Wenger Essential Lab User manual

Important User Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
General .........................................2
Manufacturer .....................................2
Intended Use.....................................2
Warranty ........................................2
Required Tools. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Hardware Parts List. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Assembly. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Assembly Instructions
Essential Lab Workstation
©Wenger Corporation 2022 Printed in USA 2022-06 Part #256A113-03
Wenger Corporation, 555 Park Drive, P.O. Box 448, Owatonna, Minnesota 55060-0448
USA: (800) 4WENGER (493-6437) • Worldwide: +1-507-455-4100 • wengercorp.com
Contents
Note: Please read and understand these instructions before starting the assembly.
Note: If you need additional information, contact Wenger Corporation using the information below.
Visit the Essential Lab Workstation web page at wengercorp.com for more information.

2
Important User Information
General
Copyright © 2022 by Wenger Corporation
All rights reserved. No part of the contents of this manual may be reproduced, copied, or transmitted in any form
or by any means including graphic, electronic, or mechanical methods or photocopying, recording, or information
storage and retrieval systems without the written permission of the publisher, unless it is for the purchaser's
personal use.
Printed and bound in the United States of America.
The information in this manual is subject to change without notice and does not represent a commitment on the
part of Wenger Corporation. Wenger Corporation does not assume any responsibility for any errors that may
appear in these instructions.
In no event will Wenger Corporation be liable for technical or editorial omissions made herein, nor for direct,
indirect, special, incidental, or consequential damages resulting from the use or defect of these instructions.
The manufacturer reserves the right to change this product at any time.
The information in this document is not intended to cover all possible conditions and situations that might occur.
The end user must exercise caution and common sense when assembling or installing Wenger Corporation
products. If any questions or problems arise, call the Wenger Corporation at (800) 4WENGER (493-6437)
or +1-507-455-4100 worldwide.
Manufacturer
The Essential Lab Workstation is manufactured by:
Wenger Corporation
555 Park Drive
Owatonna, MN 55060
(800) 4WENGER (493-6437) • +1 (507) 455-4100
wengercorp.com
Intended Use
• This product is intended for indoor use in normal ambient temperature and humidity conditions —
it must not be exposed to prolonged outside weather conditions.
• This product is intended to be assembled and used only as described in these instructions.
Warranty
This product is guaranteed free of defects in materials and workmanship for ten full years from date of shipment.
A full warranty statement is available upon request.
Optional power strips, digital locks and other electronic equipment are covered by the individual manufacturer's
warranty.

3
*Quantities may vary, extras can be discarded.
#10 x 1.75"
Pan Head Screw
1
#10-16 x 3/4"
Pan Head Screw
2
1/4-20 x .590"
Machine Screw
3
1/4-20
Cap Nut
4
1/4-20 x 5/8"
Truss Head Screw
5
1/4-20 x 1/2"
Carriage Bolt
6
1/4-20
Lock Nut
7
#10-32 x 3/8"
Pan Head Screw
8
10-32
Jam Lock Nut
9
2-3/8" Grommet
10
Headphone Mount
11
Wiring Clamp
12
3/16"
Allen Wrench
14
5/32"
Allen Wrench
15
Spacer Tube
(Optional)
13
• Phillips head screwdriver
• 3/8" & 7/16" Open-end wrenches, or sockets
• 3/16" Allen wrench (supplied)
• 5/32" Allen wrench (supplied)
Required Tools
Hardware Parts List
9" x 0.75"
Double-Sided Tape
16

4
Assembly
1. Laythedesktopatonthegroundwiththepilotholesfacingup.
Be careful not to scratch the desktop surface!
2. Attach the legs to the bottom of the desktop in the orientation shown below.
a. If including the optional spacer tubes (#13), attach the legs and spacer tubes to the desktop pilot holes
using six #10-16 x 1.75" pan head screws (#1).
b. If not attaching the optional spacer tubes, attach the legs to the desktop pilot holes using
six #10-16 x 3/4" pan head screws (#2).
The use of spacer tubes must be the same on both legs.
If not using optional
spacer tubes
Back of
leg
If using optional
spacer tubes
Example only. If optional spacer tubes are used, they must be attached to both legs.
Spacer
Tube
(#13)
#10 x 1.75"
Pan Head Screws
(#1)
Back of
Desktop
#10 x 3/4"
Pan Head Screws
(#2)
Back of
leg

5
Assembly (continued)
3. Attach the leg cross member to both legs using two 1/4-20 x .590" machine screws (#3) and
1/4-20 cap nuts (#5).
4. Attachthestienertothereardesktoppilotholesusingeight#10-16x3/4"panheadscrews(#2)
as shown.
Leg Cross
Member
1/4-20 x .590
Machine Screws
(#3)
1/4-20
Cap Nuts
(#4)
Stiener
#10 x 3/4"
Pan Head Screws
(#2)

6
Assembly (continued)
5. With the glides facing the inside, attach both
keyboard brackets to the desktop pilot holes
using six #10-16 x 3/4" pan head screws (#2)
in each as shown.
6. Attach the headphone holder to one of the keyboard brackets.
a. Attach to the desktop pilot holes using
three #10-16 x 3/4" pan head screws (#2).
b. Attach to the keyboard bracket using
one 1/4-20 x 1/2" carriage bolt (#6)
and 1/4-20 lock nut (#7).
The headphone holder is typically attached to the
opposite side as the CPU holder.
Left Hand
Keyboard
Bracket
#10 x 3/4"
Pan Head Screws
(#2)
Right Hand
Keyboard
Bracket
Headphone
Holder
1/4-20 x 1/2"
Carriage Bolt
(#6)
1/4-20
Lock Nut
(#7)
Nut inserts
for attaching
optional
CPU holder
#10 x 3/4"
Pan Head Screws
(#2)

7
Assembly (continued)
7. If attaching the optional power strip:
a. Cleanthesurfacesofthepowerstripandthestiener.
b. Remove the backing from one side of the double-sided tape (16) and apply it to the back side of the
power strip.
Note: Foamtapeisdiculttoremoveonceset.Besureoflocationbeforepressinginplace.
c. Remove the backing from the other side of the double-sided tape and mount the power strip to the
stienerasshown.
If not installing a power strip, skip ahead to the next step.
8. Attachwiringclamps(#12)asneededtothestienerwithone #10-32 x 3/8" pan head screw (#8) and
10-32 jam lock nut (#9) in each.
Wiring
Clamp
#10-32 x 3/8"
Pan Head
Screw
(#8)
10-32
Jam Lock
Nut
(#9)
Optional
Power Strip
9" x 0.75"
Double-Sided Tape
(#16)
Use double-sided
tape (#16) to
mount power strip
to stiener

8
Keyboard
Tray
Optional
CPU
Holder
1/4-20 x 5/8"
Truss Head Screws
(#5)
Nut
Inserts
Grommet
(#12)
Assembly (continued)
9. Turn the assembly over.
If attaching the optional CPU holder:
a. Assemble the CPU holder according to the manufacturer's instructions.
b. Attach the CPU holder to
the nut inserts in the desktop
with four 1/4-20 x 5/8"
truss head screws (#5)
as shown.
If not installing a CPU holder,
skip ahead to the next step.
10. Push the grommet (#12) into the hole in the desktop.
11. Tip the keyboard tray into the keyboard brackets and push it closed.
This manual suits for next models
1
Table of contents
Other Wenger Desktop manuals