Westone 07-3101-W-A User manual

REV 032309
MANUAL MEAT
CUBER/TENDERIZER
INSTRUCTIONS
MODEL # 07-3101-W-A
ATTENTION
If any components of this unit are broken,
do not operate properly, or for product returns,
please contact Pragotrade LLC at
1-800-814-4895
Outside the U.S. call 440-638-3131.
For the online catalog, log onto www.westonsupply.com.
Exclusively imported by Pragotrade LLC Strongsville, Ohio
www.pragotrade.com
LLC
u.s.a.

-2-
MANUAL MEAT
CUBER/TENDERIZER
MODEL # 07-3101-W-A
COMPONENT LIST
DIAGRAM NO. PART DESCRIPTION PART NO.
1 Lower Housing 07-3184-A
2 Top Housing 07-3181-A
3 Handle 07-3125-A
4 Stainless Steel Blade Rack Assembly 07-3103
5 Stainless Steel Left Comb 07-3119
6 Stainless Steel Right Comb 07-3118
7 Housing Thumbscrew (2) 07-3166
8 Handle Thumbscrew 07-3145
9 C-Clamp (2) 07-3105
10 Base 07-3111
11 Left Leg 07-3179-L-A
12 Right Leg 07-3179-R-A
13 Chute 07-3182-A
14 Nylon Bushing 07-3127
15 Stainless Steel Tongs 07-3151
16 Screw for Chute and Base (6) 07-3183
17 Screw for Legs (4) 07-3180
18 Allen Wrench for Chute & Base Screws 07-3178
19 Allen Wrench for Leg Screws 07-3185
20 Shaft Clip (2) 07-3165
WARRANTY INFORMATION
SAVE THIS WARRANTY INFORMATION FOR YOUR RECORDS!
Pragotrade LLC warrants to the ORIGINAL RETAIL PURCHASER of this product that if operated in accordance
with the printed instruction accompanying it, then for a period of 1 year from the date of purchase, the product shall be
free from defects in material and workmanship.
The Warranty Card, along with a copy of the original receipt, must be received by Pragotrade LLC within 30 days
from purchase date for the warranty to apply. Failure to send the completely lled out Warranty Card, along with a copy
of the original receipt, will void the warranty.
The product must be delivered to or shipped freight prepaid to Pragotrade LLC for warranty services, in either its
original packaging or similar packaging affording an equal degree of protection. Damage due to shipping is not the
responsibility of the company. Pragotrade LLC charges a $35.00 per hour bench charge. NOTE: No repairs will be
started without the authorization of the customer. The return shipping cost to the customer will be added to the repair
invoice.
Pragotrade LLC will repair (or at its discretion, replace) the product free of charge, if in the judgment of the company,
it has been proven to be defective as to seller’s labor and material, within the warranty period.
New or rebuilt replacements for factory defective parts will be supplied for one (1) year from the date of purchase.
Replacement parts are warranted for the remainder of the original warranty period.
For non-warranty repairs, contact Pragotrade’s Customer Service at 1-800-814-4895 M-F 8am-5pm EST (outside of
the United States 440-638-3131) to obtain a Return Authorization Number (RMA Number). Pragotrade will refuse all
returns that do not contain this number. DO NOT RETURN THE UNIT WITHOUT PROPER AUTHORIZATION
FROM PRAGOTRADE LLC.
LIMITATIONS: The warranty is void if the product is used for any purpose other than that for which it is designed.
The product must not have been previously altered, repaired, or serviced by anyone else other than Pragotrade LLC.
If applicable, the serial number must not have been altered or removed. The product must not have been subjected
to accident in transit or while in the customer’s possession, misused, abused, or operated contrary to the instructions
contained in the instruction manual. This includes failure caused by neglect of reasonable and necessary maintenance,
improper line voltage and acts of nature. This warranty is not transferable and applies only to U.S. and Canadian
sales.
