Westermo ODW-730-F2 User manual

www.westermo.com
ODW-730-F2
Fibre Optic Modem
Industrial Converter RS-485 to Fibre Optic Link
Repeater, line and redundant ring

26651-2251

3
6651-2251
General information
Legal information
The contents of this document are provided “as is”. Except as required by applicable law,
no warranties of any kind are made in relation to the accuracy and reliability or contents
of this document, either expressed or implied, including but not limited to the implied
warranties of merchantability and fitness for a particular purpose. Westermo reserves
the right to revise this document or withdraw it at any time without prior notice.
Under no circumstances shall Westermo be responsible for any loss of data or income or
any special, incidental, and consequential or indirect damages howsoever caused.
More information about Westermo can be found at www.westermo.com

46651-2251
Safety and Regulations
Warning signs are provided to prevent personal injury and/or damages to the product.
The following levels are used:
Level of warning Description Consequence
personal injury
Consequence
material damage
WARNING
Indicates a potentially
hazardous situation
Possible death or
major injury
Major damage to the
product
CAUTION
Indicates a potentially
hazardous situation
Minor or moderate
injury
Moderate damage to
the product
NOTICE
Provides information
in order to avoid
misuse of the
product, confusion or
misunderstanding
No personal injury Minor damage to the
product
NOTE
Used for highlighting
general, but important
information
No personal injury Minor damage to the
product

5
6651-2251
Before installation:
Read this manual completely and gather all information on the product. Make sure that
you understand it fully. Check that your application does not exceed the safe operating
specifications for this product.
WARNING - SAFETY DURING INSTALLATION
The product must be installed by qualified service personnel
and built in to an apparatus cabinet or similar, where access is
restricted to service personnel only.
WARNING - HAZARDOUS VOLTAGE
Do not open an energized product. Hazardous voltage may occur
when connected to a power supply.
WARNING - PROTECTIVE FUSE
It must be possible to disconnect manually from the power supply.
Ensure compliance to national installation regulations. Replacing
the internal fuse must only be performed by Westermo qualified
personell.
CAUTION - CLASS 1 LASER PRODUCT
Do not look directly into a fibre optical port or any connected
fibre, although the product is designed to meet the Class 1 Laser
regulations and complies with 21 CFR 1040.10 and 1040.11.
CAUTION - ELECTROSTATIC DISCHARGE (ESD)
Prevent electrostatic discharge damages to internal electronic
parts by discharging your body to a grounding point (e.g. use a
wrist strap).

66651-2251
Care recommendations
Follow the care recommendations below to maintain full operation of product and to
fulfill the warranty obligations:
• Do not drop, knock or shake the product. Rough handling above the specification
may cause damage to internal circuit boards.
• Use a dry or slightly water-damp cloth to clean the product. Do not use harsh
chemicals, cleaning solvents or strong detergents.
• Do not paint the product. Paint can clog the product and prevent proper operation.
If the product is used in a manner not according to specification, the protection provided
by the equipment may be impaired.
If the product is not working properly, contact the place of purchase, nearest Westermo
distributor office or Westermo technical support.
Product disposal
This symbol means that the product shall not be treated
as unsorted municipal waste when disposing of it. It needs
to be handed over to an applicable collection point for
recycling electrical and electronic equipment.
By ensuring this product is disposed of correctly, you will
help to reduce hazardous substances and prevent potential
negative consequences to both environment and human
health, which could be caused by inappropriate disposal.
Cleaning of the optical connectors
In the event of contamination, the optical connectors should only be cleaned by the use
of recommended cleaning fluids and correct cleaning equipment.
Recommended cleaning fluids:
• Methyl-, ethyl-, isopropyl- or isobutyl-alcohol
• Hexane
• Naphtha
CAUTION - HANDLING OF SFP TRANSCEIVERS
SFP transceivers are supplied with plugs to avoid contamination
inside the optical port. They are very sensitive to dust and dirt. If
the fibre is disconnected from the product, the protective plugs
on the transmitter/receiver must be connected. The protective
plugs must be kept on during transportation. The fibre optics
cables must be handled the same way.

