Wenger Select Lab Fixed Height Workstation User manual

Assembly Instructions
Select Lab Fixed Height
Workstation
Visit the Music Lab Workstations web page at www.wengercorp.com.
Contents
Important User Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Safety Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Required Tools. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Hardware Parts List. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Workstation Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Assembly. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Optional Rackmount Shelf Assembly . . . . . . . . . . . . . . . . . . . . . . 18
Note: Please read and understand these instructions before starting the assembly.
Note: If you need additional information, contact Wenger Corporation using the information below.
©Wenger Corporation 2018 Printed in USA 2018-07 Part #225D099-02
Wenger Corporation, 555 Park Drive, P.O. Box 448, Owatonna, Minnesota 55060-0448
Questions? Call.....USA: (800) 4WENGER (493-6437) • Worldwide: [phone] • wengercorp.com

2
Important User Information
General
Copyright © 2018 by Wenger Corporation
All rights reserved. No part of the contents of this manual may be reproduced, copied, or transmitted in any form
or by any means including graphic, electronic, or mechanical methods or photocopying, recording, or information
storage and retrieval systems without the written permission of the publisher, unless it is for the purchaser’s
personal use.
Printed and bound in the United States of America.
The information in this manual is subject to change without notice and does not represent a commitment on the
part of Wenger Corporation. Wenger Corporation does not assume any responsibility for any errors that may
appear in these instructions.
In no event will Wenger Corporation be liable for technical or editorial omissions made herein, nor for direct,
indirect, special, incidental, or consequential damages resulting from the use or defect of these instructions.
The manufacturer reserves the right to change this product at any time.
The information in this document is not intended to cover all possible conditions and situations that might occur.
The end user must exercise caution and common sense when assembling or installing Wenger Corporation
products. If any questions or problems arise, call the Wenger Corporation at (800) 4WENGER (493-6437)
or [phone] worldwide.
Manufacturer
The Select Lab Fixed Height Workstation is manufactured by:
Wenger Corporation
555 Park Drive
Owatonna, MN 55060
(800) 4WENGER (493-6437) • [phone]
wengercorp.com
Intended Use
· This product is intended for indoor use in normal ambient temperature and humidity conditions —
it must not be exposed to prolonged outside weather conditions.
· This product is intended to be assembled and used only as described in these instructions.
Warranty
This product is guaranteed free of defects in materials and workmanship for ten full years from date
of shipment. A full warranty statement is available upon request.
Optional power strips, digital locks and other electronic equipment are covered by the
individual manufacturer’s warranty.

3
Required Tools
· Phillips Head Screwdriver
· Rubber or Plastic Mallet
· 3/8” Open-End Wrench or Socket
· Drill
· Side Cutter or Scissors
· 3/16” Allen Wrench (supplied)
· 5/32” Hex Insert Bit (supplied)
· 1-3/4” Caster Wrench (supplied)
Safety Precautions
Make sure anyone
assembling the Select
Lab Workstation has read
and understands these
instructions.
!CAUTION
Failure to comply with
Warnings and Cautions in
this document can result
in damage to property or
serious injury.
Throughoutthismanualyoumayndcautionsandwarningswhicharedenedasfollows:
• WARNING means that failure to follow the instruction may result in serious injury or death.
• CAUTION means that failure to follow the instruction may result in serious injury or damage
to property.
Read all of these safety instructions before assembling the Select Lab Fixed Height Workstation.
!CAUTION
To avoid damage and injury,
more than one person is
needed for assembly.
!CAUTION

