Welton USA MCB921 User manual

*HARDWARE KIT 92W1583
MADE IN VIETNAM
(#40-218)
ITEM DESCRIPTION QTY.
A
CAPTAINS BED
LEFT PANEL
1
B
CAPTAINS BED
RIGHT PANEL
1
C
CAPTAINS BED
RAIL
2
D
SLAT
ROLL
2
E
TRUNDLE
FRONT FRAME
1
F
TRUNDLE
BACK FRAME
1
G
TRUNDLE
LEFT FRAME
1
H
TRUNDLE
RIGHT FRAME
1
I
DRAWER
SUPPORT
3
J
CROSS
BAR
1
K
DRAWER FACE
92W1587
3
L
DRAWER BOX
92W1588
3
ITEM DESCRIPTION QTY.
M KNOB 6
N
M4 X 35mm
SCREW
6
O*
M8 X 20mm
WOOD DOWEL
6
P*
M8 X 30mm
WOOD DOWEL
4
Q*
M10 X 40mm
WOOD DOWEL
6
R*
20mm
WOOD SCREW
12
S*
30mm
WOOD SCREW
36
T*
M6
FLAT WASHER
14
U*
M6
LOCK WASHER
14
V*
M6 X 30mm
SCREW
21
W*
M6 X 35mm
SCREW
6
X*
M6 X 60mm
SCREW
3
Y*
M6 X 70mm
SCREW
12
Z*
M6
BARREL NUT
12
AA*
HEX
KEY
1
Welton USA 08-11-11
400 Dividend Drive Suite 200 Coppell, TX 75019 Phone [phone] Fax [phone] www.WeltonUSA.com
MODEL : MCB921
Mathew
ASSEMBLY INSTRUCTIONS
PAGE 1 OF 4
Thank you for purchasing this quality product. Be sure to check all packed material carefully for small parts which
may have come loose inside the carton during shipment. Place all parts on a clean, smooth surface such as a rug
or carpet to avoid scratching the parts. Be sure you have all the parts and hardware before you begin assembly.
NOTE : DURING ASSEMBLY, DO NOT TIGHTEN ANY SCREWS UNTIL
THE COMPLETE UNIT HAS BEEN ASSEMBLED.

STEP 1:
ATTACH 2 RAILS(C) TO LEFT AND RIGHT PANELS(A,B) WITH 4 DOWELS(Q), 8 SCREWS(Y) AND 8 BARREL NUTS(Z) USING
HEX KEY(AA) AS SHOWN.
STEP 2
ATTACH LEFT AND RIGHT FRAMES(G,H) TO CROSS BAR(J) WITH 2 FLAT WASHERS(T), 2 LOCK WASHERS(U) AND
2 SCREWS(V).
ATTACH 3 DRAWER SUPPORTS(I) TO THE ASSEMBLY WITH 3 FLAT WASHERS(T), 3 LOCK WASHERS(U) AND 3 SCREWS(V).
C
Z
C
H
I
V
U
G
J
T
I
I
Q Y
A
B
V
U
T
PAGE 2 OF 4
MODEL : MCB921
Mathew
ASSEMBLY INSTRUCTIONS
Welton USA
400 Dividend Drive Suite 200 Coppell, TX 75019 Phone [phone] Fax [phone] www.WeltonUSA.com

STEP 3
ATTACH LEFT AND RIGHT FRAME(G,H) TO FRONT FRAME(E) WITH 4 DOWELS(P), 6 FLAT WASHERS(T), 6 LOCK WASHERS(U)
AND 6 SCREWS(W).
ATTACH EACH DRAWER SUPPORT(I) TO FRONT FRAME(E) WITH 1 FLAT WASHER(T), 1LOCK WASHER(U) AND 1 SCREW(X).
ATTACH BACK FRAME(F) TO LEFT AND RIGHT FRAME(G,H) WITH 2 DOWELS(Q), 4 SCREWS(Y) AND 4 BARREL NUTS(Z).
STEP 4
ATTACH EACH DRAWER FACE(K) TO A DRAWER BOX(L) WITH 2 WOOD DOWELS(O) AND 4 WOOD SCREWS(R).
ATTACH 1 KNOB(M) TO EACH DRAWER FACE(K) WITH 1 SCREW(N). ATTACH 3 KNOBS(M) TO FRONT FRAME(E) WITH
3 SCREWS(N).
SLIDE EACH DRAWER INTO PLACE AS SHOWN.
H
G
L
E
T
M
F
E
II
I
U
X
T
P
W
U
Q
Y
Z
K
O N R
N
M
PAGE 3 OF 4
MODEL : MCB921
Mathew
ASSEMBLY INSTRUCTIONS
Welton USA
400 Dividend Drive Suite 200 Coppell, TX 75019 Phone [phone] Fax [phone] www.WeltonUSA.com

STEP 5:
ATTACH A SLAT ROLL(D) TO EACH BED WITH 18 WOOD SCREWS(S) AND 8 SCREWS(V) AS SHOWN.
STEP 6
SLIDE THE TRUNDLE BED UNDERNEATH THE CAPTAINS BED AS SHOWN.
S
V
V
V
S
V
S
V
V
V
V S
S
S
PAGE 4 OF 4
MODEL : MCB921
Mathew
ASSEMBLY INSTRUCTIONS
Welton USA
400 Dividend Drive Suite 200 Coppell, TX 75019 Phone [phone] Fax [phone] www.WeltonUSA.com