7
6651-2251
FCC Part 15.105
Notice:
This equipment has been tested and found to comply with the limits for a Class A digi-
tal device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference when the equipment is operated in a
commercial environment.
This equipment generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instruction manual, may cause harmful interfer-
ence to radio communications. Operation of this equipment in a residential area is likely
to cause harmful interference in which case the user will be required to correct the
interference at his own expense.
Agency approvals and standards compliance
Type Approval / Compliance
EMC EN 61000-6-1, Immunity residential environments
EN 61000-6-2, Immunity industrial environments
EN 61000-6-3, Emission residential environments
EN 61000-6-4, Emission industrial environments
EN 50121-4, Railway signalling and telecommunications apparatus
IEC 62236-4, Railway signalling and telecommunications apparatus
DNV Standard for Certification no. 2.4
Safety UL/CSA 60950-1, IT equipment
Declaration of Conformity
Hereby, Westermo declares that this product is in compliance with applicable EU direc-
tives and UK legislations. The full declaration of conformity and other detailed informa-
tion is available at www.westermo.com/support/product-support.

86651-2251
Type tests and environmental conditions
Electromagnetic Compatibility
Phenomena Test Description Level
ESD EN 61000-4-2 Enclosure contact ± 6 kV
Enclosure air ± 8 kV
RF field AM modulated IEC 61000-4-3 Enclosure 10 V/m 80% AM (1 kHz), 80 – 800 MHz
20 V/m 80% AM (1 kHz), 800 – 1000 MHz
20 V/m 80% AM (1 kHz), 1400 – 2700 MHz
RF field 900 MHz ENV 50204 Enclosure 20 V/m pulse modulated 200 Hz, 900 ± 5 MHz
Fast transient EN 61000-4-4 Signal ports ± 2 kV
Power ports ± 2 kV
Surge EN 61000-4-5 Signal ports unbalanced ± 2 kV line to earth, ± 2 kV line to line
Signal ports balanced ± 2 kV line to earth, ± 1 kV line to line
Power ports ± 2 kV line to earth, ± 2 kV line to line
RF conducted EN 61000-4-6 Signal ports 10 V 80% AM (1 kHz), 0.15 – 80 MHz
Power ports 10 V 80% AM (1 kHz), 0.15 – 80 MHz
Pulse Magnetic field EN 61000-4-9 Enclosure 300 A/m, 6.4 / 16 µs pulse
Mains freq. 50 Hz EN 61000-4-16 Signal ports 100 V 50 Hz line to earth
Mains freq. 50 Hz SS 436 15 03 Signal ports 250 V 50 Hz line to line
Radiated emission CISPR 16-2-3 Enclosure EN 61000-6-3
ANSI C63.4 FCC part 15
Conducted emission CISPR 16-2-1 AC power ports EN 61000-6-3
ANSI C63.4 AC power ports FCC part 15
CISPR 16-2-1 DC power ports EN 61000-6-4
Dielectric strength UL 60950 Signal port to all other
isolated ports
2 kVrms 50 Hz 1min
Power port to other
isolated ports
3 kVrms 50 Hz 1min
2 kVrms 50 Hz 1min (@ rated power < 60V)
Environmental
Temperature EN 60068-2-1
EN 60068-2-2
Operating –40 to +60°C
Storage & Transport –40 to +60°C
Maximum surface
temperature
135ºC (temperature class T4)
Humidity EN 60068-2-30 Operating 5 to 95% relative humidity
Storage & Transport 5 to 95% relative humidity
Altitude Operating 2 000 m / 70 kPa
Service life Operating 10 year
Vibration IEC 608-2-6 Operating 7.5 mm, 5 – 8 Hz
2 g, 8 – 500 Hz
Shock IEC 60068-2-27 Operating 15 g, 11 ms
Packaging
Enclosure UL 94 PC / ABS Flammability class V-1
Dimension W x H x D 35 x 121 x 119 mm
Weight 0.26 kg
Degree of protection IP21
Cooling IEC 529 Enclosure Convection
Mounting Horizontal on 35 mm DIN-rail

9
6651-2251
Functional description
OVP Over Voltage Protection
OCP Over Current Protection
Converter serial interface – optical fibre
ODW-730 is a fibre optic modem that converts between electrical RS-485 and a fibre
optical link.
ODW-730 can also be used to convert from RS-485 to RS-232 by using a ODW-730 in
the same link as ODW-720.
Repeater – optical fibre links
ODW-730 is a fibre optic repeater that repeats received data from one fibre link out to
the other link. This is useful e.g. for long distance communication, where electromagnetic
interference may occur or when isolation of the electrical network is needed. The
maximum optical fibre distance depends on selected fibre transceiver and fibre type.
Distances up to 80 km (50 miles) are available.
STATUS
C
NO
NC
LED’s
Switches
CH 2
SFP
Fibre transceiver
TX
RX
CH 1
SFP
Fibre transceiver
TX
RX
I
nternal
E
lectronics
ODW-730
COM
COM
+VA
O
V
P
+VB
POWER
T
/R-
T/R+
RS -485
R
-
R+
+5V
0V
+5V
0V
O
C
P
O
V
P

