West Pond Enterprises MX-400TS User manual

MX-400TS User Guide
Software revision 1.17.3
West Pond Enterprises, LLC
6/28/2018

Confidential Page 1
Contents
Revision History ............................................................................................................................................3
Related documentation ................................................................................................................................3
Terms and terminology................................................................................................................................. 3
MX-400TS...................................................................................................................................................... 4
MX-400TS Option Modules....................................................................................................................... 4
MX-400TS Software ..................................................................................................................................4
Setting up the system ................................................................................................................................... 5
Unpacking the unit.................................................................................................................................... 5
Installing in the rack..................................................................................................................................5
Making the connections............................................................................................................................5
Power On .................................................................................................................................................. 6
Configuring the system .................................................................................................................................6
Front panel................................................................................................................................................ 6
Accessing the WebUI ................................................................................................................................ 7
Getting familiar with the MX-400 .................................................................................................................8
Overview ...................................................................................................................................................8
Sources......................................................................................................................................................9
Network Sources................................................................................................................................... 9
ASI ......................................................................................................................................................... 9
Video Server.......................................................................................................................................... 9
Outputs ...................................................................................................................................................10
ASI .......................................................................................................................................................11
Modulated RF Output .........................................................................................................................11
Program Mapping ...............................................................................................................................12
Oversubscribing the Transport ...........................................................................................................13
Display Controls ......................................................................................................................................13
Monitor ...................................................................................................................................................14
System.....................................................................................................................................................15
Settings................................................................................................................................................15
Accounts.............................................................................................................................................. 16
Log.......................................................................................................................................................16

Confidential Page 2
Info ......................................................................................................................................................16
Tools.................................................................................................................................................... 16
Appendix A –Quick Start Help....................................................................................................................17
Appendix B –FAQs......................................................................................................................................18
How do I create a TV channel from a video file? ................................................................................18

Confidential Page 3
Revision History
Date
Version
By
Description
12/1/2016
1.0.16
sdh
Update to 1.0.8
12/30/2016
1.0.18
sdh
Cleared out ST stuff
6/30/2017
1.4.0
sdh
Updated to latest rev. Monitor, video sources, etc.
5/17/2018
1.16.5
sdh
Total rewrite
6/5/2018
1.16.6
sdh
Fixed FlexDM port typo (should be 1194)
6/28/2018
1.17.3
sdh
Included FlexDM sync cloud icon. Updated RF output UI
Related documentation
Date
Version
By
Description
NA
1.15.1
sdh
User Guide, FlexStream MX-GS200, MD-100, RX-WP100
Terms and terminology
TS
MPEG2 Transport Stream
MPTS
Multi-program Transport Stream
Sources
Devices or software that generate MX-400 multiplexor Inputs
Inputs
TS traffic entering the multiplexor
Outputs
TS traffic exiting the multiplexor
Targets
Output devices receiving TS traffic from the multiplexor
Video Server
Feature of the MX-400 software that creates live program streams (TV
channels) from 1 or more TS files via a loop or scheduled event.
Video Wrapper
Feature of the MX-400 software that wraps video Inputs with HTML5
graphical content and then encodes it to make a program stream.
Monitor
Feature of the MX-400 software, included with a the RF modulator, which
scans the target RF plant for unused frequencies and monitoring used
frequencies.
Note: “MX-400”and “MX-400TS”are uses interchangeably in this document.

Confidential Page 4
MX-400TS
Thank you for purchasing the MX-400TS
professional multi-stream multiplexer
system. This product was designed for
professionals who need a tightly
integrated TS multiplexer for channel
picking, program conversion, edge
modulation, any other professional TS
conversion. This document should help
you get the MX-400TS up and running
quickly. For more information please
contact West Pond Enterprises sales or
support.
MX-400TS Option Modules
The MX-400TS multiplexor accepts TS sources from ASI and IP inputs and will output a TS to ASI, IP, and
Modulator target devices. The standard configuration is IP to IP. ASI inputs/outputs and modulators are
optional. Each 1U unit supports up to 8 modulated output channels and 4 ASI input/outputs.
MX-400TS Software
The MX-400TS software package is optimized for multiplexing and as such the MX-400 can process up to
500 mb/s of transport stream data. The maximum throughput is content dependent but there are no
software limits on the number of TS inputs or outputs supported. Special features include PSIP table

