Welton USA anastasia rl100k User manual

NOTE: T-NUT INSERT MUST BE ON TOP OF SLATS.
STEP 1
INSERT SIDE RAILS(A) INTO THE TOP OF THE
STEP 3
SLOTS IN THE HEADBOARD AND PRESS DOWN.
REPEAT WITH THE FOOTBOARD.
STEP 2
B
ATTACH 2 SLAT SUPPORTS(C) TO EACH SLAT(B)
AS SHOWN.
ATTACH 4 SLATS(B) TO SIDE RAILS(A) WITH 8
WOOD SCREWS(D) AS SHOWN.
A
C
REF. DESCRIPTION QTY.
ASIDE RAIL 2
BSLAT 4
CSLAT SUPPORT 8
DWOOD SCREW
92W0831 8
may have come loose inside the carton during shipment. Place all parts on a clean, smooth surface such as a rug
or carpet to avoid scratching the parts. Be sure you have all the parts and hardware before you begin assembly.
400 Dividend Drive Suite 200 Coppell, TX 75019 Phone [phone] Fax [phone] www.WeltonUSA.com
Welton USA 09-07-10
MODEL : RL100K
ASSEMBLY INSTRUCTIONS
PAGE 1 OF 1
Anastasia
Thank you for purchasing this quality product. Be sure to check all packed material carefully for small parts which
NOTE : DURING ASSEMBLY, DO NOT TIGHTEN ANY HARDWARE UNTIL
THE COMPLETE UNIT HAS BEEN ASSEMBLED.

may have come loose inside the carton during shipment. Place all parts on a clean, smooth surface such as a rug
or carpet to avoid scratching the parts. Be sure you have all the parts and hardware before you begin assembly.
400 Dividend Drive Suite 200 Coppell, TX 75019 Phone [phone] Fax [phone] www.WeltonUSA.com
Welton USA 09-07-10
MODEL : HB100KU
ASSEMBLY INSTRUCTIONS
PAGE 1 OF 1
Anastasia
Thank you for purchasing this quality product. Be sure to check all packed material carefully for small parts which
NOTE : DURING ASSEMBLY, DO NOT TIGHTEN ANY SCREWS UNTIL
THE COMPLETE UNIT HAS BEEN ASSEMBLED.
*HARDWARE KIT 92W1284
STEP 1
D
ATTACH EACH LEG(B,C) TO HEADBOARD PANEL(A) WITH 4 FLAT WASHERS(D), 4 LOCK WASHERS(E) AND
4 SCREWS(F) USING HEX KEY(G) AS SHOWN.
C
B
A
F
E
1
1
CRIGHT LEG
HEADBOARD
ITEM DESCRIPTION QTY.
AHEADBOARD
PANEL 1
BHEADBOARD
LEFT LEG
ITEM DESCRIPTION QTY.
D* 1/4"
FLAT WASHER 8
E* 1/4"
LOCK WASHER 8
F* 1/4"-20 X 1 3/4"
SCREW 8
G* HEX KEY 1

may have come loose inside the carton during shipment. Place all parts on a clean, smooth surface such as a rug
or carpet to avoid scratching the parts. Be sure you have all the parts and hardware before you begin assembly.
400 Dividend Drive Suite 200 Coppell, TX 75019 Phone [phone] Fax [phone] www.WeltonUSA.com
Welton USA 09-07-10
MODEL : HB100KU
ASSEMBLY INSTRUCTIONS
PAGE 1 OF 1
Anastasia
Thank you for purchasing this quality product. Be sure to check all packed material carefully for small parts which
NOTE : DURING ASSEMBLY, DO NOT TIGHTEN ANY SCREWS UNTIL
THE COMPLETE UNIT HAS BEEN ASSEMBLED.
*HARDWARE KIT 92W1075
STEP 1
D
ATTACH THE BED FRAME TO THE HEADBOARD
WITH 4 BOLTS(A), 4 LOCK WASHERS(B), 8 FLAT
WASHERS(C) AND 4 NUTS(D) AS SHOWN.
A
BCC
REF. DESCRIPTION QTY.
A* 1/4"-20 X 2 3/8"
SCREW 4
B* 1/4"
LOCK WASHER 4
C* 1/4"
FLAT WASHER 8
D* 1/4"-20
NUT 4