10 6651-2251
Interface specifications
Power
Rated voltage 12 to 48 VDC and 24 VAC
Operating voltage 10 to 60 VDC and 20 to 30 VAC
Rated current 400 mA @ 12 V
200 mA @ 24 V
100 mA @ 48 V
Rated frequency DC and 48 to 62 Hz
Inrush current I²t 0.2 A²s
Startup current* 1.0 Apeak
Polarity Reverse polarity protected
Redundant power input Ye s
Isolation to RS-485 and Status port
Connection Detachable screw terminal
Connector size 0.75 – 2.5 mm² (AWG 18 – 13)
Connect the unit using at least 18 AWG (0.75 mm2) wiring
Shielded cable Not required
* External supply current capability for proper startup
Status
Port type Signal relay, changeover contacts
Rated voltage Up to 48 VDC
Operating voltage Up to 60 VDC
Contact rating 500 mA @ 48 VDC
Contact resistance < 50 mW
Isolation to RS-485 and Power port
Connection Detachable screw terminal
Connector size 0.2 – 2.5 mm² (AWG 24 – 13)
Shielded cable Not required
Branch circuit protection (fuse) is required for this unit with rating not exceeding 20 A.
Product should be connected to UL Listed power supplies rated 12 – 48 VDC, min 500
mA or 24 VAC, min 500 mA or reliably grounded DC SELV source.

11
6651-2251
RS-422/485
Electrical specification EIA RS-485, 2-wire or EIA RS-422 4-wire twisted pair
Data rate 300 bit/s – 1.5 Mbit/s
Data format 9 – 12 bits
Protocol Start-bit followed by 8-11 bits
Retiming Ye s
Turning time
(2-wire RS-485)
One tbit
tbit = 1 / Baud rate (Baud rate in bit/s)
Transmission range < 1200 m, depending on data rate and cable type (EIA RS-485)
Settings 120 Wtermination and failsafe biasing 680 W
Protection Installation Fault Tolerant (up to ±60 V)
Isolation to Status and Power port
Connection Detachable screw terminal
Connector size 0.2 – 2.5 mm² (AWG 24 – 13)
Shielded cable Not required

12 6651-2251
Location of Interface ports, LED’s and DIP-switches
ODW-730-F2
Position Direction* Description Product
marking
1 In Common voltage COM
2 In Voltage A +VA
3 In Voltage B +VB
4 In Common voltage COM
Power
screw terminal
LED Indicators
Position Description Product
marking
1Contact with C when fibre optical
links are in operation
NO
2 Common C
3Open (no contact with C)
when fibre optical links are
in operation
NC
Status
screw terminal
Position Direction* Description Product
marking
1 In R+ (EIA RS-485 A’) R+
2 In R– (EIA RS-485 B’) R–
3 In/Out T+ (EIA RS-485 A) T/R+
4 In/Out T– (EIA RS-485 B) T/R–
RS-422/485
screw terminal
* Direction relative this unit
FX(Fibre)
DIP-switches accessible under lid

13
6651-2251
LED indicators
LED Status Description
PWR
Power
ON Power is on.
OFF Power is off.
FP ON Focal point
OFF Redundant ring member or multidrop
unit.
CH 2
Channel 2 link status
ON Fiber link to other unit has been
established at CH 2.
Flashing Optical power detected but link to other
unit has not been established at CH 2.
OFF No optical power detected and no link
to other unit has been established at
CH 2.
CH 1
Channel 1 link status
ON Fiber link to other unit has been
established at CH 1.
Flashing Optical power detected but link to other
unit has not been established at CH 1.
OFF No optical power detected and no link
to other unit has been established at
CH 1.
TD Flash Data received on the electrical interface
and transmitted out on the optical inter-
face.
OFF No data received on the electrical
interface.
RD Flash Data received on the optical interface
and transmitted out on the electrical
interface.
OFF No data received on the optical interface.
FL R
Failure link remote
ON Remote fibre link failure.
A fibre link is out of operation at any
other unit than this one.
Flashing Hardware error or invalid configuration.
FL L
Failure link local
ON Local fibre link failure.
A fibre link is out of operation at this
unit.
Flashing Hardware error or invalid configuration.
Note: During power up, all LED’s will turn on for about 1 second.