Confidential Page 5
merging, automated multicast IPTV channel discovery, a user friendly Web based UI, and front panel
video monitoring for all mux inputs. Supported TS sources include an integrated video server (TS file
spooling), TSoIP video/IPTV, RTSP (i.e. security cameras), and ASI. The multiplexer output can deliver
transports streams over IP, integrated multi-standard RF modulators, and/or ASI. SMPTE 2022
(proMPEG) FEC is available on all IP inputs and outputs.
Setting up the system
Unpacking the unit
The MX-400HY is a tightly integrated solution. The box is supplied with a power cable, and adapter
cables for the component, composite and S-Video connections.
Installing in the rack
The MX-400 is a standard 19” 1RU AV rack mounted (round hole) device. Air flow for cooling the
devices is moved from front to back and it can be used in slots adjacent to other devices. Mount the
device using 4 front panel screws, connect the power to the rear of the unit.
Making the connections
There are four Gigabit Ethernet ports on the back of the MX-400. These are independently configured
to support four unique LANs. Configure at least one of them as a management LAN from which you can
access the MX-400 Web UI. Others may be used to send/receive IPTV streams, access to cameras
(RTSP), or access to other assets
used by the MX-400.
While video source hot swap is
supported, this would be a good
time to connect up any AV sources
(HDMI, Component, HD-SDI, etc) to
the option module connections at
the rear of the unit.
The F connector marked M1 is the
monitor input. Connect this to your
in-house cable RF downstream of
any modulators, combiners
amplification, etc. Treat this
connection just as you would a TV.
This input will be used by the MX-
400 to detect unused frequencies on the in-house cable TV network.
The modulator outputs will be in the right hand option module bay. To merge the MX-400 channels
with existing in-house cable TV channels, connect the output F connectors to an RF combiner or
distribution network.

Confidential Page 6
Power On
Power on the MX-400 using the switch at the rear of the unit near the power receptacle. The blue LED
located at the center of the front panel will light immediately. Soon after this the two quarter VGA
screens will be illuminated. These screens will provide system status, real time video monitoring, and
basic system configuration.
Configuring the system
The MX-400 basic system
configuration is performed
using the front panel.
Software features are
configured using the MX-400
Web UI.
Front panel
Use the front panel of the MX-400 to check system status, configure each of the MX-400 network ports,
and reset the WebUI admin password. The main menu shows the System Name as configured in the
Web UI System/Settings page. Use the navigation pad to the right of the left screen to navigate the
menus. The Status screen provides information about the system including serial numbers, software
version, etc.
Navigate to the Network menu to configure each of the Network ports. Once the network port has been
correctly configured, and connected to the network, the network icon on the front screen should be
outlined in green. If not, check the connections at the rear of the device and the configuration screen
for errors. A black outline indicates the port is enabled but not functioning, a white outline indicates the
port is not enabled. When configuring the ports, one common error is mistaking N1 for N4, i.e. mentally
reversing the logical order of the network ports. These ports can also be configured using the Web UI.

Confidential Page 7
To set the MX-400 WebUI password to factory defaults, select “Reset Auth” from the system menu.
Use the CH up/down buttons to the left of the right screen to scroll through the video inputs configured
via the Web UI. The video monitoring screen shows a scaled replica of each enabled TS multiplexor
input. Use the up channel and down channel buttons to cycle through the video. This can be done at
any time and has no impact on the state of the system.
Accessing the WebUI
Using a computer that shares a LAN with the MX-400, point a web browser to the IP address to which
the MX-400 was set. You will be prompted to login. Use the
administrator credentials
User: Administrator
Password: admin
Note: Firefox and Chrome preferred.
There are three built-in users. The passwords for these users can be set by the administrator.
Administrator: Used by installer to configure and manage the system. This user has access to all
controls and settings.

