Wexiodisk WD-T60 User manual

DRYING ZONE
WD-T60, WD-T60F, WD-T80, WDT-90
(translation of the original documentation)
Read the manual before using the machine!
Installation and user manual
S/N: (En) Valid from: 202007 Rev.: 4.0

1. General instructions ........................................................................ 1
1.1 Symbols used .................................................................................................. 2
1.2 Machine rating ................................................................................................. 3
1.3 Checking that the machine and manual correspond ........................................ 3
1.4 EU Declaration of Conformity .......................................................................... 4
2. Safety instructions ........................................................................... 5
2.1 General information ......................................................................................... 5
2.2 Transport .......................................................................................................... 6
2.3 Installation ........................................................................................................ 6
2.4 Operation ......................................................................................................... 6
2.4.1 High temperatures .................................................................................... 6
2.4.2 Risk of crushing ........................................................................................ 6
2.4.3 Risk of slipping .......................................................................................... 6
2.4.4 Sounds ...................................................................................................... 6
2.5 Cleaning the machine ...................................................................................... 6
3. Installation instructions ................................................................... 8
3.1 General information ......................................................................................... 8
3.2 Requirements for the installation site ............................................................... 8
3.3 Transport and storage ...................................................................................... 9
3.4 Unpacking ........................................................................................................ 9
3.5 Installation ...................................................................................................... 10
3.5.1 Preparing for the installation ................................................................... 10
3.5.2 Assembling drying zone WD-T80 ........................................................... 10
3.5.3 Assembling drying zone WD-T60 and WD-T90 ...................................... 11
3.5.4 Assembling drying zone WD-T60F ......................................................... 12
3.6 Connections ................................................................................................... 13
3.6.1 Electrical connection ............................................................................... 13
3.7 Trial operation ................................................................................................ 14
3.7.1 Start-up schedule .................................................................................... 14
3.8 Documentation ............................................................................................... 14
WD-T60, WD-T60F, WD-T80, WD-T90 Rev. 4.0 (202007)

4. Operating instructions ................................................................... 15
4.1 Preparations ................................................................................................... 16
4.2 Using the machine ......................................................................................... 17
4.3 After use – Cleaning ...................................................................................... 17
4.3.1 Incorrect cleaning methods ..................................................................... 17
4.3.2 Cleaning .................................................................................................. 18
4.4 Operating problems ....................................................................................... 18
5. Technical specifications ................................................................ 19
WD-T60, WD-T60F, WD-T80, WD-T90 Rev. 4.0 (202007)

WD-T60, WD-T60F, WD-T80, WD-T90 Rev. 4.0 (202007)
General instructions
1
1. General instructions
Read the instructions in this manual carefully as they contain important informa-
tion regarding the correct, effective and safe installation, use and servicing of the
machine. Service personnel should have access to all documentation for the ma-
chine.
Keep this manual in a safe place so that it can and should be used by other op-
erators of the machine.
• The machine is intended to be used for drying dishware which has been
washed in an associated machine and which is used in the general catering
and restaurant trade. Other uses are NOT recommended!
• The machine can be equipped with a number of different options. Certain
options may be standard in a number of countries. Check what your ma-
chine is equipped with.
• The dishwasher’s display indicates what the machine is doing. The ma-
chine’s various temperatures and any alarms are also shown.
• The capacity requirements of the machine can be found in the TECHNICAL
DATA chapter.
• The electronics in the machine are RoHS compatible.
Before the machine is started up and used, the following points should be ob-
served:
• The SAFETY INSTRUCTIONS chapter must be studied carefully before
commissioning the machine.
• Installation of the machine must be performed in accordance with the re-
quirements and instructions indicated in the INSTALLATION INSTRUC-
TIONS and TECHNICAL SPECIFICATIONS chapters.
• Any personnel who may at some point use the machine must be trained in
its operation, use and care.
• The machine should not be used by anyone suffering from a physical or
mental illness.
• A close eye should be kept on any children in the vicinity of the machine to
ensure they do not tamper with it.
• All cover plates must be installed during use.
The machine and equipment requires an annual service. Contact one of our au-
thorised and trained service companies for such a service.

WD-T60, WD-T60F, WD-T80, WD-T90 Rev. 4.0 (202007)
General instructions
2
1.1 Symbols used
This symbol warns of situations where a safety risk may arise. The instructions
given should be followed in order to prevent injury and dangerous situations.
This symbol on a machine part warns of electrical equipment. The machine must
be entirely non-live during servicing, turn off the power at the power switch and if
required, the switch should be locked to prevent unintentional operation. The
component may only be removed by a qualified electrician.
This symbol warns that the machine’s electronics are sensitive to electrostatic
discharge (ESD), which is why a static electricity wristband must be used when
handling the electronics at all times.
This symbol explains the right way to perform a task in order to prevent poor re-
sults and/or damage to the machine.
This symbol identifies recommendations and hints to help you get the best results
when washing, to increase the machine’s lifespan and reduce the risk of emer-
gency shutdown.
This symbol explains the importance of careful and regular cleaning of the ma-
chine to meet hygiene requirements.
This symbol warns of the importance to read the manual before using the ma-
chine.
This symbol warns that local regulations must be followed for recycling of pack-
aging etc. as well as the destruction of the machine.
This symbol shows where any earth cable for potential equalisation can be con-
nected. The earth bolt is placed on the machine’s stand.