Except to the extent prohibited by applicable law, no other warranties whether expressed or implied, including
warranty merchantability and tness for a particular purpose, shall apply to this product. Under no circumstances shall
Pragotrade LLC be liable for consequential damages sustained in connection with said product and Pragotrade LLC
neither assumes nor authorizes any representative or other person to assume for it any obligation or liability other than
such as is expressly set forth herein. Any applicable implied warranties are also limited to the one (1) year period of
the limited warranty.
This warranty covers only the product and its specic parts, not the food or other products processed in it.
CUT ALONG THE DOTTED LINE AND SEND THE WARRANTY CARD ALONG WITH A
COPY OF YOUR ORIGINAL PURCHASE RECEIPT TO:
Pragotrade LLC
20365 Progress Drive, Strongsville, OH 44149
WARRANTY CARD
SEND THIS CARD ALONG WITH A COPY OF YOUR ORIGINAL PURCHASE RECEIPT
Customer Name: ________________________________
Address: ______________________________________
City/State/Zip: ___________________________________
Telephone Number: (_________) ___________________
E-Mail Address:___________________________________
OriginalDateof Purchase:_______/_________/__________
Product Model #: __________________________________
Serial # (if applicable): ____________________________
If any components of this unit are broken or the unit does not operate
properly, call Pragotrade LLC Toll Free at
1-800-814-4895
Monday thru Friday 8:00am-5:00pm EST.
Outside the U.S. call 440-638-3131

-3--6-
1
2
3
4
5
6
7
8
9
10
12
11
13
17
16
15
18
19
14 16
20
DIRECTIONS FOR USE 17
DISASSEMBLY & CLEANING INSTRUCTIONS
1. Keep children at a safe distance from machine while cleaning.
2. Remove the Handle Thumbscrew from the Handle. Remove
Handle from the Blade Rack Shaft by unscrewing the Handle
Thumbscrew.
3. Remove the Combs from the Top Housing by lifting up on
Combs.
4. Remove the two Thumbscrews from the Top Housing.
5. Remove the Top Housing. WARNING! This will expose the Cutting Blades.
Take care when handling the Blade Assembly.
6. Using the provided Allen Wrench, remove the Chute from the Top Housing.
7. Carefully lift the Blade Rack Assembly from the Lower Housing.
8. Disassemble the Lower Housing from the Legs. Disassamble the Legs from
the Base.
8. Wash all parts thoroughly with warm, soapy water. Rinse with clear water. A
long bristle brush is recommended for cleaning the Blade Rack Assembly. Take
extra care when handling the Blade Racks.
9. Dry thoroughly before re-assembling.
NOTE: It is highly suggested to coat all metal parts with a food-grade silicone spray
(sold separately) to prevent corrosion.
Remove all bones or hard items in the meat before tenderizing or cubing. Damage
to the unit may occur if bones or hard objects are pushed through.
Do not cube or tenderize meat that is more than 1” (2.5 cm) thick. Thicker meat
may get lodged in Blades, which may cause damage to the product.
Insert the meat to be tenderized or cubed into the mouth of the Chute until the
meat comes in contact with the Blades. Turn the Handle in a clockwise motion.
This will pull the meat through the Blades. Insert only one piece of meat at a time to
prevent jamming.
If a piece of meat is too short to reach the Blades, use the provided Tongs to
guide the meat to the Blades.
CAUTION! DO NOT press or push the meat into the Chute with your fingers or
any other object. Doing so may cause personal injury and/or damage to the unit. DO
NOT push the Tongs or other utensils into the Blades.
It may be necessary to pass the meat through the Cuber/Tenderizer several
times to obtain the desired results. You may also pass the meat through at different
angles if a different result is desired.
Clean the unit before and after each use.
•
•
•
•
•
•
•

-4- -5-
ASSEMBLY INSTRUCTIONS
1. Connect the Left and Right Legs to the
Base using the provided Allen Wrench and
Screws.
2. Using an Allen Wrench and Screws,
attach the Left and Right Legs to the Lower
Housing. Figure 1
3. Install the Chute to the Top Housing
using an Allen Wrench, Screws.