Confidential Page 8
Operator: Used by less technical personal to access and change the video wrapper content. This
user can view nearly all settings but can only control those features that need to be changed during
a game or event.
Monitor: Read only access. Used by anyone who has an interest in the technology but should not be
making any configuration changes to the system.
Getting familiar with the MX-400
The West Pond product team may preconfigure your device to provide a head start for your particular
application. This may include the installation of template presentations, test videos, and the
configuration of input and output streams. The IP addresses used for IP inputs and outputs are likely
inappropriate for your installation and may need reconfiguring. In this section we will review how to
make small changes to these settings to get your system running as quickly as possible.
Overview
The top level page of the WebUI provides
an overview of the MX-400 scalable
multiplexor. The multiplexor combines
digital AV streams from a variety of
sources into groups and transmits them
with the correct signaling and timing to the
appropriate output. Outputs may have
constraints, such as bitrate and signaling,
that must be configured to operate
correctly. To preserve resources, inputs
are only processed if enabled. A mapping
between inputs and outputs is shown in the overview menu of the MX-400 WebUI. The sources (aka
enabled inputs) are shown on the left, outputs are shown on the right. The sources tab groups the
source transports by the input while the output tab shows this mapping grouped by destination
(output). There is a variety of information on these pages that can be valuable when trying to diagnose
a problem. Error indicators are shown when a problem has been detected with a particular input or
output stream. On the screen image above there is an error showing that the output transport is
oversubscribed. i.e. Utilization is over 100%. This should be rectified to avoid video artifacts.
Fingernail images captured from the video are periodically updated next to each input/output. This
helps to provide context when configuring your system. These update slowly so as to ensure they do
not steal any computational resources from the system.

Confidential Page 9
Sources
The Sources page shows how devices and IP
streams are enabled as inputs to the multiplexor.
Sources may include
network streams such as IPTV or an RTSP
feed from a security camera
the MX-400 internal video server
and ASI expansion modules.
Network Sources
Network sources are shown on the
Sources>Network tab. To add a network source, click “New Source”.
Specify a friendly name for the new source, this will be used on other
pages of this webUI. If subscribing to a multicast stream, specify the
multicast IP address –this is not required for unicast, specify the port,
and which interface the source is available on. If the source supports
SMPTE2022, then select this option. When everything is complete, click
create. If the networked source is RTSP, such as an RTSP security
camera, click on the RTSP tab and enter the name and URL of the
camera. i.e. rtsp://username:[e-mail]/stream1 Make sure the source is enabled
before saving.
ASI
ASI inputs are automatically detected and populated if available. These entries may be edited to change
the name or enable/disable as necessary.
Video Server
The Video Server creates TS streams from files uploaded to the MX-400 storage. The MX-400 does not
transcode these files dynamically, as such the TS files used by the video sever must be compatible with
both the target receiver and transport output. For example, if you were to create a stream for a US
CableTV QAM modulated output that stream should be MPEG2 (not h.264) encoded so that it is
compatible with the ATSC standard and can be used by ATSC TVs. West Pond provides a transcoding
web service, FlexDM, which simplifies the process of creating the appropriate files. Visit FlexDM.net for
more information.

Confidential Page 10
The “Content” tab shows the files that have been uploaded and may be used in any channel playlist.
Content with the icon are managed by the FlexDM service. The Channels tab shows the channels
created and the status of their playback. Create channels and upload content using the appropriate
buttons at the bottom of the screen. Once created TS files are assigned to a channel using the
button for looping playlists and the icon for scheduled content.
Outputs
An Output is a multiplexed TS output
which exits the MX-400 on a physical
transport such as a modulator, ASI port,
or Ethernet port. As this is a software
multiplexor, there is no specified limit to
the number of outputs. From a practical
perspective, it’s best to limit the
bandwidth consumed by the sum total of
all outputs to less than 500 Mb/s. The
multiplexor outputs are MPEG2
transport streams. Each MPEG TS output
must be specified and is shown on this
page. The software will automatically configure outputs for physical hardware such as modulators and
ASI ports. IPTV outputs, being virtual, must be added manually. New IPTV outputs are created by
clicking on the “Create Output” icon. Existing outputs can be deleted , modified (properties) ,
and mapped through the multiplexor (program mapping). The “create” and “modify” dialog boxes
are very similar.