14 6651-2251
CAUTION - ELECTROSTATIC DISCHARGE (ESD)
Prevent electrostatic discharge damages to internal electronic
parts by discharging your body to a grounding point (e.g. use a
wrist strap).
S1 DIP-switch, asynchronous mode speed selection
ON
1 2 3 4 5 6 7 8
300 bit/s
ON
1 2 3 4 5 6 7 8
57.6 kbit/s
ON
1 2 3 4 5 6 7 8
1.0 Mbit/s
ON
1 2 3 4 5 6 7 8
1200 bit/s
ON
1 2 3 4 5 6 7 8
115.2 kbit/s
ON
1 2 3 4 5 6 7 8
1.5 Mbit/s
ON
1 2 3 4 5 6 7 8
2400 bit/s
ON
1 2 3 4 5 6 7 8
125 kbit/s
ON
1 2 3 4 5 6 7 8
9 bits data
format
ON
1 2 3 4 5 6 7 8
4800 bit/s
ON
1 2 3 4 5 6 7 8
187.5 kbit/s
ON
1 2 3 4 5 6 7 8
10 bits data
format
ON
1 2 3 4 5 6 7 8
9600 bit/s
ON
1 2 3 4 5 6 7 8
230.4 kbit/s
ON
1 2 3 4 5 6 7 8
11 bits data
format
ON
1 2 3 4 5 6 7 8
19.2 kbit/s
ON
1 2 3 4 5 6 7 8
250 kbit/s
ON
1 2 3 4 5 6 7 8
12 bits data
format
ON
1 2 3 4 5 6 7 8
38.4 kbit/s
ON
1 2 3 4 5 6 7 8
500 kbit/s
Supervision table when selecting data format
Start bit ……………………
7 bit … … … …
8 bit … … … …
Parity … … … …
1 stop bit … … … …
2 stop bit … … … …
Number of bit 9 10 10 10 11 11 11 12
S2S1
S3
DIP-switch settings

15
6651-2251
S1 DIP-switch, synchronous mode time frame selection
ON
1 2 3 4 5 6 7 8
1.6 ms
ON
1 2 3 4 5 6 7 8
13 µs
ON
1 2 3 4 5 6 7 8
2 µs
ON
1 2 3 4 5 6 7 8
416 µs
ON
1 2 3 4 5 6 7 8
8.6 µs
ON
1 2 3 4 5 6 7 8
1 µs
ON
1 2 3 4 5 6 7 8
208 µs
ON
1 2 3 4 5 6 7 8
4.3 µs
ON
1 2 3 4 5 6 7 8
500 ns
ON
1 2 3 4 5 6 7 8
104 µs
ON
1 2 3 4 5 6 7 8
4 µs
ON
1 2 3 4 5 6 7 8
300 ns
ON
1 2 3 4 5 6 7 8
52 µs
ON
1 2 3 4 5 6 7 8
2.6 µs
ON
1 2 3 4 5 6 7 8
26 µs
ON
1 2 3 4 5 6 7 8
2.1 µs
S1 DIP-switch / Description V/Y mode
ON
1 2 3 4 5 6 7 8
Y-mode
ON
1 2 3 4 5 6 7 8
V-mode
OR
OR
OR
channel 1channel 2
RS-485
If both fibre channels 1 and 2 are used
and not redundant ring focal point
If only fibre channel 1 is used or
if redundant ring focal point
If only fibre channel 2 is used
channel 1
channel 1
channel 1
channel 2
RS-485
RS-485
RS-485
channel 2
channel 2
OR
For applications that only require half duplex communication it is recommended to use
Y-mode. Please see the ODW-730 Management Guide for further details.