4
Hardware Parts List
250A508._
7 x 50mm
Particle Board Screw
(color matched paint)
1
X003583
2-3/8” Grommet
X003706
2” 5-Knuckle
Hinge
X000045
#8 x 5/8”
Pan Head Screw
X002540
8 x 25mm
Wood Dowel
5
2
3
4
100A444
Corner
Bracket
6
X003074
Flush Mount
Handle
X000824
#8-18 x 3/8”
Sheet Metal Screw
X003600
Wiring Clamp
X001503
#10-16 x 3/4”
Sheet Metal Screw
7
8
9
10
X002971
1/4-20 x 1/2”
Carriage Bolt
11
X003110
1/4-20
Wing Nut
X001442
1/4 x 47/64”
Flat Washer
X001484
1-1/2” Plug
100A534
1-3/4” Caster Wrench
12 13
14 15
X000482
#8 x 5/8
Sheet Metal Screw
16
X003730
1/4-20 x 1.97
Machine Screw
225D234
Door Stop
Bracket
X003456
Push-In
Bumper
X003741
1/4-20
Cap Nut
17
18
19 20
X003738
#6 x 3/4”
Flat Head Screw
21
X001948
3/16”
Allen Wrench
X001962
5/32” Hex
Insert Bit
X003751
8-32
Hex Nut
X002998
4” Nylon Tie
22 23
24
25
X003743
1/4-20 x 0.708”
Machine Screw
26
250A508
7 x 50mm
Particle Board Screw
(black paint)
27
*Quantities may vary, extras can be discarded.

5
Workstation Components
Item Description Item Description
28 Shelf Wiring Panel 36 Swivel Caster with Brake
29 Front Wiring Panel 37 Standard Swivel Caster
30 Back Panel 38 Adjustable Keyboard Bracket
31 Left Side Panel 39 Bottom Fixed Shelf
32 Right Side Panel 40 Wiring Access Door
33 Desktop 41 Sti󰀨ener
34 Left Side Fixed Tube 42 Pullout Panel
35 Right Side Fixed Tube 43 Headphone Mount
30
32
34
31
33
35
37
39
36
38
40
42
28 29
41
43

6
Assembly
1. Connect the Shelf Wiring Panel (28) and Front Wiring Panel (29)
together using six Wood Dowels (5) and
veBlack 7 x 50 mm Particle Board Screws (27).
2. Attach the shelf Wiring Panel (30) to the Back Panel using
veWoodDowels(5)andfour7x50mmParticleBoardScrews(1).
Shelf Wiring
Panel
(28)
Back Panel
(30)
Front Wiring
Panel
(29)
Wood Dowel
(5)
Black 7 x 50mm
Particle Board Screw
(27)
Wood Dowel
(5)
7 x 50mm
Particle Board Screw
(1)

7
Assembly (continued)
3. Attach four Wiring Clamps (9) to the Back Panel using four
#10-16 x 3/4” Sheet Metal Screws (10).
4. Attach two sets of 5-Knuckle Hinges (3) to the Back Panel using two #6 x 3/4” Flat Head Screws (21).
Only one set of hinges will be attached if an optional Rackmount Shelf Accessory
will be installed.
Be sure that the screws are seated ush with the hinges.
Wiring Clamp
(9)
#10-16 x 3/4”
Sheet Metal Screw
(10)
This set of hinges will not be attached
if a Rackmount Accessory will be
installed.
5-Knuckle
Hinge
(3)
#6 x 3/4”
Flat Head Screw
(20)

8
Assembly (continued)
5. With the top facing up (the side without dowel holes), attach two sets of
Door Stop Brackets (18) to the back side of the Desktop (33) using
two #8 x 5/8” Sheet Metal Screws (17) in each.
Only one set of brackets will be attached if an optional
Rackmount Shelf Accessory will be installed.
6. Push/pull a Push-In Bumper (19) into each
Door Stop Bracket.
Use two Bumpers where there will be
adjoining Wiring Access Doors
Trimo󰀨theexcesstailsusing
a side cutter or scissors.
7. Attach the Front Wiring Panel and Back Panel Assembly to the Right Side Panel (32)
usingthreeWoodDowels(5)andve7x50mmParticleBoardScrews(1).
Leave the Particle Board Screws loose until after Step #8.
Right Side
Panel
(32)
Wood Dowel
(5)
7 x 50mm
Particle Board Screw
(1)
Door Stop
Bracket
(18)
Push-In Bumper
(19)
#8 x 5/8”
Sheet Metal
Screw
(17)
Desktop
(33)
This set of brackets will not be
attached if a Rackmount Accessory will
be installed.
Dowel holes face down.
These two screws may need to
be removed to complete Step #8.

