Westinghouse LTV-19W3 - 19" LCD TV User manual

Table of Contents
IMPORTANT PRODUCT SAFETY INSTRUCTIONS ........................................................................................... 2
Antenna Installation Safety .......................................................................................................................................... 4
Cleanin2 the LCD TV .................................................................................................................................................. 4
Sat)tv Guidelines ......................................................................................................................................................... 5
FCC Compliance Statement ........................................................................................................................................ 5
INSTALLATION ............................................................................................................................................................ 6
1. Insert Remote Control Batteries ......................................................................................................................... 6
2. Attach Base Stand to LCD TV ........................................................................................................................... 7
3_ Connect Antenna_ Ca ble_ Video_ S-Video_ YPbPr_ DVL and/or VGA Cables ................................................. 8
4 Connect Power Cable ............................................................................................................................................. 9
5 Turn Power On ....................................................................................................................................................... 9
6 Projz_ TV Channels ................................................................................................................................. 10
CONTROLS & CONNECTIONS .............................................................................................................................. 11
Front View of the Product ......................................................................................................................................... 11
Reruote Control .......................................................................................................................................................... 12
The Reruote Control should be used within 3 rueters of the LCD TV ..................................................................... 12
OSD FUNCTIONS ....................................................................................................................................................... 13
TV OSD Menu ........................................................................................................................................................... 13
Image Menu ........................................................................................................................................................... 13
Audio Menu ........................................................................................................................................................... 14
Color Menu ............................................................................................................................................................ 14
TV Menu ................................................................................................................................................................ 15
Miscellaneous Menu .............................................................................................................................................. 15
V-Chip and Parental Control Menu ...................................................................................................................... 16
Rating Menus ......................................................................................................................................................... 17
Video OSD Menu ....................................................................................................................................................... 17
PC OSD Menu ............................................................................................................................................................ 18
Image Menu ........................................................................................................................................................... 18
Audio Menu ........................................................................................................................................................... 19
Color Temp Menu ................................................................................................................................................. 19
Miscellaneous Menu .............................................................................................................................................. 20
1NFO Menu ............................................................................................................................................................ 20
PC DVI OSD Menu ................................................................................................................................................... 21
PIP fi.mction Menu ..................................................................................................................................................... 21
Auto Ad_ ........................................................................................................................................................ 21
Input Source not t_)und or Out of Ran_ ................................................................................................................... 21
APPENDIX .................................................................................................................................................................... 22
_ecifications ............................................................................................................................................................. 22
Troubleshooting ......................................................................................................................................................... 23
No I0ower ................................................................................................................................................................ 23
Power is ON but no screen image ......................................................................................................................... 23
Wrong or abnormal colors ..................................................................................................................................... 23
Snow appears on screen ........................................................................................................................................ 24
No sound ................................................................................................................................................................ 24
Remote control does not work .............................................................................................................................. 24
Remote control code not found in "universal" remote ......................................................................................... 24
How do I find more help'? ..................................................................................................................................... 24

IMPORTANT PRODUCT SAFETY
INSTRUCTIONS
Read carefully and follow all warnings and instructions in this User's Manual and those
marked on the product before you operate your television. Failure to follow warnings can
result in personal injury or damage to product. Keep this User's Manual in a convenient
location for future reference.
Proper Positioning of Television
Always handle your LCD television with care. Avoid touching the LCD screen. Skin oils are
difficult to remove.
Always position your LCD television on a stable and level surface. Unstable surfaces can
cause your LCD to topple and fall, resulting in possible damage or injury.
Avoid exposing the LCD display to direct sunlight or high temperatures, which can damage or
shorten its useful life. Do not place near heat sources such as radiators, heat registers, or
other appliances that generate heat.
Avoid exposing the LCD display to rain, water, moisture or high humidity. Do not place your
LCD near basins or sinks where it may come in contact with water.
Orient your LCD display away from direct sunlight to reduce glare.
Never place heavy or sharp objects on the LCD display, video cable, or power cord.
Overloading Outlets
Do not overload electrical power sources when installing television. Overloading wall outlets,
circuits, or extension cords can result in overheating, fire, or electric shock. Use only
grounded or polarized outlets.
Power Cord Protection
Minimize wear on power supply cords. Power supply cords should be routed away from foot
traffic and contact with other objects. Do not route power cord under rugs or carpeting. The
cord should never be severely bent, pinched, or twisted. Periodically inspect power cords for
wear or damage, particularly near plug and the point where it exits from the product. Unplug
cord and discontinue use if damage is discovered.
Ventilation
Slots and openings on the cabinet are provided for ventilation purposes. To ensure reliable
operation of the product and to protect it from overheating, these openings must not be
blocked or covered. Keep the LCD TV a minimum of four (4) inches away from any wall to
assure sufficient airflow and ventilation. Increased temperatures may cause fire or device
failure.

