(1)
(2)
(3)
(4)
(5)
(7)
(6)
Button
1
2
3
4
5
6
7
Power ON/ pressing for 3 seconds to switch to white lighting
Power OFF
Select the color (capacitive touch)
Increase/decrease the brightness of the light in single color
mode / Multicolor changing mode / Music control mode
Increase/decrease the speed of the light in multicolor
changing mode
Multicolor changing mode switch
Music mode switch
Function
Mode 1
Mode 2
Mode 3
Mode 4
Mode 5
Mode 6
Static Mode (including seven colors)
Seven Color Blink
RGB Gradual
Seven Colors Gradual
Single Color Blink Function
(Red/Green/Blue/Yellow/Purple/Cyan/White)
Dierent Mixed Color
(Red+Green/Red+Blue/Green+Blue)
Multicolor Changing Mode
Mode 1
Mode 2
Mode 3
Mode 4
Mode 5
Seven single color music mode
(Red/Green/Blue/Purple/Orange/Cyan/White)
Seven single colors blink
Seven single colors Gradual
Red Hopping/Green Hopping/Blue Hopping
Dierent mixed color
(Red+Green/Red+Blue/Green+Blue)
Music Control Mode
MEMORY FUNCTION: The controller will keep the last mode in memory by
power switch ON/OFF.
Wet Sounds RF-RGB-MC V2 Owner’s Manual
The Wet Sounds™RF RGB Music Controller is a multi-function RGB LED Music
Controller. It utilizes the most advanced pulse-width modulation (PWM) remote
control technology. The RF-RGB-MC V2 controls full color LED lighting with four
lines, three circuits (common anode), with more than 640,000 combination
colors. It has 6 multi-light changing modes and 5 music sensitive modes for
your choice in environmental scenes! The 433Mz Wide Range RF wireless
remote control technology features low power consumption, long distance
transmission, and anti-interference circuitry. The sleek and stylish remote has a
simple functionality design for ease of color control, brightness, dimming, and
music scenes. The capacitive touch screen design not only makes the remote
easy to use, but is very cool too!
Safety matters! Please follow all 12V installation guidelines for safe
use on your vehicle.
1. Do not install the product in areas with a strong magnetic eld or high SPL
sound pressure.
2. Make sure your connections are correct and the controller plus each LED run
is individually fused to protect from a short circuit.
3. Please install the controller in an area with good ventilation to ensure
proper heat dissipation.
4. Please ensure that the RF-RGB-MC V2 has a fused 12V power input.
5. Please connect all RGB strips to the unit before connecting to 12V power.
6. Wire the Wet Sounds RF-RGB-MC V2 to a master switch to shut off power
when put into storage or the vehicle is not in use.
7. Please contact Wet Sounds (877-938-7757) for any questions concerning your
Wet Sounds RF-RGB-MC V2.
Maintenance
Inspect the wiring and RF-RGB-MC V2 connectivity before each outing. If you
determine that the wiring or unit is damaged then disconnect until the wiring
or unit is repaired. If you detemine that the RGB strip is damaged then power
down the RF-RGB-MC V2 until the RGB strip is replaced.
RF RGB MUSIC CONTROLLER
Wet Sounds RF-RGB-MC V2 Owner’s Manual
Top view
Sensitivity control
Input for power supply
12VDC (RED 12V Positive,
Black 12V Ground)
2 way-output (for
RGB LED Strips)
Side view
Plug the audio cable into the 1/8” (3.5mm)
stereo plug on controller from your audio
source
The RGB controller has
internal sensors that will
respond to vibration and
sound. For some applications
audio signal from a source
unit will need to be ran to the
3.5mm input jack. The dial on
the device is to ne turn the
music response feature.
Press and hold
music up and down
at the same time
while plugging power
into the RF-RGB-MC V2
control box. Connected
LEDs should ash white three times to
conrm pairing with remote.
Instructions for
pairing remote
to RF-RGB-MC V2
if remote is not
working. Only
one remote can
be paired to the
controller.
Important Operational Instructions