9
Assembly (continued)
8. Use more than one person to attach the Desktop to the Front Wiring Panel and
Right Side Panel using seven Wood Dowels (5) and
three 7 x 50mm Particle Board Screws (1).
9. Tighten the Particle Board Screws installed in Step #7.
Desktop
Wood Dowel
(5)
7 x 50mm
Particle Board Screw
(1)
Tighten the
Particle Board
Screws
To avoid damage and injury,
more than one person is
needed for assembly.
!CAUTION

10
Assembly (continued)
10. Attach the Left Side Panel (31) to the Desktop, Back Panel and Front Wiring Panel
using six Wood Dowels (5) and eight 7 x 50 mm Particle Board Screws (1).
11. Attach six Wiring Clamps (9) to the Back Panel using
six #10-16 x 3/4” Sheet Metal Screws (10).
Left Side
Panel
(31)
Wood Dowel
(5)
7 x 50mm
Particle Board Screw
(1)
#10-16 x 3/4”
Sheet Metal Screw
(10)
Wiring
Clamp
(9)

11
12. Attach the Left Fixed Tube (34) and Right Fixed Tube (35)
to the assembly using four 1/4-20 x 1.97 Machine Screws (17)
and 1/4-20 Cap Nuts (20) in each.
13. Attach the two Swivel Casters with Brakes (36)
to the front of the Workstation and
two Standard Swivel Casters (37)
to the Fixed Tubes using the supplied
Caster Wrench (15).
14. Push a 1-1/2” Plug (14) into the front of both Fixed Tubes.
Assembly (continued)
Left
Fixed Tube
(34)
1/4-20
Cap Nut
(20)
1/4-20 x 1.97
Machine Screw
(17)
Right
Fixed Tube
(35)
Standard Swivel
Caster
(37)
1-1/2”
Plug
(14)
Swivel Caster
with Brakes
(36)

12
Assembly (continued)
15. Attach seven Corner Brackets (6) to the Desktop, Side Panels and
Front Wiring Panel using #8 x 5/8” Pan Head Screws (4) in each.
16. Attach two Adjustable Keyboard Brackets (38)
to the bottom of the Desktop using
ve#10-16x3/4”SheetMetal
Screws (10) in each.
17. Tip the Assembly onto the Casters.
#8 x 5/8”
Pan Head Screw
(4)
Corner
Bracket
(6)
#10-16 x 3/4”
Sheet Metal Screw
(10)
Adjustable
Keyboard
Bracket
(38)

13
Assembly (continued)
18. If attaching the Optional Fixed Shelf (39):
a. Keep the narrower side of the Shelf at the same side as the Keyboard Brackets
(this leaves room for a computer tower on the wider side of the shelf).
b. Lay the Shelf onto the Frame Tubes and attach to the Side and Back Panels using
two Wood Dowels (5) at the back and eleven 7 x 50 mm Particle Board Screws (1).
7 x 50mm
Particle Board Screw
(1)
Optional
Fixed Shelf
(39)
Wood Dowel
(5)
Narrower side
Wider side

14
19. Attach the Flush Mount Handle (7) to the longer Wiring Access Door (40)
using two #8-18 x 3/8” Sheet Metal Screws (8).
20. Attach a Wiring Access Door (40) to each Set of hinges in the Back Panel
using two #6 x 3/4” Flat Head Screws (21).
Be sure that the screws are seated ush with the hinges.
Assembly (continued)
Flush Mount
Handle
(7)
5-Knuckle
Hinge
(3)
#8-18 x 3/8”
Sheet Metal Screw
(8)
Wiring Access
Door
(40)
#6 x 3/4”
Flat Head Screw
(21)
Wiring Access
Door
(40)

