Weslo WLTL11310.0 User manual

USERʼS MANUAL
Model No. WLTL11310.0
Serial No.
Write the serial number in the
space above for future reference.
CAUTION
Read all precautions and instruc-
tions in this manual before using
this equipment. Save this manu-
al for future reference.
QUESTIONS?
If you have questions, or if parts are
damaged or missing, DO NOT CON-
TACT THE STORE; please contact
Customer Care.
IMPORTANT: Please register this
product (see the limited warranty
on the back cover of this manual)
before contacting Customer Care.
CALL TOLL-FREE:
1-866-699-3756
Mon.–Fri. 6 a.m.–6 p.m. MT
Sat. 8 a.m.–4 p.m. MT
ON THE WEB:
www.wesloservice.com
Serial
Number
Decal
www.weslo.com

2
WES O is a registered trademark of ICON IP, Inc.
TABLE OF CONTENTS
WARNINGDECA P ACEMENT ..............................................................2
IMPORTANTPRECAUTIONS .................................................................3
BEFOREYOUBEGIN .......................................................................5
ASSEMB Y ...............................................................................6
TREADMI OPERATION ....................................................................9
HOWTOFO DTHETREADMI .............................................................11
TROUB ESHOOTING ......................................................................12
EXERCISEGUIDE INES ...................................................................13
PART IST ...............................................................................14
EXP ODEDDRAWING .....................................................................15
ORDERINGREP ACEMENTPARTS ..................................................BackCover
IMITEDWARRANTY...............................................................BackCover
This drawing shows the location(s) of the warning decal(s). If a decal is missing or illegible, call the
telephone number on the front cover of this manual and request a free replacement decal. Apply
the decal in the location shown. Note: The decal(s) may not be shown at actual size.
WARNING DECAL PLACEMENT
(One on each side)

3
WARNING: To reduce the risk of serious injury, read all important precautions and
instructions in this manual and all warnings on your treadmill before using your treadmill. ICON
assumes no responsibility for personal injury or property damage sustained by or through the use
of this product.
IMPORTANT PRECAUTIONS
1. Before beginning this or any exercise pro-
gram, consult your physician. This is espe-
cially important for persons over age 35 or
persons with pre-existing health problems.
2. It is the responsibility of the owner to ensure
that all users of this treadmill are adequately
informed of all warnings and precautions.
3. Use the treadmill only as described.
4. Place the treadmill on a level surface, with at
least 8 ft. (2.4 m) of clearance behind it and 2
ft. (0.6 m) on each side. Do not place the
treadmill on any surface that blocks air open-
ings. To protect the floor or carpet from dam-
age, place a mat under the treadmill.
5. Keep the treadmill indoors, away from mois-
ture and dust. Do not put the treadmill in a
garage or covered patio, or near water.
6. Do not operate the treadmill where aerosol
products are used or where oxygen is being
administered.
7. Keep children under age 12 and pets away
from the treadmill at all times.
8. The treadmill should not be used by persons
weighing more than 250 lbs. (113 kg).
9. Never allow more than one person on the
treadmill at a time.
10. Wear appropriate exercise clothes when
using the treadmill. Do not wear loose
clothes that could become caught in the
treadmill. Athletic support clothes are recom-
mended for both men and women. Always
wear athletic shoes; never use the treadmill
with bare feet, wearing only stockings, or in
sandals.
11. Do not operate the treadmill if the treadmill is
not working properly. (See TROUBLESHOOT-
ING on page 12 if the treadmill is not working
properly.)
12. Always hold the handrails while using the
treadmill.
13. Do not attempt to raise or lower the treadmill
until it is properly assembled. (See ASSEM-
BLY on page 6 and HOW TO FOLD THE
TREADMILL on page 11.) You must be able to
safely lift 25 lbs. (11 kg) to raise or lower the
treadmill.
14. When folding the treadmill, make sure that
the storage latch is holding the frame secure-
ly in the storage position.
15. Do not change the incline of the treadmill by
placing objects under the treadmill.
16. Inspect and properly tighten all parts of the
treadmill regularly.
17. Never drop or insert any object into any
opening on the treadmill.
18. Servicing other than the procedures in this
manual should be performed by an autho-
rized service representative only.