4. Insert the Blade Rack Assembly into
the Lower Housing, guiding the Drive
Shaft into the bearing journals. Make sure
the teeth of the Blade Racks are properly
meshed together.
5. Position the Top Housing onto the Lower
Housing and line up the screw holes.
6. Secure the Top Housing to the Lower
Housing using the Housing Thumbscrews.
DO NOT OVERTIGHTEN!
7. Insert the Left Comb and Right Comb
into the Top Housing. Figure 2
NOTE: The Left Comb is marked with an
“L” on the upper portion of the Comb. The
Top Housing is marked with an “L Comb”
and “R Comb” to aid in Comb installation.
8. Install Handle onto the Blade Rack Shaft.
Secure the Handle to Blade Rack Shaft with
the Handle Thumbscrew .
GENERAL SAFETY RULES
READ AND FULLY UNDERSTAND ALL INSTRUCTIONS
AND WARNINGS PRIOR TO USING THIS PRODUCT.
YOUR SAFETY IS MOST IMPORTANT! FAILURE TO
COMPLY WITH PROCEDURES AND SAFEGUARDS MAY
RESULT IN SERIOUS INJURY OR PROPERTY DAMAGE.
REMEMBER: YOUR PERSONAL SAFETY IS YOUR
RESPONSIBILITY!
WARNING!
SAVE THESE INSTRUCTIONS!
Refer to them often and use them to instruct others.
1. NEVER REACH INTO the Cuber/
Tenderizer. Doing so could cause serious
injury. ALWAYS USE THE PROVIDED
TONGS.
2. KEEP FINGERS CLEAR OF THE BLADES
AT ALL TIMES. Failure to do so may result in
personal injury. The Cutting Blades/Blade
Assembly is very sharp. It is recommended
to wear Kevlar, cut resistant gloves when
handling the Blades.
3. DO NOT press or push meat into the Chute
with your fingers or any other object. Doing
so may cause personal injury and/or damage
to the unit.
4. NEVER use fingers to scrape food away
from the Cuber/Tenderizer while the grinder
is in operation. SEVERE INJURY MAY
RESULT.
5. DO NOT push the Tongs or other utensils
into the Blades.
6. NEVER LEAVE THE Cuber/Tenderizer
UNATTENDED. Close supervision is
necessary when any appliance is used near
children. This appliance is NOT to be used by
children.
7. NEVER use any accessories or parts from
other manufacturers. Doing so will VOID YOUR
WARRANTY.
8. Thoroughly clean all parts that will come
into contact with food before using the
Tenderizer/Cuber. Wash all parts by hand
and dry thoroughly. WARNING! Protective/
cut-resistant Kevlar gloves are recommended
when handling the blade assembly.
9. DO NOT attempt to tenderize meat with
bones or other hard items. Damage to the
machine will occur.
10. TIE BACK loose hair and clothing, and roll
up long sleeves before operating the Cuber/
Tenderizer. REMOVE ties, rings, watches,
bracelets, or other jewelry before operating the
Cuber/Tenderizer.
11. DO NOT use the Cuber/Tenderizer while
under the influence of drugs, medications or
alcohol.
ADDITIONAL ACCESSORIES AVAILABLE
6” Jerky Slicer Blade 07-3302
Food-Grade Silicone Spray 03-0101-W
Kevlar Gloves Small 34-0101
Kevlar Gloves Medium 34-0102
Kevlar Gloves Large 34-0103
Cuber/Tenderizer Motor Attachment 01-0103-W
Pro-2100 Vacuum Sealer 65-0101
Vacuum Sealer Bags Multi Pack 30-0107-W
These products and many more products can be ordered by visiting
www.westonsupply.com or by calling
Pragotrade LLC Toll Free at 1-800-814-4895
Monday thru Friday 8:00am-5:00pm EST.
Outside the U.S. call 440-638-3131
Figure 1
Legs
Lower
Housing
Base
Chute
Top
Housing
Blade Rack
Assembly
Blade Rack
Shaft
Figure 2
Comb