To assure properventilation, do not block the openings byplacing the LCD TVon a bed,sofa,
rug or other similar surface. Do not place it in a built-in installation, such as a bookcase or an
enclosed rack, unless properventilation is provided.
Other Notices and Precautions
Caution: Never remove the rear cover. There are no user serviceable parts inside. Your LCD
TV contains high-voltage parts. You may be seriously injured if you touch them.
Do not attempt repairs yourself. Your warranty does not cover repairs or attempted repairs by
anyone not authorized by Westinghouse Digital. Refer all servicing and repairs to qualified
service personnel.
If smoke, abnormal noise, or strange odor is present, immediately unplug the power cord.
Contact a qualified service technician
If your LCD TV will not be used for extended periods of time, unplug the power cord and
remove the batteries from the remote control.

Antenna Installation Safety
Outdoor Antenna Grounding
If an outside antenna or cable system is connected to the LCD TV, be sure the antenna or cable
system is grounded so as to prevent voltage surges and built-up static charges. Article 810 of the
National Electrical Code, ANS/NFPA 70, provides information with regard to proper grounding of the
mast and supporting structure, grounding of the lead-in wire to an antenna discharge unit, connection
to grounding electrodes, and requirements for the grounding electrode.
Lightning
For added protection for the LCD TV during a lightning storm, or when it is left unattended and unused
for long periods of time, unplug it from the wall outlet and disconnect the antenna or cable system. This
wilt prevent damage to the product due to lightning and power-line surges. Do not disconnect the
antenna or the power cord during a heavy storm - lightning may strike while you are holding the cable
cord, causing serious injury. Turn off your LCD display and wait for the weather to improve.
Power Lines
An outside antenna system should not be located in the vicinity of overhead power lines or other
electric light or power circuits. When installing an outside antenna system, extreme care should be
taken to keep from touching such power lines or circuits as contact with them may be fatal.
Cleaning the LCD TV
• MAKE SURE THE LCD"IV IS TURNED OFF
•NEVER SPRAY OR POUR LIQUID DIRECTLY ONTO THE SCREEN OR CASE
To clean the screen:
1. Wipe the screen with a clean, soft, lint-free cloth. This removes dust and other particles.
2. If it still is not clean, apply a small amount of non-ammonia, non-alcohol based glass cleaner
onto a clean, soft, lint-free cloth, and wipe the screen.
To clean the case:
1. Use a soft, dry cloth.
2. If it still is not clean, apply a small amount of non-ammonia, non-alcohol based, mild non-
abrasive detergent onto a clean, soft, lint-free cloth, then wipe the surface.
Disclaimer
Westinghouse Digital does not recommend the use of any ammonia or alcohol-based cleaners on the
LCD TV screen or case. Some chemical cleaners have been reported to damage the screen and/or
LCD display case. Westinghouse Digital wilt not be liable for damage resulting from use of any
ammonia or alcohol-based cleaners.