15
Assembly (continued)
21.AttachaSti󰀨ener(41)tothebottomonthebacksideofthePulloutPanel(42)
using three #8 x 5/8” Sheet Metal Screws (16).
22. Extend the Drawer Glides and attach one to each side of the Pullout Panel
using the included fasteners at all four locations.
23. Attach the Adjustable Keyboard Bottom Brackets to the Drawer Glides using
a #8-32 x 3/8” Self Tapping Screw (included with drawer glides) and
a 8-32 Hex Nut (24) on each side.
#8 x 5/8”
Sheet Metal Screw
(16)
Sti󰀨ener
(41)
Pullout Panel
(42)
Back side is
unnished
Front side has
edge banding
Holes can be used to secure
keyboard cables with the
included 4”Nylon Ties (25).
#8-18 x 3/8”
Sheet Metal Screw
(included with drawer glides)
8-32
Hex Nut
(22)
Drawer
Glide
Adjustable
Keyboard Bottom
Bracket
Use the included fasteners
at all four locations

16
Assembly (continued)
24. Fit the back of both Drawer Glides into the slots of the Front Wiring Panel.
Attach the Pullout Drawer to the Adjustable Keyboard Brackets using
one 1/4-20 x 1/2” Carriage Bolt (11), 1/4 x 47/64” Flat Washer (13)
and 1/4-20 Wing Nut (12) on each side.
It is preferred to face the smooth head of the Carriage Bolt
toward the inside as shown.
If space is limited, the Wing Nut and Washer can
face the inside but there may be an issue with snagging.
1/4-20
Wing Nut
(12)
1/4-20 x 1/2”
Carriage Bolt
(11)
1/4 x 47/64
Flat Washer
(13)
Fit Drawer Glides
into slots
Desktop is shown
removed for clarity.

17
Assembly (continued)
25. Attach Headphone Mount to the bottom of the Pullout Drawer using three
#10-16 x 3/4” Sheet Metal Screws (10).
Headphone Mount (43) can also be attached to the inside of the Right Side Panel.
26. Insert Grommets (2) into the Left, Right and Back Panels.
Headphone
Mount
(43)
#10-16 x 3/4”
Sheet Metal Screw
(10)
Grommet
(2)
Headphone Mount
can also be mounted
to the inside of the
Right Side Panel.

18
Optional Rackmount Shelf Assembly
If installing the Optional Rackmount Shelf Assembly, the smaller Wiring Access Door
and Hinges must be removed.
1. Clip the Cage Nuts into the front of each individual Rackmount Shelf.
10-32 x 3/4” Truss Screws are included to secure
electronic components into the Rackmount.
The deepest electronic components should be
installed at the bottom Rackmount Shelf.
2. Attach the Rackmount Shelf to the Desktop using six #8 x 5/8” Truss Head Screws.
If there are no existing pilot holes, a template must be used for placement.
3. Connect additional shelving units using six #10-32 x 3/8” Pan Head Screws
and 10-32 Jam Lock Nuts.
Cage
Nut
10-32 x 3/4”
Truss Screw
Rackmount
Shelf Unit
#8 x 5/8”
Truss Head Screw
If there are no pilot holes,
a template must be used
for placement.
10-32 x 3/8”
Pan Head Screw
10-32 x 3/8”
Jam Lock Nut

19
Optional Rackmount Shelf Assembly (continued)
4. Attach two 5-Knuckle Hinges to the top Rackmount Shelf using two #8-32 x 1/2” Flat Head Screws
and two #8-32 Nylon Lock Nuts in each.
Be sure that the screws are seated ush with the hinges.
5. Push/pull two Push-In Bumpers into the front
of the Rackmount.
 Trimo󰀨theexcesstailsusingasidecutterorscissors.
6. Clip the two Cage Nuts into the top at the front
of the Top Rackmount Shelf.
7. Attach the Top Panel to the Hinges using
two #6 x 3/4” Flat Head Screws in each Hinge.
Be sure that the screws are seated ush with
the hinges.
8. Close the Top Panel and secure it to the top Rackmount Shelf using
two #10-32 x 1.25” Pan Head Screws.
5-Knuckle
Hinge
#6 x 3/4”
Flat Head Screw
#10-32 x 1.25”
Pan Head Screw
Top Panel
Push-In
Bumper
#8-32 x 1/2”
Flat Head Screw
#8-32
Nylon
Lock Nut
Cage
Nut

20
This page is intentionally blank.