WD-T60, WD-T60F, WD-T80, WD-T90 Rev. 4.0 (202007)
General instructions
3
1.2 Machine rating
Where a dishwasher is supplied with a drying zone, the equipment will have a
common rating plate.
If the drying zone for an existing dishwasher is delivered at a later date, the ma-
chine's rating plate will be updated and will apply to both the machine and the dry-
ing zone.
A free-standing drying zone designed for mounting on a roller table comes sup-
plied with its own rating plate, located on the inside and on the back.
The machine has two rating plates, one of which is placed at the bottom of one
side of the machine and the other in the electrical cabinet. The technical informa-
tion on the plates is also included on the machine's wiring diagram. The various
rating fields show:
1. Machine type
2. Machine serial number
3. Year of manufacture
4. Enclosure protection class
5. Voltage
6. Number of phases with or without neutral
7. Frequency
8. Main fuse
9. Motor output
10. Electrical heating output
11. Max. output
1.3 Checking that the machine and manual correspond
Check that the type description on the rating plate corresponds with the type de-
scription on manual cover page. If manuals are missing, it is possible to order new
ones from the manufacturer or the local distributor. When ordering new manuals,
it is important to quote the machine number found on the rating plate.
S/N:
Model:
IP V
Mårdvägen 4, SE-352 45 VÄXJÖ, SWEDEN
!
M
1
2
~Hz A
kWkW
kW
3
69
4
75 8
0
11
1

WD-T60, WD-T60F, WD-T80, WD-T90 Rev. 4.0 (202007)
General instructions
4
1.4 EU Declaration of Conformity
A so-called EU Declaration of Conformity is provided on delivery of the machine.
1. Contact details of the manufacturer (Wexiödisk AB, Mårdvägen 4, SE-
35245 Växjö, SWEDEN, Tel.: [phone], Fax: [phone], E-
mail: [e-mail]).
2. Representatives of Wexiödisk AB.
3. Person responsible for the product’s documentation.
4. Year of manufacture of the product.
5. The EU Directives with applicable provisions to which all the machines,
special machines and accessories comply.
6. Harmonised standards for the Directives specified, and which the ma-
chines, special machines and accessories meet, wherever relevant.
7. Model designation and serial number of the machines, special machines
and accessories the document applies to.
8. Place and date with signature and name (in block letters) of the person re-
sponsible for ensuring compliance with legislation and regulations.
CE_16_2
1
2
3
5
6
7
7
7
8
6
6
6
4

WD-T60, WD-T60F, WD-T80, WD-T90 Rev. 4.0 (202007)
Safety instructions
5
2. Safety instructions
Read the chapter GENERAL INSTRUCTIONS carefully before starting work.
2.1 General information
The machine is CE marked, which means that it complies with the requirements
of the EU Machinery Directive with regard to product safety. Product safety
means that the design of the machine will prevent personal injury or damage to
property. The CE mark is only valid for an unmodified machine. Any damage to
the machine arising from failure to follow the instructions will invalidate the sup-
plier’s warranty and product liability.
Installation, repair and service must be carried out by a qualified professional in
accordance with applicable local and national regulations for water and sewage,
electricity, ventilation and steam work. In order to ensure electrical safety, com-
ponents may only be tested run in a regular place in the machine. We recommend
that the work is done by the manufacturer or a service company authorized by the
manufacturer.
To further improve safety during installation, operation and servicing, the operator
and the personnel responsible for installing and servicing the machine should
read the safety instructions carefully.
The machine’s electronics are sensitive to electrostatic discharge (ESD), which is
why a static electricity wristband must be used when handling the electronics at
all times.
Before the machine enters service, ensure that the personnel are given the nec-
essary training in handling and looking after the machine.
In order to avoid dangerous situations, the following must be followed:
• Switch off the machine immediately in the event of failure or malfunction.
• Make sure the machine is non-live before removing the cover plate. Turn
off the power using the power switch. If required, the switch must be locked
to prevent unintentional operation.
• Allow the machine to cool.
• The machine and equipment requires an annual service. The machine
should be serviced by a person authorised or trained to do so by us. Use
original spare parts.
• Warranty repairs must be performed by an authorised company. Contact
an authorised service company to draw up a programme of preventive care
and maintenance. For authorised service companies, please see
www.wexiodisk.com or contact Wexiödisk AB.
• The regular checks described in the manual must be carried out in accord-
ance with the instructions.