Safety Guidelines
Warning: This device must be operated with the original power supply, part number: UP065]] ]9o
CAUTION: The socket-outlet should be installed near the equipment and should be easily accessible.
CAUTION: Use a power cable that is properly grounded. Always use the appropriate AC cord that is certified for
the individual country. Some examples are listed below:
USA.................. UL Switzerland ...... SEV
Canada ............. CSA Britain .............. BASE/BS
Germany .......... VDE Japan ............... Electric Appliance Control Act
IMPORTANT NOTICE CONCERNING POWER CORD SELECTION
The power cord set for this unit has been enclosed and has been selected according to the country of destination
and must be used to prevent electric shock. Use the following guidelines if it is necessary to replace the original
cord set, or if the cord set is not enclosed.
The female receptacle of the cord set must meet IEC-60320 requirements and may look like (Figure A1 below):
Figure AI_ Figure A2@_
For the United States and Canada
In the United States and Canada the male plug is a NEMA5-15 style (Figure A2), UL Listed, and CSA Labeled.
For units that are mounted on a desk or table, type SVT or SJT cord sets may be used. For units that sit on the
floor, only SJT type cord sets may be used. The cord set must be selected according to the current rating for your
unit. Please consult the table below for the selection criteria for power cords used in the United States and
Canada.
Cord Type Size of Conductors in Cord Maximum Current Rating of Unit
SJT 18 AWG 10 Amps
16 AWG 12 Amps
14 AWG 12 Amps
SVT 18 AWG 10 Amps
17 AWG 12 Amps
FCC Compliance Statement
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
uses, and can radiate radio frequency energy, and may cause harmful interference to radio
communications if not installed and used in accordance with the instructions. However, there
is no guarantee that interference will not occur in a particular installation. If this equipment
does cause harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the interference by
one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
FCC Warninq
To assure continued FCC compliance, the user must use a grounded power supply cord and the provided
shielded video interface cable with bonded ferrite cores. If a BNC cable is going to be used, use only a shielded
BNC (5) cable. Also, any unauthorized changes or modifications not expressly approved by Westinghouse Digital
will void the user's authority to operate this device.

Installation
Congratulations on your purchase of a Westinghouse 19" wide screen LCD TV. Sleek and
practical, this lightweight LCD TV delivers a crisp, vibrant picture and doubles as a superb
WSXGA+ computer monitor --making it a practical solution for tight spaces in the office,
bedroom, or kitchen. Watch television, play video games, e-mail, or surf the Internet.
Package Contents
Your LCD TV package includes:
• 19" widescreen LCD TV
• Attachable Base Stand
• Remote Control (2 AAA batteries are included)
• Cables
o DC Power Adapter Supply
o AC Power Adapter Cord
o VGA (HD15) Male- Male Cable
o 3.5 mm Male - Male Stereo Audio Cable
• Literature
o Quick Connect Guide
o User's Manual
o Warranty Card
Important
Save the original box and all packing material for future shipping needs.
1. Insert Remote Control Batteries
• Remove the battery cover.
• Insert the batteries, paying careful attention to match the corresponding (+) and (_)
markings on the battery compartment.
• Re-attach the battery cover.
CAUTION
• Only use the specified AAA batteries.
• Do not mix new and old batteries. This may result in
cracking or leakage, which may pose a fire risk or lead
to personal injury.
• Insert batteries according to (+) and (_) markings.
Inserting the batteries incorrectly may result in
cracking or leakage, which may pose a fire risk or lead
to personal injury.
• Dispose of the battery in accordance with local laws
and regulations.
• Keep the battery away from children and pets.
• When the remote control will not be used for an
extendec period, remove the batteries.

2. Attach Base Stand to LCD TV
Attach the base stand to the LCD TV stand neck. Align the holes and tabs, press and snap
into place.

3. Connect Antenna, Cable, Video, S-Video, YPbPr, DVI, and/or
VGA Cables
Connect video and audio cables from compatible devices to the back panel of the LCD TV.
Line Ou!
\RF Audio R/L YPbPr
DVI VGA (D-SUB)

4. Connect Power Cable
Connect the DC power adapter cord to the LCD TV and then connect the female AC power
cord to the adapter. Plug the AC power cord into a properly grounded AC outlet.
5. Turn Power On
Press the power button on the right side of the LCD TV or on the remote control. The LED
light will turn blue if signal input is detected, orange if no signal is detected.
__ Power Button
i
Power Button

6. Programming TV Channels
1. Select TV as the input using the Source button on
the remote.
2. Press the Menu button to display the OSD Display
Menu.
3. Use the CH /arrow keys to highlight the TV Menu.
,Using the Vol _ arrow keys select the TV sub-menu.
Use the _to highlight the CH Auto Scan function.
Press Vol _ arrow key and Channel Auto Scan will
be performed.
5. Once the CH Auto Scan is complete, switch
channels by using the CH /arrow keys on the
remote.
,To Add/Erase channels use the _ to highlight the
CH Edit function. Use the _, or _ to add or erase the
selected channel
1A

