 Navigation Keys Operation Instruction............................................................. 14
6.2.2 Check Out and Change the Default IP Address ...............................................15
6.2.3 Configuration through WEB Management........................................................16
6.3 Quick Configuration on Key Parameters.............................................................. 18
6.3.1 Check “Status” tab............................................................................................18
6.3.2 Configure parameters of signal input modules.................................................18
6.3.3 Configure parameters of signal output modules............................................... 23
6.3.4 Change the password ......................................................................................28
6.3.5 Check “Status” again........................................................................................29


Wellav Technologies Ltd. 5
UMH 160 Quick Installation Guide V1.1-W
1.Safety
zTo avoid electric shock hazards, do not open the receiver; refer service to qualified
personnel only.
zDo not expose the device in the sunlight, and keep it away from the heat source.
zDo not block ventilation holes of the device so that air can circulate freely.
zSwitch the device off whenever it remains out of service for an extended period.
zBe sure to turn the device off and disconnect the AC power cord before cleaning the
receiver surface.
zThe device shall be connected the mains socket outlet with a protective grounded
connection
zThe appliance coupler used as the disconnect device shall remain readily architecture


Wellav Technologies Ltd. 6
UMH 160 Quick Installation Guide V1.1-W
2. Check Package and Accessories
The Receiver package includes the following accessories:
zUMH160 Base Unit x1
zPower cord x1
zEarth cord x1
zBNC cord x1
zBNC-RCA cord x2
zUser manual Disc x1
Please contact the supplier if it is inconsistent with the actual package.


Wellav Technologies Ltd. 7
UMH 160 Quick Installation Guide V1.1-W
3.Physicalspecifications
3.1 Physical Specifications
Items Index
Power AC 90V-260VAC, 50/60Hz
Power Consumption Approx 125W
Size 1RU
Dimension 482mm(L) x44mm(W) x 393mm(H)
Net Weight Approx 3.8Kg
Gross Weight Approx 5Kg
3.2 Interfaces and data IN/OUT capabilities
Physical Connector Interfaces
Inputs ● DVB-S/S2 Input
Constellation: QPSK, 8PSK
Symbol Rate: 1~45 Mbps
FEC: All rations compliant with standard
Signal Level: -65 ~ -25 dBm
● DVB-T Input(optional)
Contellation: COFDM, 2K & 8K FTT
Symbol Rate: 0.45~7 Mbps (QPSK)
Frequency: 174 ~ 230 MHz, 474 ~ 858 MHz
Signal level: -80 ~ -20 dBm
● DVB-C Input(optional)
Constellation: QAM ( 16 / 32 / 64 / 128 / 256 )
Symbol Rate: 3 ~ 6.9 Mbps
Frequency: 48 ~ 862 MHz
Signal level: 32 ~ 100 dBuV
● ISDB-T Input (optional)
Constellation: OFDM (64QAM / 16 QAM / QPSK / DQPSK), 2K, 4K,
& 8K FTT
Frequency: 470 ~ 806 MHz
Bandwidth: 6 MHz
Input impedance: 75 Ω
Input level: -90 ~ -5dBm


Wellav Technologies Ltd. 8
UMH 160 Quick Installation Guide V1.1-W
● DVB-ASI Input
Connector: BNC, 75 Ω
Packet Length: 188 & 204 byte packets
TS Max Bit Rate: 72 Mbps
● TS/IP Inputs (optional)
Connector: 100/1000Base-T, RJ-45
FEC: Pro-MPEG
Encapsulation Protocol: UDP & RTP
Broadcasting type: Unicast and Multicast
Outputs ● Video/Audio Outputs
2xCVBS outputs (1 BNC, 1 RCA)
1xComponent output (YPbPr)
1xHDMI output (with HDCP, 720p & 1080i)
1xAES/EBU digital audio output
2xHD/SD-SDI outputs (with embedded digital audio)
● DVB-ASI Outputs
Connector: BNC, 75 Ω
Packet Length: 188 & 204 byte packets
TS Max Bit Rate: 72 Mbps
● TS/IP Outputs (optional)
Connector: 100/1000Base-T, RJ-45
FEC: Pro-MPEG
Up to 8 streams Multicast or Unicast
Broadcasting type: Unicast and Multicast
Supporting Protocol: DHCP, TCP/IP, ARP, IGMP (V2/V3)
Analog
Unbalanced
Audio
● L-AUDIO-R
Output Interface: RCA*2, 1 groups of Left/Right Channel audio
Max Output Level: 7 dBu
Output Impedance: 600 ohm
● AES/EBU
Output Interface: XLR*1
Max Output Level: 2~5V peak to peak
Output Impedance: 110 ohm
Management
zManagement Port
Interface: 100BaseTX,RJ45
Web-based Management


Wellav Technologies Ltd. 9
UMH 160 Quick Installation Guide V1.1-W
4.FrontPanelandRearPanel
4.1 Front Panel
1 2 3 4 5 6 7 8
PIC-4.1-1
Item No. Functionality
1 Power status indicator
2 (Signal) Lock status indicator
3 Alarm status indicator
4 LED displaying screen
5 CI SLOTS
6 KEY PADS, including Up/Down/Left/Right arrow keys
7 Menu. To enter the menu and the quit function of the sub menus.
8 ESC. The quit function of the menu.
4.2 Rear Panel


