Westgate LFXPRO-LG-50-150W-MCTP Service manual
INSTALLATION INSTRUCTION MANUAL
LED FLOOD LIGHT, 100-277
MODELS:
LFXPRO-LG-50-150W-MCTP, LFXPRO-LG-50-150W-MCTP-WH
LFXPRO-XL-150-300W-MCTP, LFXPRO-XL-150-300W-MCTP-WH
Model number parameter list:
1. Introduction
This LED Flood light uses the latest in solid
state
lighting technology for long life, low maintenance, and high
efficiency.
The same as traditional HID lighting. 150W ~300W there are five different mounting options, suitable for various
occasion.
Use
100-
2
77V
, 50/60Hz AC supply
.
Suitable for using in the following
locations:
•
Ambient Temp: -40~+104°F
•
Wet
Locations
Note: Save these instructions for future
reference.
Item
Model
Input
Voltage
Watt
Input Current
Maximum Weight
1
LFXPRO-LG-50-150W-MCTP
LFXPRO-LG-50-150W-MCTP-WH
100-277V
AC
50W
80W
100W
150W
1.8A
8.6 lbs
2
LFXPRO-XL-150-300W-MCTP
LFXPRO-XL-150-300W-MCTP-WH
120-277V
AC
150W
200W
240W
300W
3.5A
14.3 lbs
2. Installation
For supply connections use wire rated for at least 194°F
Installation Steps:
Refer to the following diagram when you install the fixture. Five installation methods, directly fix to the mounting
surface or fix to a post with a knuckle.
1.Directly fix to mounting surface
Warning:
To avoid the risk of fire, explosion, or electric shock, this product should be installed, inspected, and
maintained by a qualified electrician only, in accordance with all applicable electrical codes.
All the products can not be installed on woods.
Warning:
To avoid electric shock:
•Make sure electrical power is OFF before and during installation and maintenance.
•Luminaire must be connected to a wiring system with an equipment-grounding conductor.
Warning:
To avoid explosion:
•Make sure the supply voltage is the same as the rated luminaire voltage.
•Do not install where the marked operating temperatures exceed the ignition temperature of the
hazardous atmosphere.
•Do not operate in ambient temperatures above those indicated on the luminaire nameplate.
•Keep lens tightly closed when in operation.
2.
(1)Mounting with a Slip fitter:
WESTGATE MFG., INC | 2462 E 28th Street, Vernon, CA 90058 USA |1-323-826-9490|[email protected]
(2) Mounting with Slip fitter and Wall-mounted adapter:
WESTGATE MFG., INC | 2462 E 28th Street, Vernon, CA 90058 USA |1-323-826-9490|Customerservice@westgatemfg.com
3. Mounting with Arm.
4. Wall mounted installation.
The mounting method of the straight arm is added to a wall mounted fixing plate, and the fixing plate is mounted
on the wall, and the fixing plate is fixed by a nut.
Without sensor or photocell
With sensor
With photocell
With photocell(0-10VDC)
Wiring diagram for plug-in sensor
Positions for Sensor and Photocell installed:
Reserved 1/2"-14T thread hole for sensor Reserved the hole for Photocell
3. Function description of CCT&Wattage Tunable:
(1). If the luminaire is designed to be CCT tunable.Please screw the knob cap to select the corresponding CCT,as
shown in Fig. 1, screw the knob cap after using the CCT selectable function.
(2). If the luminaire is designed to be wattage tunable.Please unscrew the knob cap before using the watt selectable
function. According to the watt selectable label shown in Fig. 2,please toggle the DIP switch 1,2,3 to select the
corresponding watt. Screw the knob cap after using the watt selectable function.
After installation, please
check whether the lighting fixture is firmly fixed.
check whether wires are connected correctly.
At last, turn on the power, and check if the lighting fixture works well. If not, please turn off the power and
contact with local dealer.
Wattage Adjustable
Fig. 2
OR
CCT tunable Selector
(3000/ 4000/ 5000/ 5700K)
Fig. 1
This manual suits for next models
3
Table of contents
Other Westgate Floodlight manuals