ATTACH 1 SLAT SUPPORT(C) TO EACH SLAT(B) AS
B
STEP 3
STEP 1
SHOWN.
INSERT SIDE RAILS(A) INTO THE TOP OF THE
SLOTS IN THE HEADBOARD AND PRESS DOWN.
REPEAT WITH THE FOOTBOARD.
NOTE: T-NUT INSERT MUST BE ON TOP OF SLATS.
STEP 2
ATTACH 4 SLATS(B) TO SIDE RAILS(A) WITH 8
WOOD SCREWS(D) AS SHOWN.
A
C
REF. DESCRIPTION QTY.
ASIDE RAIL 2
BSLAT
92W1285 4
CSLAT SUPPORT
92W1286 4
DWOOD SCREW
92W0831 8
may have come loose inside the carton during shipment. Place all parts on a clean, smooth surface such as a rug
or carpet to avoid scratching the parts. Be sure you have all the parts and hardware before you begin assembly.
400 Dividend Drive Suite 200 Coppell, TX 75019 Phone [phone] Fax [phone] www.WeltonUSA.com
Welton USA 09-07-10
MODEL : RL100Q
ASSEMBLY INSTRUCTIONS
PAGE 1 OF 1
Anastasia
Thank you for purchasing this quality product. Be sure to check all packed material carefully for small parts which
NOTE : DURING ASSEMBLY, DO NOT TIGHTEN ANY HARDWARE UNTIL
THE COMPLETE UNIT HAS BEEN ASSEMBLED.

may have come loose inside the carton during shipment. Place all parts on a clean, smooth surface such as a rug
or carpet to avoid scratching the parts. Be sure you have all the parts and hardware before you begin assembly.
400 Dividend Drive Suite 200 Coppell, TX 75019 Phone [phone] Fax [phone] www.WeltonUSA.com
Welton USA 09-07-10
MODEL : HB100QU
ASSEMBLY INSTRUCTIONS
PAGE 1 OF 1
Anastasia
Thank you for purchasing this quality product. Be sure to check all packed material carefully for small parts which
NOTE : DURING ASSEMBLY, DO NOT TIGHTEN ANY SCREWS UNTIL
THE COMPLETE UNIT HAS BEEN ASSEMBLED.
1*HARDWARE KIT 92W1284
QTY.ITEM DESCRIPTION
ATTACH EACH LEG(B,C) TO HEADBOARD PANEL(A) WITH 4 FLAT WASHERS(D), 4 LOCK WASHERS(E) AND
4 SCREWS(F) USING HEX KEY(G) AS SHOWN.
C
B
A
F
E
D
STEP 1
AHEADBOARD
PANEL 1
BHEADBOARD LEFT LEG
92W1282 1
CHEADBOARD RIGHT LEG
92W1283
ITEM DESCRIPTION QTY.
D* 1/4"
FLAT WASHER 8
E* 1/4"
LOCK WASHER 8
F* 1/4"-20 X 1 3/4"
SCREW 8
G* HEX KEY 1

may have come loose inside the carton during shipment. Place all parts on a clean, smooth surface such as a rug
or carpet to avoid scratching the parts. Be sure you have all the parts and hardware before you begin assembly.
400 Dividend Drive Suite 200 Coppell, TX 75019 Phone [phone] Fax [phone] www.WeltonUSA.com
Welton USA 09-07-10
MODEL : HB100QU
ASSEMBLY INSTRUCTIONS
PAGE 1 OF 1
Anastasia
Thank you for purchasing this quality product. Be sure to check all packed material carefully for small parts which
NOTE : DURING ASSEMBLY, DO NOT TIGHTEN ANY SCREWS UNTIL
THE COMPLETE UNIT HAS BEEN ASSEMBLED.
*HARDWARE KIT 92W1075
STEP 1
D
ATTACH THE BED FRAME TO THE HEADBOARD
WITH 4 BOLTS(A), 4 LOCK WASHERS(B), 8 FLAT
WASHERS(C) AND 4 NUTS(D) AS SHOWN.
A
BCC
REF. DESCRIPTION QTY.
A* 1/4"-20 X 2 3/8"
SCREW 4
B* 1/4"
LOCK WASHER 4
C* 1/4"
FLAT WASHER 8
D* 1/4"-20
NUT 4