4
19. Over exercising may result in serious injury
or death. If you feel faint or if you experience
pain while exercising, stop immediately and
cool down.
20. Do not place hands or feet under the tread-
mill while it is in use.
21. This treadmill is intended for in-home use
only. Do not use this treadmill in any com-
mercial, rental, or institutional setting.
22. The roller guards must be 1/8 inch from the
rear roller (see the drawing on page 5).
Adjust the roller guards, if necessary.
SAVE THESE INSTRUCTIONS

5
Handrail
Console
Hood
Walking Belt
Storage Pin
Adjustment Pin
Rear Roller Adjustment Bolts
Roller Guards
BEFORE YOU BEGIN
Thank you for selecting the new WES O®CARDIO
STRIDE 2.0 treadmill. The CARDIO STRIDE 2.0
treadmill offers a selection of features designed to
make your workouts at home more effective. And
when youʼre not exercising, the unique treadmill can
be folded up, requiring less than half the floor space of
other treadmills.
For your benefit, read this manual carefully before
using the treadmill. If you have questions after read-
ing this manual, please see the front cover of this
manual. To help us assist you, note the product model
number and serial number before contacting us. The
model number and the location of the serial number
decal are shown on the front cover of this manual.
Before reading further, please familiarize yourself with
the parts that are labeled in the drawing below.
Rear Roller

6
ASSEMBLY
To hire an authorized service technician to assemble the treadmill, call 1-800-445-2480. Assembly
requires only the included hex key and wrench .
Assembly requires two persons. Set the treadmill in a cleared area and remove all packing materials. Do not
dispose of the packing materials until assembly is completed. Note: Some small parts may have been
pre-assembled. To avoid damaging parts, do not use power tools for assembly. Extra hardware may be
included. The number in parentheses in the drawing below is the key number of the part, from the PART IST
near the end of this manual. The number after the parentheses is the quantity needed for assembly.
M8 Nylon
Nut (13)–4
M8 x 50mm Bolt
(38)–4
M5 x 10mm Bolt
(10)–2 M8 x 15mm Bolt
(33)–4 M8 Washer
(34)–4
M4 x 12mm
Screw (3)–2
M8 Curved
Washer (37)–4
38
13
13
37
37
38
Hole
Holes
Holes
1
1. Identify the Right Upright (36), which has a single hole
in the indicated location. (Note: There is a wire inside of
the eft Upright [35].) Hold the Right Upright against the
Base (14) as shown, and orient the Right Upright so the
two indicated holes are on the side shown.
Attach the Right Upright (36) to the Base (14) with two
M8 x 50mm Bolts (38), two M8 Curved Washers (37),
and two M8 Nylon Nuts (13) as shown. Make sure that
the curved sides of the Washers are against the Base.
Do not tighten the Nylon Nuts yet.
Attach the eft Upright (35) to the Base (14) in the
same way. Make sure that the eft Upright is oriented
so the two indicated holes are on the side shown. Do
not tighten the Nylon Nuts yet.
2. Raise the eft Upright (35) and the Right Upright (36) to
the position shown. 2
35 36
36
35
14
37
37

7
34
33
35
36
2
5
6
34
33
5. Hold the Handrail (5) near the eft and Right Uprights
(35, 36). Connect the Handrail Wire (2) to the Reed
Switch Wire (6). Insert the Wires down into the eft
Upright.
Attach the Handrail (5) to the Uprights (35, 36) with four
M8 x 15mm Bolts (33) and four M8 Washers (34). Be
careful not to pinch the Wires (2, 6).
See step 1. Tighten the four M8 Nylon Nuts (13).
5
3. Attach the Hood (28) to the front of the Frame (29) with
two M5 x 10mm Bolts (10). 3
10
10
28
29
4a
4. See drawing 4a. Hold the front of the Frame (29)
between the eft Upright (35) and the Right Upright
(36). Align the holes near the front of the Frame with
one of the two sets of adjustment holes in the Uprights.
Insert the two Adjustment Pins (4) into the holes in the
Uprights and the Frame. Make sure that the
Adjustment Pins are fully inserted at the same
height.
ook under the Frame (29) near the eft Upright (35).
See drawing 4b. ocate the Reed Switch Clip (11)
attached to the underside of the Frame. Insert the Reed
Switch (6) into the Clip as shown. Next, locate the
Magnet (12) on the left Flywheel (9). Turn the Flywheel
until the Magnet is aligned with the Reed Switch. Move
the Reed Switch so that there is a 1/8" (3 mm) gap
between the Reed Switch and the Magnet. Then,
tighten the M5 x 12mm Screw (44) in the Clip.
4
29
12
9
44
11
6
1/8 in.
View from
below
35
4b
29
36
4