Controls & Connections
This section describes the side panel controls, and remote control in more detail.
Front View of the Product
Use the buttons on the right side panel control to display and adjust the On Screen Display
(OSD). The OSD controls are explained at the bottom of the page and are defined in the "OSD
Functions" section.
IR Receiver Speaker Control keys are shown
in detail to right
1
2
3
4
5
6
II
Button Mode " TV Source " OSD Menu
OH,A
i
2 OH-- Y
3 . Vo]- 4
4 , vo!+ I_
5 MenulSource
Pow_
Channel up Navigate up
Channel down Navigate down
Volume down Decrease value
Volume up Increase value
Press and hold for 2sec. to
access menu. Press and release Enter/Exit Menu
to change source
TV ON or OFF TV ON or OFF
11

Remote Control
The Remote Control should be used within 3 meters of the LCD TV.
1. Mute
Switch the sound between on & off
2. MTS(Multi-channel TV Sound)
Stereo and Mono selection
3. Sleep
Use to shut off TV after a period of time
4. Power
Switch the power between on & off
5. Display
Display the channel information
6. PIP
Available in D-Sub/DVl/YPbPr Modes, used
to turn PIP picture on & off and select PIP
picture size
7. PIP Menu
Used to navigate through the PIP OSD
menu and control audio swap
8. Return
Recall the previous channel
9. CHANNEL NUMBER KEY 0-9, 100
Direct channel selection by number
10.V-Chip
Set Parental and Movie Rating
Block/UnBIock features. Navigation
through OSD menus. Pin Code is also set
here.
11.CH /
Channel Up/Down adjustment; also
available on key controls and OSD menu
12.Source
Push to select input source.
13. MENU
Press to enter OSD Menus
14.Vol /
Volume Up/Down adjustment; also
available on key controls and OSD menu
control. If OSD menu is displayed, Step
Down into OSD Menus
15.CC
Set Closed Caption and Text modes toggle
through OFF, CCl, CC2, CC3 etc.
16.Scaling
Push to select picture aspect
ratio.(NormaltZoom/Full)
17.Exit
Exits OSD menu.
1__
2
5
8
10
11
3
4
12
13
17
19

OSD Functions
This section describes each on-screen display (OSD) command. There are different OSD
menus depending on whether you are in TV, Video (AV/S-Video/YPbPr) or PC (D-Sub/DVI)
mode.
All the function settings for your LCD TV are controlled either via the remote control or using
the control keys located on the right of the front panel of the LCD TV. To display the OSD
main menu, press and hold the Menu button on the control keys or the MENU key on the
remote control. Use the /arrow keys to navigate within the menu. The /arrow keys are
used to change the values of the functions that are selected in the OSD menu. The EXIT key
on the remote control or Menu button on the control keys allows you to exit out of the OSD
menus and functions.
TV OSD Menu
Enter OSD Menus by
pressing MENU key
Image Menu
In the Image Menu use the Vol_ to select image sub-menu. Use
CH /to highlight function then use the Vol /arrow keys to
change the values of the functions that are selected in the OSD
menu.
Brightness
Contrast
Sharpness
Color
Hue
DLC
Back Light
Brightness adjustment
Contrast adjustment
Video Sharpness adjustment
Color Levels adjustment
Video Hue adjustment
Turn Dynamic Luminance Control On or Off
Backlight from 0-100 adjustment

Audio Menu
In the Audio Menu use the Vol_ to select Audio sub-menu. Use CH /to highlight function
then use the Vol /arrow keys to change the values of the functions that are selected in the
OSD menu.
Volume Volume adjustment
Mute Turn Audio Off and On
Treble Treble adjustment
Bass Bass adjustment
Balance Left to Right Audio adjustment
MTS Multi-channel Television Sound, select SAP, MONO, or STEREO
Color Menu
In the Color Menu use the Vol_ to select Color sub-menu. Use CH /to highlight function then
use the Vol /arrow keys to change the values of the functions that are selected in the OSD
menu.
Red
Green
Blue
Red level adjustment
Green level adjustment
Blue level adjustment

