Wesco 260201 User manual

Page1of7
TABLE OF CONTENTS
1 General Information ............................................................................................................... 2
1.1 Description.....................................................................................................................2
1.2 Specifications.................................................................................................................2
2 Safety Information.....................................................................................................................2
3 Assembly.....………...................................................................................................................3
4 Operation.................................................................................................................................. 3
4.1 Braking............................................................................................................................3
4.2 Lifting.............................................................................................................................. 3
4.3 Lowering......................................................................................................................... 3
5 Maintenance..............................................................................................................................3
6 Part Information.........................................................................................................................4
6.1 Frame Part Diagram....................................................................................................... 4
6.2 Frame Part List............................................................................................................... 5
6.3 Pump Part Diagram........................................................................................................ 6
6.4 Pump Part List................................................................................................................ 7
WESCOINDUSTRIALPRODUCTS,INC
InstructionManual
FoldingHandleScissorsLiftTable
PartNumber: 260201
Note: Operator MUST read and understand these operating instructions before using
this Foldin
g
Handle Scissors Lift Table.

Page2of7
Folding Handle Scissors Lift Table
(Part # 260201)
Instruction Manual
ATTENTION: TO INSURE SAFE AND EASY USE OF YOUR SCISSORS LIFT TABLE,
READ THESE INSTRUCTIONS ENTIRELY BEFORE USING.
1. GENERAL INFORMATION
1.1 DESCRIPTION
Thank you for purchasing a Folding Handle Scissor Lift Table. These tables feature a lever
release handle, a chrome plated foot pedal and handle and a foot operated pump.
1.2 SPECIFICATIONS
Part Number 260201
Model LT-330SL
Capacity 330 lbs
Table Size 17.75” x 27.5”
Table Thickness .07”
Raised Height 28.5”
Lowered Height 8.5”
Caster Size 4” x 1”
Locking Caster Yes
Weight 98 lbs
Overall Width 17.75”
Overall Height 37”
Overall Depth 36”
Materials and specifications are subject to change without notice.
2. SAFETY INFORMATION
1) Read these instructions carefully before operation and get to know the performance and operation
requirements of the lift table.
2) Do not overload the hydraulic lift table. Overloading will cause damage to the hydraulic lift table.
3) It is forbidden for operators to stand or sit on the table during operation.
4) Do not insert hands or feet under the lowering table.
5) Brake the table when loading goods to prevent it from moving.
6) Off-set loading is forbidden when loading goods, goods should be distributed uniformly over the
table.
7) Loose or unstable goods are not permitted to be loaded.
8) The table can’t be moved when goods are being lifted.
9) The table can only be moved on flat and hard ground, do not use on sloped or rugged ground;
10) When putting goods on the table which has been hoisted, the weight of goods should be within
rated load.
Note: The safety valve only works in the hoisting process, if the table has been hoisted, and then
has overweight load on it, the safety valve will not work (also possibly damaging the unit).
11) When loading and unloading goods on hoisted table, don’t drag goods in cross direction, which
may cause serious off-set loading and make the table turn over.
12) When maintaining and repairing the table, the stand bar should be used to support fork arm in
order to prevent table from falling (there should be no load on the table).

Page3of7
Folding Handle Scissors Lift Table
(Part # 260201)
Instruction Manual
ATTENTION: TO INSURE SAFE AND EASY USE OF YOUR SCISSORS LIFT TABLE,
READ THESE INSTRUCTIONS ENTIRELY BEFORE USING.
3. DAILY INSPECTION
Daily inspection is effective to find any malfunction or fault on the lift table. Check the lift table for the
following before operation:
1) Check for any scratches, bending or cracking on the lift table.
2) Check if there is any oil leakage from the cylinder.
3) Check the vertical creep of the table.
4) Check the smooth movement of the wheels.
5) Check
the brake.
6) Check all bolts and nuts are tightened firmly.
CAUTION: Do not use lift table if any malfunction or fault is found.
4. OPERATION
4.1 Braking
CAUTION: Lift the brake when not moving it in order to prevent sudden movement.
The brake is equipped with the swivel caster on the right side.
1) Brake the wheel by pressing the brake pedal.
2) Release the brake by lifting up the brake pedal.
4.2 Lifting
Warning
1) Do not overload lift table. Stay within its rated capacity.
2) Do not side or end. Load must be distributed on at least 80% of table area.
Press the lifting pedal several times until the table reaches the desired position. The table does not
elevate after reaching the highest position even if the lifting pedal is pressed. The table lowers slightly
after reaching the highest position.
Model LT-330SL
Part Number 260201
Max Capacity (lbs) 330
Note: The hydraulic cylinder is designed to hold the table. The nature of hydraulic systems cause the
table to lower very slowly over an extended period of time. Please note the table does not stay at the
same position indefinitely.
4.3 Lowering
Warning: Do not put foot or hand in scissors mechanism
1) Rotating the knob lowers the table.
5. MAINTENANCE
5.1 Lubricate each point described below every month
5.2 Change hydraulic oil every 12 months.
Lubricating Points
1) Fitting of Cylinder – Oil
2) Roller Friction Surface – Grease
3) Link Pin – Oil
4) Pedal Fitting Point – Oil
5) Grease Nipple - Grease

