Westinghouse Q01BM1740-08 User manual

Instruction Manual
Model: Q01BM1740-08
SOLAR PROJECTION SPOTLIGHT SET
BLUETOOTH CONTROLLED
®
09/2017
E 1/7
User Manual
Product Name: LED Spot Light
Model:Q01BM1740-08
Manufacture: Quanxin Lighting & Electrical (USA) Inc

09/2017
E 2/7
Crystalline Panel
Protective Film
INSTALLATION
1. Prior to installation download the app to ensure phone compatibility. Download the
Westinghouse Smart Landscape App for free from the App Store or Google Play. You
may also scan the QR codes below. This App is compatible with iPhone (4 generation
or above) and Android™ devices (5.0 or above).
2. Ensure that Bluetooth is enabled on your cellular device and make it discoverable.
The way you do this depends on the device. If you need help visit the manufacturer's
website to learn how.
3. Spotlights include a "Parent" and "Child" light. The light with
the large sticker on top is the "Parent”. This light also has a
reset button located under the solar panel. Only the "parent"
light will operate independently. With the solar panels facing

darkness. The “Parent” light power switch must be turned
!
take 15 to 30 seconds for both lights to illuminate equally.
#$%%
stickers.
RESET BUTTON
Parent Light
Child Light
5. Attach (Part A) to (Part C) by aligning the holes, then insert
(Parts B & D) and tighten (Part B) until secure. To adjust the light
head, loosen (Part B) and position the light head. When desired
position is achieved, tighten (Part B) until secure. To adjust the
solar panel loosen the wing nut and position the panel. When
desired position is achieved, tighten wing nut until secure. Carefully
insert (Part C) into the ground where desired. Push the stake into
the ground until the top collar is even with the ground surface.
NOTE: If the ground is hard and packed, moisten the ground with
water before inserting the stake to avoid breakage.
ASSEMBLY(SOME PARTS MAY COME PRE-ASSEMBLED)
6. Install solar light where it will receive direct sunlight for at least 8
hours each day. Avoid shadowed locations and install away from
nighttime light sources which will prohibit the light from working properly.

09/2017
S 5/7
09/2017
E 3/7
The operational range between your Bluetooth device and
the lights is 32ft-82ft(10m-25m). The distance depends on
the Bluetooth device and environment. Open the App and
select View Tutorial for instructions or select Control My
Lights to begin using your lights. The timer function is not
%*
Bluetooth control is inactive after 4 hours of use. It will
+!*!
recharged. To over-ride this measure you can turn off
and on your lights and follow the instructions in step 3.
This will reduce the runtime until the sun recharges the
batteries in your lights.
APP TUTORIAL
OPERATION
32ft-82ft (10m-25m)
7. FOR FIRST TIME USE: Solar light needs to charge in full sunlight for 8-12 hours with
;**
capacity.

09/2017
S 4/5
09/2017
E 4/7
4
RESET BUTTON
If you are unable to reset your user name and password
using the App on your cell phone, set the “parent” light switch
to “ON” position and press the reset button on the “parent” light
for at least 3 seconds until the light color turns red. The app
will prompt you to assign a new password. Enter "1234".
Tap the lock icon on the app screen. Select desired password
option and reset the password using your own number
sequence. Note that any previously saved functions will need
to be reset.
RESET BUTTON INSTRUCTIONS

09/2017
S 3/5
09/2017
E 5/7
If the light doesn’t turn on, remove battery, wipe both ends with a clean, dry cloth and
reinstall battery. Check the battery to ensure that it is making secure contact with the
terminals. If this doesn’t work, replace with a new battery.
TROUBLE SHOOTING
APP HELP
Connection Failed
The device may not be connectible due
to the following reasons:
1. The request to enter pairing code is
not responded to within 30 seconds.
2. The entered pairing code is incorrect.
3. Bluetooth is turned off or unavailable
on the device.
4. The pairing is cancelled.
Make sure the device is turned on and in
range and that Bluetooth is turned on and
is discoverable, and then pair. If it still
is unable to connect, please restart
Bluetooth and try to pair again.
Back
Email Customer Service
Call Customer Service
8:00am - 5:00pm CST
Unable To Locate Device
1. Your device may be turned off.
2. The device’s battery level may be
low or drained, or the device
is out of range.
3. Bluetooth is turned off or
undiscoverable on the device.
Make sure the device is turned on and
in range, and Bluetooth is turned on
and discoverable, and then add a
Bluetooth device to connect. The
device must be discoverable before
pairing and in range.
Back
Email Customer Service
Call Customer Service
8:00am - 5:00pm CST
How To Connect A Device
Make sure both the device and your
Bluetooth are turned on and
discoverable. Then, add a Bluetooth
device to connect.
Back
Email Customer Service
Call Customer Service
8:00am - 5:00pm CST

09/2017
S 3/5
09/2017
E 6/7
Battery
Top Section
Slide the power switch to the "OFF" position.
Remove the four screws from the top section
using a Phillips head screwdriver. Remove the
old battery and replace with a new 3.7V, 2000
mAh lithium (18650) rechargeable battery.
Replace the top section with the four screws.
Slide the power switch to the "ON" position.
For optimum performance, allow solar light
to charge in direct sunlight.
REPLACING THE BATTERY
Screws
ON/OFF Switch
Reset Button
Scheduled Power On/Off
The device references the time on
your phone. If the time on your phone is
wrong, the schedule will also be wrong.
Make sure the time is correct on your phone.
If the issue persists, please contact
support below.
Back
Email Customer Service
Call Customer Service
8:00am - 5:00pm CST
Forgot Password
You may reset the password to 1234 by
pressing and holding the button on
the device as instructed in the user guide.
Online password recovery is
not currently supported.
Back
Email Customer Service
Call Customer Service
8:00am - 5:00pm CST
Connecting 10 Lights
Q: Why can’t I simultaneously connect
all 10 lights I purchased?
A: Due to the limitation of the mobile
phone functionality, currently only
approximately up to 8 simultaneous Bluetooth
connections are supported, limiting the
number of connected devices.
Back
Email Customer Service
Call Customer Service
8:00am - 5:00pm CST

09/2017
S 3/5
09/2017
E 7/7
www.westinghousesolarlights.com
For assistance with assembly or instruction, parts and customer service, call:
U.S.A. & Canada only: 1-844-551-0680
8am – 5pm Monday – Friday, Central Standard Time Or email: [email protected]
<=$>?@**!
*!@*@
*JKX
@*@Z[*\]^
or rechargeable (Nickel Cadmium or Nickel Metal Hydride) batteries .
, WESTINGHOUSE, are trademarks of Westinghouse Electric Corporation. Used
under license by Sky Rich Star Limited. All Rights Reserved.
The Bluetooth word mark and logos are registered trademarks owned by Bluetooth
SIG, Inc. and use of such marks by Sky Rich Star Limited is under license. Other
trademarks and trade names are those of their respective owners.
The Westinghouse Smart Landscape App may require periodic updates without prior
notice. Check your mobile app store for the most updated version.
®
iPhone is a registered trademark of Apple Inc. registered in the U.S. and other countries.
Android is a trademark of Google Inc. Google Play and the Google Play logo are
trademarks of Google Inc.

FCC Warning
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
Any Changes or modifications not expressly approved by the party responsible for compliance could void
the user's authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment generates uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
-Consult the dealer or an experienced radio/TV technician for help.
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled
environment.