Wellav Technologies Ltd. 10
UMH 160 Quick Installation Guide V1.1-W
5 6 8 9
PIC-4.2-1
Item No. Functionality
1 TS/IP: TS stream input and output as IP format
2 AES/EBU: Professional digital Audio output with XLR connector.
3 HDMI: Output high quality picture and sound with one cable.
4 Cr/Cb/Y: Component output.
5 VIDEO /AUDIO: Video signal output jack and Left/right audio output jack.
6 ASI IN: BNC connector for TS input.
7 CVBS OUT: Output video with BNC interface.
8 SDI OUT: Output the SDI Video stream.
9 ASI OUT: Output MPEG-2 or Mpeg-4 TS.
10 ETHERNET: The port is used in network remote control.
11 TUNER OUT (LOOP OUT): Use it when connecting to another IRD.
12 TUNER IN: Connect to a RF or IF signal.
13 POWER SUPPLY and POWER SWITCH: 90~250V AC, 50Hz.
Inrush Current at initial switch on: 1.55A. Inrush Current after power supply
interruption: 2.3A.
5.InstallationInstruction
5.1 Mounting unit to a 19” rack
When selecting the installation site, try to comply with the following:
12347 12910 11813


Wellav Technologies Ltd. 11
UMH 160 Quick Installation Guide V1.1-W
zProtective Ground - The protective ground lead of the building's electrical
installation should comply with national and local requirements.
zEnvironmental Condition - The installation site should be dry, clean, and
ventilated. Do not use this equipment where it could be at risk of contact with water.
To avoid electric shock, make sure the rack has been correctly grounded
before switching device on the.
To mount the receiver unit to a 19”/42U rack, please perform the following steps:
1. Make sure the mounted rack surface is stable and can support the size and weight of this
equipment.
2. For single unit mounting, use an “L” shape slide (not included in the package) to support
holding the unit if necessary, and fastened with appropriate screws to each side of the
chassis’ rails.
L-shape slide
3. For group pile up (no space between each unit), the unit should be placed on a flat
holding bracket. No more than 5 units for each group, and leave at least one unit space
between each group to ensure good air ventilation.
PIC-5.1-1 Grounding Jackscrew ( must be connected to the rack housing)


Wellav Technologies Ltd. 12
UMH 160 Quick Installation Guide V1.1-W
PIC-5.1-2
5.2 Wiring Connection
Before setting up the connection, please turn off the equipment and all other
connected external devices. The equipment and all connected external devices are
required grounded. Turn on the devices only after the wiring connection is completed.
Otherwise, the device may be damaged.
Follow the below connection diagram to set up cable connection:
PIC-5.2-1
zSet up cable connection for input signal: either the RF input or ASI input.
zSet up cable connection for output signal: either through ASI or HDMI/ CVBS/SDI.
zSet up connection for network management control.
In order to ensure a smooth communication between the management PC and
1
2 5
4
3


Wellav Technologies Ltd. 13
UMH 160 Quick Installation Guide V1.1-W
the equipment, please separate the connection of management port and TS/IP output
port to different switch. The switch with management port connected should be
without large data processing.
The TS/IP port can work for input and output simultaneously. User only needs
to connect one RJ45 cable to the TS/IP port of the device.
5.3 Power Connection
Connect this equipment only to the power sources that are identified on the
equipment-rating label normally located close to the power inlet connector(s).
Always pull the plug or the connector to disconnect a cable. Never pull on the cable
itself.
To protect your valuable interests and services, equipping a UPS
(Uninterrupted Power Supply) and an AVR (Automated Voltage Regulator) to the
system is highly recommended.


Wellav Technologies Ltd. 14
UMH 160 Quick Installation Guide V1.1-W
6.OperationInstructions
6.1 Powering Up & Initializations
Before powering-up the device, make sure that all cabling is correctly
connected (refer to chapter PIC-5-2-1). The device is correctly connected to the power
inlet and grounded.
Switch on the equipment through the back power switch, the unit is powered up and start the
initialization.
The LCD screen is lighted up, and display information as following:
PIC-6.1-1
The initialization takes about 30 seconds to complete.
If the unit fails to initialize and hangs at the “booting” stage, swtiching off the
device and then powering up again. If the device still fails to initialize, please contact
your service representative for help.
The input/output indicator LEDs turn red after successful initialization because
of signal unlocking. After configuration on the device, corresponding LEDs shall
show correct statuses.
6.2 Network Connection Setup
6.2.1 Navigation Keys Operation Instruction
Use the 6 navigation keys on front panel: Up / Down / Left / Right / Menu / Ok to
UMH160
SettingSystem