Confidential Page 11
Give the output a friendly name. Keep in mind that this name will be used as the description if/when
you generate an m3u playlist. Next select UDP vs. RTP. UDP is raw UDP. The RTP protocol, which is also
transmitted using UDP, is more robust because the packets are numbered. Additional robustness can be
added using SMPTE2022 FEC, but this is only beneficial if the receiving device can utilize the FEC data.
The IP addresses and port fields are self-explanatory. Multicast addresses are supported. Specify the
interface you wish to bind this output to (N1, N2, N3 or N4). If you aren’t sure of the routing, check the
“System>Settings” page of this WebUI. The Data Rate used must be sufficient to contain the multiplex
transport that is being assigned to this output. If insufficient, clipping will occur and an error will be
shown on the Overview page. Nul stripping reduces the network traffic and is recommended for non
CBR applications. MPEG transport streams require signaling that is compatible with the transport and
targeting receiving devices. For example, if the IP output is feeding an edge QAM modulator for the US
market, select US Cable for signaling.
A playlist.m3u file that describes all of the multicast outputs can be downloaded
by clicking on the playlist icon. For IPTV networks, session announcement
protocol (SAP RFC 2974 ) is supported and included in the stream when enabled.
ASI
ASI inputs are automatically detected and populated if available. These entries may be edited to change
the name or enable/disable as necessary.
Modulated RF Output
The modulator hardware is automatically detected and a list of available modulators is shown on the
Output page of the WebUI. All modulators are expected to transmit over the same cable network, as
such it is not necessary to identify how a modulator maps to a particular F connector.

Confidential Page 12
To edit an RF output click on the associated config icon. Select the Channel from the list. It’s best
to be sure that the channel selected is not in use. If the
Channel/Frequency you wish to use is not on the list, you
may need to change the channel map. Select the
Modulator, the modulation standard, and the modulation
type. The power level should remain at 1 for most cabled
environments. When changing the power level, ALL
POWER LEVELS FOR RF OUTPUTS MUST BE THE SAME. To
ensure this, simply set each to the same number in the
Modify RF output dialog boxes. If a value greater than 1 is
required, attenuators may be necessary for TVs that are
receiving high power signals. Attenuators or amplifiers
should be used to achieve optimal power within the cable
distribution network. Use this field post install to make
minor power level adjustments if required.
Program Mapping
Program Mapping is the heart of the
multiplexor. Clicking on the icon for a
specific output will switch the Outputs page
to a program mapping view for that output.
Mapping an input to an output can be done
at the program level, or at the PID level. If
you are not intimately familiar with transport
stream anatomy, stick with the program level
and use the default setting whenever they
are provided.
Once in the Program Mapping view, all of the available multiplexor sources are listed on the left, each
with a mapping icon to the right. Click on the mapping icon and edit the mapping
appropriately for each program you would like included in this output. Programs included in the
transport are highlighted with a green background and a green arrow. On the “Modify program
mapping” dialog box, select “Yes” if you wish this source to be included in the output. Be mindful of the

Confidential Page 13
bandwidth limitations of your chosen output transport. If you oversubscribe, artifacts may occur on any
program in that transport. More on this topic
below. The Program Number field is used when
you wish to manually set the program number
for this program use this field. If not using the
“auto” selection for this field, be sure to choose
the program number carefully, there cannot be
any duplicate program numbers in a given
transport. The PMT pid and Elements are for
expert use only and should almost always be
“auto”. If the output is configured for US Cable
or ATSC, there are additional fields for PSIP
information. These fields contain data that is
often displayed on the TV when the channel is
first tuned. The Short Name can be up to 7
characters. i.e. WXYZ-12. The Virtual Channel
information will typically override the Physical
Channel information when displayed on a TV.
The Virtual Channel can be a single digit integer
or hyphenated if supplying both a major and minor channel number. You can return to this dialog later
and modify these fields at any time. All changes will take effect immediately. You may need to retune
the TV to see the results.
Oversubscribing the Transport
If the sum total bit rate for all the programs included the output multiplex is more than the specified
maximum bitrate for that transport, clipping will occur to ensure the output does not exceed the
maximum bitrate. Clipping means some packets are not transmitted. Missing packets will cause audio
and video artifacts in one or more of the programs included in that output transport. After selecting and
saving the programs that will be included in your output transport it is best to return to the Outputs tab
of the Overview page to see if the “Utilization” for that output is more than 100%. If it is, then the
number or mix of programs in that multiplex should be trimmed. At times, since video encoding is a
variable bitrate, these errors will be intermittent. To be save, it’s best not to exceed 90% of the
available bandwidth (“utilization”).
Display Controls
Display controls set the channel and
display state of a display that has
been provisioned with a West Pond
RX device such as the RX-WP100.
Each receiver must first be registered