8
1
27
Tab
6. The Console (1) requires two “AAA” batteries. Alkaline
batteries are recommended. Press the indicated tab on
the Battery Cover (27), and remove the Battery Cover.
Insert two batteries into the two battery clips; make
sure that the negative (–) ends of the batteries are
touching the springs in the battery clips.
9. Make sure that all parts are properly tightened before you use the treadmill. To protect the floor or car-
pet, place a mat under the treadmill.
Batteries
6
7. See drawing 7a. Hold the Console (1) near the
Handrail (5). Connect the wire on the Console to the
Handrail Wire (2). Attach the Console to the Handrail
with two M4 x 12mm Screws (3). Make sure that the
wires are not pinched.
See drawing 7b. Press the Battery Cover (27) back
onto the Console (1).
29
20
30
8. Remove the paper backing from the Adhesive Clip (30).
Press the Adhesive Clip onto the left side of the Frame
(29) in the indicated location. Press the Hex Key (20)
into the Adhesive Clip.
Make sure that the walking belt is properly tightened
(see SYMPTOM 3 on page 12).
8
27
3
11
2
7a 7b
5

9
STEP-BY-STEP CONSOLE OPERATION
Before the console can be operated, batteries must be
installed (see assembly step 6 on page 8). If there is a
thin sheet of plastic on the console, remove the plastic.
The console features six modes:
• Speed—This mode displays your speed, in miles
per hour.
• Distance—This mode displays the number of miles
you have walked.
• Time—This mode displays the elapsed time.
• Odometer—This mode displays the distance that
the walking belt has moved since the batteries
were changed.
• Calorie—This mode displays the approximate
number of calories you have burned.
• Scan—This mode displays the Speed, Distance,
Time, Odometer, and Calorie modes.
Follow the steps below to operate the console.
1. Turn on the power.
To turn on the power, press the console button or
begin walking. Note: If batteries were just installed,
the power will already be on. The first time you
use the treadmill, lubricate the walking platform
(see page 10).
2. Track your progress with the six modes.
When the power is turned on, the Scan mode will
be selected and the SCAN indicator will appear.
The console will display the Speed, Distance,
Time, Odometer,
and Calorie modes,
for about six sec-
onds each, in a
repeating cycle.
To select only the
Speed, Distance,
Time, Odometer, or Calorie mode, press the con-
sole button until only the SPEED, DIST, TIME,
ODO, or CA indicator appears in the display.
Make sure that the SCAN indicator does not
appear.
To reset all modes (except for the odometer
mode), press the console button for about three
seconds.
3. Turn off the power.
To turn off the power, simply wait for a few min-
utes. If the walking belt is not moved and the con-
sole button is not pressed for a few minutes, the
power will turn off automatically.
TREADMILL OPERATION
SCAN Indicator

10
INCLINE AD USTMENT
The incline of the treadmill can be adjusted to two
positions. Hold the front of the Frame (29), and
remove the two Adjustment Pins (4). Raise or lower
the Frame, align the holes in the Frame with one of
the sets of holes in the Uprights (35, 36), and then
reinsert the Adjustment Pins.
LUBRICATING THE WALKING PLATFORM
Before the treadmill is used, the walking platform
should be lubricated. Open the included lubricant
packet. Reach under one side of the walking belt as
far as you can, and apply half of the lubricant to the
walking platform. Then, reach under the other side of
the walking belt and apply the remaining lubricant.
After you have applied the lubricant, walk on the
treadmill for a few minutes to spread the lubricant.
CAUTION: Make sure that both
Adjustment Pins (4) are fully inserted at the
same height.
4
29
35 36
4
Apply lubricant here
Apply lubricant here