Welton USA MB917 Stafford User manual

*HARDWARE KIT 92W1229
MADE IN MALAYSIA
(#40-51)
FOR 2 SEPARATE TWIN BEDS, ASSEMBLY
BEGINS ON PAGE 2.
FOR BUNK BED, ASSEMBLY BEGINS ON
PAGE 4.
ITEM DESCRIPTION QTY.
A
UPPER LEFT
END PANEL
1
B
UPPER RIGHT
END PANEL
1
C
LOWER
END PANEL
2
D
FRONT
GUARDRAIL
ASSEMBLY
1
E
REAR
GUARDRAIL
ASSEMBLY
1
F
SIDE
RAIL
2
G
SLAT
ROLL
2
H LADDER 1
ITEM DESCRIPTION QTY.
I
LOCATING PIN
92W1231
4
J*
WOOD
DOWEL
8
K*
M6 X 35mm
SCREW
16
L*
M6 X 70mm
SCREW
22
M*
M6
BARREL NUT
22
N*
M4 X16mm
WOOD SCREW
2
O*
M4 X 25mm
WOOD SCREW
40
P*
14.5mm
WOOD PLUG
22
Q*
15.5mm
WOOD PLUG
4
R*
M4
HEX KEY
1
Welton USA 03-12-10
400 Dividend Drive Suite 200 Coppell, TX 75019 Phone [phone] Fax [phone] www.WeltonUSA.com
MODEL : MB917
Stafford
ASSEMBLY INSTRUCTIONS
PAGE 1 OF 5
Thank you for purchasing this quality product. Be sure to check all packed material carefully for small parts which
may have come loose inside the carton during shipment. Place all parts on a clean, smooth surface such as a rug
or carpet to avoid scratching the parts. Be sure you have all the parts and hardware before you begin assembly.
NOTE : DURING ASSEMBLY, DO NOT TIGHTEN ANY SCREWS UNTIL
THE COMPLETE UNIT HAS BEEN ASSEMBLED.

STEP 1: 2 TWIN BEDS
REMOVE THE TOP SIDE RAILS FROM THE GUARDRAIL ASSEMBLIES(D,E) BY REMOVING 8 SCREWS USING HEX KEY(R).
KEEP SCREWS AND GUARDRAILS FOR FUTURE USE.
STEP 2
ATTACH THE 2 TOP SIDE RAILS TO UPPER END PANELS(A,B) WITH 4 DOWELS(J), 8 BARREL NUTS(M) AND 8 SCREWS(L)
USING HEX KEY(R) AS SHOWN.
REPEAT WITH SIDE RAILS(F) AND LOWER END PANELS(C).
D
E
R
A
C
C
B
L
R
J
M
L
J
M
F
F
PAGE 2 OF 5
MODEL : MB917
Stafford
ASSEMBLY INSTRUCTIONS
Welton USA
400 Dividend Drive Suite 200 Coppell, TX 75019 Phone [phone] Fax [phone] www.WeltonUSA.com

STEP 3
ATTACH A SLAT ROLL(G) TO EACH BED WITH 8 SCREWS(K) AND 10 WOOD SCREWS(O) AS SHOWN.
STEP 4
USE 4 WOOD PLUGS(Q) TO FILL THE HOLES ON THE TOP OF THE LOWER END PANELS(C).
USE 22 WOOD PLUGS(P) TO FILL THE HOLES ON THE SIDES OF THE END PANELS.
O
R
K
C
C
Q
P
P
OO
K
K
G
PAGE 3 OF 5
MODEL : MB917
Stafford
ASSEMBLY INSTRUCTIONS
Welton USA
400 Dividend Drive Suite 200 Coppell, TX 75019 Phone [phone] Fax [phone] www.WeltonUSA.com

STEP 1: BUNK BED
START THE TOP BUNK BY ATTACHING GUARDRAILS ASSEMBLIES(D,E) TO UPPER END PANELS(A,B) WITH 4 DOWELS(J),
14 BARREL NUTS(M) AND 14 SCREWS(L) USING HEX KEY(R) AS SHOWN.
START THE BOTTOM BUNK BY ATTACHING 2 SIDE RAILS(F) TO 2 LOWER END PANELS(C) WITH 4 DOWELS(J), 8 BARREL
NUTS(M) AND 8 SCREWS(L).
STEP 2
ATTACH A SLAT ROLL(G) TO EACH BED WITH 8 SCREWS(K) AND 10 WOOD SCREWS(O) AS SHOWN.
O
K
R
KK
G
OO
L
L
R
A
B
C
C
E
F
F
D
M
J
J
M
PAGE 4 OF 5
MODEL : MB917
Stafford
ASSEMBLY INSTRUCTIONS
Welton USA
400 Dividend Drive Suite 200 Coppell, TX 75019 Phone [phone] Fax [phone] www.WeltonUSA.com

STEP 4
ATTACH LADDER(H) TO THE TOP BUNK WITH 2 WOOD SCREWS(N).
STEP 3
ATTACH THE TOP BUNK TO THE BOTTOM BUNK WITH 4 LOCATING PINS(I) AS SHOWN.
USE 22 WOOD PLUGS(P) TO FILL THE HOLES ON THE SIDES OF THE END PANELS.
N
H
I
P
P
PAGE 5 OF 5
MODEL : MB917
Stafford
ASSEMBLY INSTRUCTIONS
Welton USA
400 Dividend Drive Suite 200 Coppell, TX 75019 Phone [phone] Fax [phone] www.WeltonUSA.com