TV Menu
In the TV Menu use the Vol_ to select TV sub-menu. Use CH /to highlight function then use
the Vol /arrow keys to change the values of the functions that are selected in the OSD
menu.
Tuner System
CH. Auto Scan
CH. Fine Tune
Blue Screen
CH. No
CH. Edit
C.C.
C.C. Background
Select between STD, HRC, IRC, Air
Start to scan channel after pressing right or left key, and stop scan if any key is
)ressed,
Tune channel from 0-100
Toggle between video blanking to blue between channel changes - default is No
Current channel
Select the channel to Edit using _/_ arrow keys
Closed Caption Display
Turn C,C, background off or on
Miscellaneous Menu
In the Misc Menu use the Vol_ to select Misc sub-menu. Use CH /to highlight function then
use the Vol /arrow keys to change the values of the functions that are selected in the OSD
menu.

Language English, Chinese, Fran£ois, EspaSol
OSD Transparency Set OSD transparency level
OSD Time-out Set the time to turn off the OSD automatically
OSD Position OSD horizontal/vertical positionadjustment
Reset Restore factory default settings
Sleep Set the Sleep timer for 30, 45, 60, 90, or 120 minutes
Power LED Turn the LED light OFF or ON
Aspect Ratio Set the display to Full, Normal, or Zoom
V-Chip and Parental Control Menu
To access the PARENTAL CONTROL menu press the V-Chip button located on the remote
control. Enter the Pin Code (default is 0000).
To change the Pin Code, enter new Password and confirm new Password is set.

Rating Menus
Press the V-Chip button on the remote control to access the Parental Control Menu. Enter the
PIN code. Use the _ to highlight the Movie (MPAA) or TV (TVPG) menu. Use the _ to select
the sub-menu. Use the /to highlight the Movie/TV Rating to be blocked or un-blocked.
Press the MENU button to set and press EXIT to exit the V-chip menu.
Function Name I Explanation
MOVIE RATING G:
PG:
PG 13:
R:
NC 17:
X:
TV RATING Y:
Y7:
G:
PG:
14:
MA:
General audience
Parental Guidance suggested
Parents strongly cautioned
Restricted
No one 17 and under admitted
Adult audience only
<<< AGE >>>
All Children
Directed to Older Children
General Audience
Parental Guidance Suggested
Parents Strongly Cautioned
Mature Audience Only
Video OSD Menu
Video (AV/S-Video/YPbPr) OSD Menu has the same OSD features as the TV OSD except for
the TV sub-menu functions.
1'7

PC OSD Menu
Image Menu
In the Image Menu use the Vol_ to select image sub-menu. Use CH /to highlight function
then use the Vol /arrow keys to change the values of the functions that are selected in the
OSD menu..
Brightness
Contrast
Sharpness
Clock
Phase
H-POSITION
V-POSITION
Auto-Config
Brightness adjustment. Default value is 100.
Contrast adjustment. Default value is 50.
Adjust picture sharpness from 1 - 5. Default value is 2.
Adjust the Clock timing. Default value is 50.
Adjust the Video Hue level. Default value is 55.
Adjust OSD on horizontal position. Default value is 50.
Adjust OSD on vertical position. Default value is 50.
Adjustautomatically the picture and synch the LCD TV monitor

Audio Menu
In the Audio Menu use the Vol_ to select Audio sub-menu. Use CH /to highlight function
then use the Vol /arrow keys to change the values of the functions that are selected in the
OSD menu.
Volume
Mute
Treble
Bass
Balance
MTS
Volume adjustment
Turn Audio Off and On
Treble adjustment
Bass adiustment
Left to Right Audio adjustment
Multi-channel Television Sound, select SAP, MONO, or STEREO
Color Temp Menu
In the Color Temp Menu use the Vol_ to select Color Temp sub-menu. Use CH /to highlight
function then use the Vol /arrow keys to change the values of the functions that are selected
in the OSD menu
I
Function Name Explanation
Red Red Temp adjustment
Green Green Temp adjustment
Blue Blue Temp adjustment
10