Page4of7
Folding Handle Scissors Lift Table
(Part # 260201)
Instruction Manual
ATTENTION: TO INSURE SAFE AND EASY USE OF YOUR SCISSORS LIFT TABLE,
READ THESE INSTRUCTIONS ENTIRELY BEFORE USING.
6. PART INFORMATION
6.1 FRAME PART DIAGRAM

Page5of7
Folding Handle Scissors Lift Table
(Part # 260201)
Instruction Manual
ATTENTION: TO INSURE SAFE AND EASY USE OF YOUR SCISSORS LIFT TABLE,
READ THESE INSTRUCTIONS ENTIRELY BEFORE USING.
6. PART INFORMATION
6.2 FRAME PART LIST
Item Part
Number Item Description Qty. Item Part Number Item Description Qty.
1 260277 Handle Grip 1 29 Retaining Ring 1
2 Kit:
Handle
Release
Assembly
260250
Control Handle 1 30 Pin 1
3 Elastic Pin 1 31
4 Nut 1 32 Retaining Ring 2
5 Bolt with Hole 1 33 Connecting 1
6 Jacket 1 34 Cushion 1
7 Pull Line 1 35 Bolt 1
8 Long Shaft 1 36 Bushing 2
9 Spring 2 37 Cushion 1
10 Retaining Ring 3 38 Pedal Bar 1
11 Washer 2 39 Protecting Cover 1
12 Pin 4 40 Table 1
13 Bolt 8 41 Retaining Ring 4
14 Washer 8 42 Roller 4
15 Elastic Washer 8 43 Pin 2
16 Nut 8 44 Bushing 2
17 273636 Universal Wheel 2 45 Retaining Ring 2
18 Frame 1 46 Pin 1
19 Bolt 2 47 Retaining Ring 2
20 Kit: Front
Wheel
Assembly
273637
Washer 4 48 Fork Arm 1
21 Axle 2 49 Bushing 2
22/22A Bearing 4 50 Pin 2
23 Wheel 2 51 Retaining Ring 2
24 Nut 2 52 Elastic Pin 2
25 Pump Unit 1 53 Support Plank 2
26 Washer 2 54 Screw 2
27 Pin 1 55 Nut 2
28 Washer 1

Page6of7
Folding Handle Scissors Lift Table
(Part # 260201)
Instruction Manual
ATTENTION: TO INSURE SAFE AND EASY USE OF YOUR SCISSORS LIFT TABLE,
READ THESE INSTRUCTIONS ENTIRELY BEFORE USING.
6. PART INFORMATION
6.3 PUMP PART DIAGRAM

Page7of7
Folding Handle Scissors Lift Table
(Part # 260201)
Instruction Manual
ATTENTION: TO INSURE SAFE AND EASY USE OF YOUR SCISSORS LIFT TABLE,
READ THESE INSTRUCTIONS ENTIRELY BEFORE USING.
6. PART INFORMATION
6.4 PUMP PART LIST
Item Part
Number Item Description Qty. Item Part Number Item Description Qty.
260454 Complete Pump Replacement 1 230 Spring 1
201 Seal Washer 1 231 Spindle of Safety Valve 1
202 Pump Cylinder 1 232 Steel Ball 1
203 Dust Ring 1 233 O-Ring 1
204 Y-Seal 1 234 Seat of Pumping Valve 1
205 Pump Piston 1 235 Spindle of Pumping Valve 1
206 Spring 1 236 Spring 1
207 Spring Cap 1 237 Seal Washer 1
208 Retaining Ring 1 238
209 Joint Plate 2 239
210 Pin 1 240
211E Pump Body 1 241
212 Elastic Pin 1 242 Bolt 1
213 Spring 1 243 Seal Washer 1
214 Strike Pin 1 244E Retaining Ring 1
215 Seal Washer 1 245E Washer 1
216 Axle Sleeve 1 246E O-Ring 1
217 O-Ring 2 247E Cup Packing 1
218 Nut 1 248E Piston 1
219 Screw 1 249E O-Ring 1
220 Lever Plate 1 250E Piston Rod 1
221 Nut 1 251E Seal Washer 1
222 Elastic Washer 1 252E Cylinder Cap 1
223 Washer 1 253E O-Ring 1
224 Bolt with Hole 1 254E Dust Ring 1
225 Bolt with Hole 1 255 Plug 1
226 Nut 1 256 Liquid Throttle Sheath 1
227 Plug 1 257 Bolt 1
228 O-Ring 1 258E Sleeve 1
229 Adjusting Bolt 1
Find out more about service carts we have.