Wellav Technologies Ltd. 15
UMH 160 Quick Installation Guide V1.1-W
enter the configuration menu.
zEnter “Menu”:
Press “MENU” button to enter main menu.
zExit Menu/Back to parent Menu
Upon completion of configuration settings, press “MENU” button until you go back
to the Parent Menu.
You can also go back to Parent Menu directly by pressing “ESC” button once.
zEnter Sub-Menu
Press MENU button to enter main menu.
Select a sub-menu by pressing UP and DOWN button.
Press OK button on the selected sub-menu.
zTo change parameter
Step 1: Enter main menu by pressing MENU button.
Step 2: Scroll sub-menu by pressing UP and DOWN button, and press OK button
to change the selected sub-menu.
Step 3: To change parameter settings, press RIGHT and LEFT button to move the
cursor in which change must be made.
Press UP button and DOWN to input / select an appropriate setting, then press OK
button to save.
6.2.2 Check Out and Change the Default IP Address
zStep 1: check out the IP on the LCD screen.
zStep 2: use the button on the front panel to change the IP, gateway and subnet mask.
The gateway should be the same as the management PC’s. The subnet mask should
be the same as the management PC’s s. The IP and the server’s IP should be in the
same section.
zStep 3: reboot the device to take effect.
zStep 4: ping the new IP on PC to check whether the device can connect to the
management PC.


Wellav Technologies Ltd. 16
UMH 160 Quick Installation Guide V1.1-W
6.2.3 Configuration through WEB Management
Accessing the equipment through web can be very convenient for remote
configuration of the equipment. Relative to the front panel settings, web operation
can provide a more user-friendly man-machine interface, and less limits in space. For
quick installation, web operation is highly recommended. In this installation guide,
operation instruction is based on web style. For front panel operation instruction,
please refer to product user manual.
zPreparation before connection
Open any web browser (e.g. Mozilla, internet explorer, safari etc.), input the equipment’s IP
address in format: http://xxx.xxx.xxx.xxx (xxx.xxx.xxx.xxx refers to IRD’s IP address) and
press ENTER button to confirm. The browser will attempt to connect to the device. If
succeed, a login page will appear (see pic-6-2-1).
zFirst Time Log On
oFor first time log on, User Name and Password are required. Default User Name
and Password are “admin”.
PIC-6.2-1


Wellav Technologies Ltd. 17
UMH 160 Quick Installation Guide V1.1-W
User can change the password after log on the device. Please refer to chapter XXXX
of this document for the details. (Referring chapter 6.3.4)
Possible reasons for unsuccessful log on:
zIP address/ network mask/gateway don’t match with the management PC’s
zUser name/password is wrong.
zThe device is connected to the wrong interface.
zMain Interface Introduction
After logging in successfully, it will search the HD IRD which is connected to the server and
display it on the left side as below automatically.
PIC-6-2-2
The main interface can be divided into two areas according to its functionality.
1.Menu: It share same 6 tabs including “Status”, “Inputs”, “Outputs” and “System”.
2.Parameter setting and configuration area: The parameters of the equipment are shown
and configured here by selecting corresponding tabs. This is the main operation area of the
WEB management.


Wellav Technologies Ltd. 18
UMH 160 Quick Installation Guide V1.1-W
6.3 Quick Configuration on Key Parameters
6.3.1 Check “Status” tab
Click the “status” tab on the left area and then the status information will show on the right
interface as following, where you can check the main information of the device.
PIC-6-3-1
6.3.2 Configure parameters of signal input modules
Firstly, click the receiver menu to obtain the receiver interface, where you can configure the
detailed parameter as follows:


Wellav Technologies Ltd. 19
UMH 160 Quick Installation Guide V1.1-W
PIC-6-3-2
zTuner IN
If you need to receive the signal from satellite via the device, just connect the satellite siganl
to the tuner port and operate as follows:
-Step one:
PIC-6-3-3
Choose the signal as input ,there are three options:ASI, Tuner and IP, here we choose tunel
as siganl source. After confirm the signal source, it is able to go for further configuration.
-Step two:
Configure the dual RF receiver parameters including the Satellite Frequency, Symbol Rate,
LNB Frequency, and LNB Voltage (Polarization) with accurate values to ensure a successful
receiving. You can get the value for the parameter from the satellite operator
Stepone
Steptwo
Stepfour
Stepthree


Wellav Technologies Ltd. 20
UMH 160 Quick Installation Guide V1.1-W
PIC-6-3-4
zSATELLITE FREQUENCY (MHz): this is the satellite down conversion
frequency, every transponder has one frequency, and this parameter can be
obtain from the satellite program provider or at www.lyngsat.com
zSYMBOL RATE (KBaud): every transponder has one symbol rate; this
parameter can be obtain from the satellite program provider or at
www.lyngsat.com
zLNB LO. Frequency: this is the LNB’s local oscillation (LO) frequency,
every LNB have one or two oscillation frequencies that can be obtained from
the LNB provider, or you can check on the LNB label. The value is between
5000 and 6000..
-Step three
By changing the CAM operation, you can determine whether to descramble the program or
not.
oBYPASS:to transmit the program without any disposal.
oCI SLOT 1 / CI SLOT 2:Common Interface slot. If the program is scrambled, you
can appoint the CAM module with CAM Card to scramble it. Under this condition,
the program is transmitted in default.
oDELETE: any program you don’t want to transmit can be forbidden by selecting
this status.