Confidential Page 14
with the MX-400HY before it can receive commands. Select the “Displays” tab and click on
to start. Type in the Serial number located on the bottom of the RX device or via the
on screen display. Give the unit a friendly Name such as “Suite 202 hall”. Assign the device to a group,
or leave this for later if the group has not been created. Select the receiver Type and the Control
mechanism. Add notes if more information is necessary to identify the device. Click Register to
complete the registration. If a group was not assigned, select the Groups tab, create a group, and then
use the “Edit Device” icon to include the receiver in a group. Install the device at the display and
return to this menu item to exercise control.
Devices are typically controlled in groups. To control a device click on the “device state” icon. The
controls you see may vary depending upon the control capabilities of the connected device. When
controlling a group of devices, only the control states that are common to all devices in the group are
displayed in the control group dialog. As shown to the right, the power, channel, and volume can be
changed in this group. Select the new values and click save. The changes take immediate effect.
Monitor
The monitor page is used during
installation to detect unused
frequencies that the modulator
output can be configured to
use, and post install to visualize
the coax network usage and
health. The only configuration
setting is the channel map
chosen. The default is US Cable
TV. The monitor will tune to
each of the frequencies in the
chosen channel map and report the status. An empty row indicates an unused frequency. The caution
icon indicates the presence of some signal, perhaps noise or an unknown modulation. A used
frequency band will have a green signal icon. Frequency bands that are in use may also have
additional information if such information is available on the frequency. When selecting a frequency
band for the output modulator you will achieve the best results if you choose one that has no signal at
all. If none are available, one of the caution bands may be acceptable.

Confidential Page 15
System
The System page is used for configuring
and monitoring system level features of
the MX-400 system.
Settings
This page provides a more
comprehensive view into the system
configuration of the MX-400.
Network: The network configuration is
shown both here and on the front panel.
Changes may be made on either UI.
Click on the gear icon to configure
any one of the four network ports. Ports
configured and linked will have a green icon. Red icons indicate an error. No icon indicates the port is
disabled.
NTP: Use the icon to configure the network time server.
System Name: Use the icon to set the system name. This name will be displayed on the front panel
and on the webUI.
Timezone: Use the icon to set the timezone in which the server is being used. This is very
important when scheduling playback and other time critical WebUI features.
FlexDM remote management: West Pond’s
remote management allows authorized
personel to access the web UI of this, and
other West Pond devices, via a cloud hosted
web service. If authorized, West Pond can also
used this for support. Communications for this
feature utilize UDP port 1194 and TCP/IP port
443 for communication. All communications
are between the device and the flexdm.net
subnet. If the MX-400 has internet access and
this feature is enabled, green check marks
should exist on the Web UI next to Enabled,
Registered, and Online. If you wish to disable this feature, click on the gear and select Enabled/No.
The “Nonce” value is used during provisioning to identify this device and validate that it is in the hands

Confidential Page 16
of the owner. For more information on creating a FlexDM remote management contact West Pond
sales or technical support.
Accounts
There are three preconfigured accounts for managing the MX-400. This page allows the administrator
to set the passwords for these three accounts. Use the User pulldown to select the user and then enter
the new passwords. If you have lost your password, contact West Pond technical support for assistance
in accessing the device WebUI.
Log
The Log page provide insight into status changes and errors that may occur at both the system and
software level in the MX-400. This is most useful when presentations are not functioning as expected.
Check this log for clues. Note: Some warnings and errors may exist in the log during normal operation.
Info
Make, model, serial number, etc.
Tools
These are tools that are used to maintain
the system state.
System Config: You may export or import
the system configuration at any time. This
includes account information, the output
configuration, and network settings. It
does not currently export the provider
settings. Use this feature to archive your
settings and to clone devices for
distribution. Note: Configuration settings
are tied to software revision. You must
import a configuration file that was
exported from a system with the same
software revision.
License: The MX-400 software is keyed to the hardware. This tool is used to upgrade or otherwise
change the features provided with your MX-400 software.
Firmware: Use this tool to update the firmware of the MX-400. A software update will reboot the
system which can cause temporary anomalies in the output TS. Software updates are posted to the
West Pond ftp side. ftp://ftp.westpond.com Login: support, PW: flexstream
Reboot: If you wish to reboot the system. Rebooting the system can cause temporary anomalies in the
output TS.

