Westgate LF4PRO-50-150W-MCTP Service manual
INSTALLATION INSTRUCTION MANUAL
LED FLOOD LIGHT, 100-277VAC
SERIES:
LF4PRO-50-150W-MCTP
Model number parameter list:
Item Model Input Voltage Power
Factor Watt Input Current
≥0.9
ALF4PRO-50-150W-MCTP 100-277VAC 50/60HZ
50W
80W
100W
150W
1.8A
1. Introduction
This LED Flood light uses the latest in solid state lighting technology for long life, low
maintenance, and high efficiency.
The same as traditional HID lighting. There are two installation methods, suitable for various
occasion.
An internal power-factor-corrected switch-mode supply allows it to be used from
any nominal 100-277VAC, 50/60Hz supply without any variation in light output.
Suitable for use in the following locations:
•
Ambient Temp: -40~+122°F
•
Wet Locations
Note: Save these instructions for future reference.
2. Installation
For supply connections use wire rated for at least 90°C
Warning:
To avoid the risk of fire, explosion, or electric shock, this product should be installed,
inspected, and maintained by a qualified electrician only, in accordance with all applicable
electrical codes.
Warning:
To avoid electric shock:
•Be certain electrical power is OFF before and during installation and maintenance.
•Luminaire must be connected to a wiring system with an equipment-grounding conductor.
Warning:
To avoid explosion:
•Make sure the supply voltage is the same as the rated luminaire voltage.
•Do not install where the marked operating temperatures exceed the ignition temperature
of the hazardous atmosphere.
•Do not operate in ambient temperatures above those indicated on the luminaire
nameplate.
•Keep lens tightly closed when in operation.
Warning:
THIS PRODUCT MUST BE INSTALLED IN ACCORDANCE WITH THE APPLICABLE
INSTALLATION CODE BY A PERSON FAMILIAR WITH THE CONSTRUCTION AND OPERATION
OF THE PRODUCT AND THE HAZARDS INVOLVED.
WESTGATE MFG., INC | 2462 E 28th Street, Vernon, CA 90058 USA |1-323-826-9490|[email protected]
Installation Steps:
Refer to the following diagram when you install the fixture. Five installation methods, directly fix to the
mounting surface or fix to a post with a knuckle.
1.Directly fix to mounting surface
2. (1)Mounting with a Slip fitter:
(2)Mounting with Slip fitter and Wall-mounted adapter:
3. Mounting with Arm.
4. Wall mounted installation.
The mounting method of the straight arm is added to a wall mounted fixing plate, and the fixing plate is mounted
on the wall, and the fixing plate is fixed by a nut.
WESTGATE MFG., INC | 2462 E 28th Street, Vernon, CA 90058 USA |1-323-826-9490|Customerservice@westgatemfg.com
With sensor
Without sensor or photocell
With photocell
With photocell(0-10VDC)
Function description of CCT&Wattage Tunable:
(1) . If the luminaire is designed to be CCT tunable.Please screw the knob cap to select the corresponding
CCT,as shown in Fig. 1, screw the knob cap after using the CCT selectable function.
(2) . If the luminaire is designed to be wattage tunable.Please unscrew the knob cap before using the watt
selectable function. According to the watt selectable label shown in Fig. 2,please toggle the DIP
switch 1,2,3 to select the corresponding watt. Screw the knob cap after using the watt selectable function.
CCT tunable Selector
(3000/ 4000/ 5000/ 5700K)
Fig. 1
Wattage Adjustable
Fig. 2
After installation, please
check whether the lighting fixture is firmly fixed.
check whether wires are connected correctly.
At last, turn on the power, and check if the lighting fixture works well. If not, please turn off the
power and contact with local dealer.
WESTGATE MFG., INC | 2462 E 28th Street, Vernon, CA 90058 USA |1-323-826-9490|Customerservice@westgatemfg.com
Table of contents
Other Westgate Floodlight manuals