16 6651-2251
S2 DIP-switch
ON
1 2 3 4 5 6 7 8
RS-485
2-wire
ON
1 2 3 4 5 6 7 8
Use secondary data channel.
ON
1 2 3 4 5 6 7 8
RS-422
4-wire
ON
1 2 3 4 5 6 7 8
Single channel system redundant
ring. E.g. only the primary or
secondary channel is used.
ON
1 2 3 4 5 6 7 8
Multidrop mode.
ON
1 2 3 4 5 6 7 8
Dual channel system redundant ring.
E.g. both the primary and secondary
channel are used simultaneously.
ON
1 2 3 4 5 6 7 8
Redundant ring mode.
ON
1 2 3 4 5 6 7 8
Set status port on both local fibre
link (FL L) and remote fibre link (FL
R) errors.
ON
1 2 3 4 5 6 7 8
Multidrop mid unit or Redundant
ring member.
ON
1 2 3 4 5 6 7 8
Set status port on local fibre link
(FL L) error only.
ON
1 2 3 4 5 6 7 8
Multidrop end unit. Redundant ring
focal point.
ON
1 2 3 4 5 6 7 8
S2:7 has no function
ON
1 2 3 4 5 6 7 8
Use primary data channel.
ON
1 2 3 4 5 6 7 8
Always OFF
S3 DIP-switch
No termination and fail-safe
Termination with fail-safe (4-wire)
Termination with fail-safe (2-wire)
ON
1 2 3 4
ON
1 2 3 4
ON
1 2 3 4
Factory default
ON
1 2 3 4 5 6 7 8
S1
ON
1 2 3 4 5 6 7 8
S2

17
6651-2251
RS-485 termination at system level
The system should be installed in according to the RS-485 specification. A system should
always form a bus structure where the termination is at the end points of the bus. See
diagrams for details of how this is done with RS-485 2-wire and 4-wire.
N.B. R+/R–, T+/T– definitions are not standard, it can help to shift + and – if the unit
does not work.
=Termination
ODW-730 Series
Slave unit Slave unit Slave unit
ODW-730 Series
Slave unit Slave unit Slave unit
Max 0.3 metre
=Termination
T/R+
T/R–
T/R+T/R– T/R+T/R– T/R+T/R–
R+
R–
T+
T–
R– R+ R+T– T– R– R+ T– T+T+T+ R–

18 6651-2251
About the interfaces
Power terminal
The power terminal has two independent inputs, +VA and +VB, allowing redundancy
should either fail. The ODW-730 power supply is galvanically isolated from all other
internal electronics.
Optical fibre interfaces
ODW-730 uses Small From Factor Pluggable (SFP) transceivers that are in compliance
with the Multi-Sourcing Agreement (MSA). This means that a wide range of different fibre
tranceivers and connectors can be used.
RS-485 interface
A 4 position detachable screw terminal that can handle full duplex data rates up to 1.5
Mbit/s and can be set to either 2- or 4-wire RS-485 system.
When 4-wire RS-485 is selected, the terminals T/R+ and T/R– will always be set to
transmit and terminals R+ and R– will always receive data. Manchester coded protocol
can be tranferred with Synchroous mode.
Status port
The status port connects to an internal relay wich may be used to trigger an external
alarm if a fault condition occurs. During normal operation pins 1 and 2 are in contact
with each other, and pins 2 and 3 are isolated. During an optical link failure, or power
failure, pins 1 and 2 are isolated, and pins 2 and 3 are in contact with each other.
Optical link failures can be classified in to two categories, local or remote, as indicated
by the FL L and FL R LED’s. A local link failure is when an optical link is down at this
particular unit. A remote link failure is when an optical link is down at some other unit.
From the factory, the status port is set to trigger on both types of link failures. However,
by setting DIP-switch S2:6 to the ON position, the status port will only trigger when a
local link failure has occured.

19
6651-2251
Cooling
This unit uses convection cooling. To avoid obstructing the air-
flow around the unit, use the following spacing rules. Minimum
spacing 25 mm (1.0 inch) above /below and 10 mm (0.4 inches)
left /right the unit. Spacing is recommended for the use of unit
in full operating temperature range and service life.
Removal
Press down the black support at the top of the unit. See figure.
Mounting
This unit should be mounted on 35 mm DIN-rail, which is
horizontally mounted inside an apparatus cabinet, or similar.
Snap on mounting, see figure.
CLICK!
CLICK!
10 mm *
(0.4 inches)
25 mm
25 mm
* Spacing (left/right) recommended for
full operating temperature range

20 6651-2251
Referring documents
For detailed information on how to configure the ODW-730-F2 for different applications.
Type Description Document number
Management Guide Management Guide ODW-730-F2 6651-2255