Confidential Page 17
Appendix A –Quick Start Help
This section is provided to enable installers with a check list of things to do when installing the system.
1) Mount the device and make all the required connections. Power the system on. For more
information follow the instruction above in the section: Setting up the system.
2) Use the front panel to configure the network interfaces. See Configuring the system for more
information on this topic
3) Enable and configure Sources to the multiplexer. You need not configure them all at this point.
You can easily add more later.
a. Sources may include IPTV, RTSP cameras, or the Video Server
b. Details for each are provide in the Sources section of the main document.
c. When configuring the Video Server, be sure that your TS files are compatible with the
devices receiving the output of the MX-400HY. For example, if using and ATSC
modulated output you must use MPEG2 encoded files. ATSC devices will not decode
h.264 video.
d. If enabling the Video Server source, try one of the preloaded MPEG2 or h.264 files
before loading your own.
e. All of the enabled multiplexer inputs can be viewed on the front panel and Overview
page of the WebUI. Use this to verify you have correctly configured your inputs.
4) Enable and configure Outputs of the multiplexer.
a. Outputs may include IPTV or RF.
b. Create Outputs first, then select the “Program Mapping” icon to configure their
contents.
c. When creating an RF output, utilize the Monitor page to find unused carrier frequencies.
d. When selecting the “Program Mapping” be sure of the following:
i. All of the sources selected are compatible with the receiving device. i.e. If ATSC,
all of the included program streams should be MPEG2 encoded video.
ii. The sum of all enabled sources should not exceed the maximum bitrate of the
Output transport. i.e. If ATSC 8-VSB do not exceed 19.39 Mb/s. Check the
outputs tab of the overview page to see signs of over subscription.
5) Check the results
a. All multiplexer video sources should be visible on the front panel and Overview page of
the WebUI.
b. Have a receiving device ready to test the results.

Confidential Page 18
Appendix B –FAQs
How do I create a TV channel from a video file?
Video files can be transcoded into TS files that can then be sources to the MX-xxx multiplexor and
transmitted over any of the multiplexor outputs. The steps to creating a channel from a video files are:
1) Transcode the video file into a TS file that is suitable for your output transport and receiving
devices. (bitrate, encoding, resolution)
2) Download the file to the MX-xxx storage
3) Create a Video Server streaming video channel
4) Include the transcoded file in the channel playlist
5) Modify the multiplexor Output to include the Video Server channel
Step 1 & 2: Transcode
Transcoding is the most complicated step toward creating your own video server channel. We strongly
encourage using the FlexDM service to ensure that the resulting file is both compatible and optimal for
the chosen transport and receivers. The FlexDM.net web service allows you to manage devices and
upload videos that will be transcoded and downloaded to the device directly. Log in to FlexDM.net to
create an account and start managing your video streams. Then skip to Step 3.
Alternatively, if the file has already been transcoded, it is possible to upload the TS file directly to the
MX-xxx device via the WebUI. To do so, select the Sources/Video Server tab and click on “Upload
Content”. Complete the dialog box and
click “upload”. When the upload is
complete, the new file will appear in the
“Content”table as shown below. Note
the bitrate of the file. The maximum
bitrate of any file in the Play List (see below) will determine the minimum amount of bandwidth
reserved in the transport. If using FlexDM, the files will appear on “Content” table shortly after the
upload to FlexDM is complete.
Step 3: Create Video Server Channel
Create the Video Server Source Channel by clicking on the “Create Channel” button in the “Channels”
tab as shown below. Complete the form and click “Create”. A line for this new channel will appear in
the “Channels” table.

Confidential Page 19
Step 4: Add to Playlist
Click on the icon on the Channel table entry for which you wish to create a Channel play list. (See
image above) The playlist is an ordered list of video files. All of the files in a Play List must be compatible
with the Output transport and TV receiver. It is also good practive to ensure the files are similar in
bitrate. For example, do not mix MPEG2 and h.264 videos on the same Output unless you are sure the
receiver can decode both. Additionally, do
not add a 20 Mb/s file on the same playlist
where the others were all 10 Mb/s and the
Output bitrate cannot support an additional
20 Mb/s. Doing so will oversubscribe the
transport and show an error in the Overview
Output screen.
Add files to the play list by selecting the file
and clicking “+ Add to Playlist”. Then
position the file in the play order using the
up/down arrows. The same file may be
added more than once. Click “Save” when
done.
You can also schedule files to playback at a particular
time of day. To do this click on the icon. This
will display the “Schedule” dialog. Scheduled
playback overrides the playlist entry for the period in
which it is played. Make sure the time and time
zone of the system matches the time and time zone
of the PC from which you are viewing the WebUI. If
not, adjust accordingly.