WD-T60, WD-T60F, WD-T80, WD-T90 Rev. 4.0 (202007)
Safety instructions
6
2.2 Transport
If the drying zone is delivered as a separate unit, handle the equipment with care
during unloading and transport to avoid the risk of it tipping over. Never lift or
move the drying zone without using the wooden packaging to support the equip-
ment.
2.3 Installation
• The machine is designed for quick electrical installation.
• The machine must be connected to a lockable power switch.
• Make sure that the mains voltage is the same as that indicated on the ma-
chine’s rating plate.
For increased safety, it is recommended to equip the installation with a ground
fault circuit interrupter.
2.4 Operation
Be very careful around the machine when it is in operation.
2.4.1 High temperatures
To prevent risk of burn injuries, do not insert your fingers in the air gaps in the top
section of the drying zone.
2.4.2 Risk of crushing
For drying zones equipped with loading cradles, the cradle's forward and back-
wards movement may cause crushing injuries at the machine's outfeed opening.
2.4.3 Risk of slipping
The floor should be kept clean and dry to eliminate any risk of slipping. Mop up
any water and leftover food that has been spilt.
2.4.4 Sounds
The machine is not silent during operation, see TECHNICAL SPECIFICATIONS.
Hearing protection may therefore need to be used.
2.5 Cleaning the machine
The drying zone does not normally require cleaning. If there is any dirt on the dry-
ing zone's bottom plate, this should be rinsed off using a hose only.

WD-T60, WD-T60F, WD-T80, WD-T90 Rev. 4.0 (202007)
Installation instructions
7
3. Installation instructions
Read the chapters GENERAL INSTRUCTIONS and SAFETY INSTRUCTIONS
carefully before starting work.
3.1 General information
Read these instructions carefully, as they contain important information regarding
the correct installation method. The installation instructions apply to new installa-
tion of the dishwasher and drying zone when the equipment is delivered separate-
ly and the drying zone is supplied as a separate unit.
• The instructions should be used together with the machine’s wiring dia-
gram.
• The machine can be equipped with a number of different options. Certain
options may be standard in a number of countries. Check what your ma-
chine is equipped with.
• If holes need to be drilled in the machine, the holes must be fitted with an
edge strip or similar protection.
3.2 Requirements for the installation site
The requirements for installation of the drying zone are the same as for the dish-
washer to which it is connected. (Refer to the dishwasher's installation and user
manual.)

WD-T60, WD-T60F, WD-T80, WD-T90 Rev. 4.0 (202007)
Installation instructions
8
3.3 Transport and storage
Take care during transport, as there is a risk of tipping. N.B.: The drying zone
must not be transported without a pallet or other support. Otherwise, the drying
zone may become damaged.
The drying zone must be transported using a pallet for support (A)
If the drying zone is not to be installed immediately, it must be stored in a frost-
free area where the air is dry.
3.4 Unpacking
Check that all parts have been delivered by comparing them with the delivery
note.
Remove the packing material. Inspect the machine for any transport damage.
Packaging must be sent for destruction or recycling in accordance with local reg-
ulations.
WDT60_3
A

WD-T60, WD-T60F, WD-T80, WD-T90 Rev. 4.0 (202007)
Installation instructions
9
3.5 Installation
3.5.1 Preparing for the installation
Check that there is sufficient room for the machine at the installation location.
• Check that correct connections are available for water, electricity, drainage
and possibly steam at the installation location. See TECHNICAL SPECIFI-
CATIONS.
• Check that the fuse for the machine at the site is off, blocked and that out-
going electrical circuits from the machine are non-live.
• Remove the protective plastic on the sides which are to be stood against a
wall.
3.5.2 Assembling drying zone WD-T80
For connection to machines located above turn track WD-BF90/180 or WD-C90/
180.
• Remove the top panel (4).
• Use a lifting device during installation. Take care not to damage the drying
zone.
• The drying zone is secured to the dishwasher in the following way:
• Connecting to (1). M4 screw, nut and washer around the opening.
• Connecting to (2). M6 nut and washer.
• The hanging bar (3) is connected to a hole in the end plate of the machine's
electrical cabinet, with the flat bar (5) attached to the inside of the end plate.
Check that the drying zone is horizontal before securing it in place using
two nuts (M8), one on either side of the electrical cabinet's end plate. The
lock nut should be fitted inside the electrical cabinet.
• The electric cable is drawn through the hole between the drying zone and
the machine's electrical cabinet.
• Fit the top panel (4) and the curtain (6).
WDT60_7
1
24
5
6
3

WD-T60, WD-T60F, WD-T80, WD-T90 Rev. 4.0 (202007)
Installation instructions
10
3.5.3 Assembling drying zone WD-T60 and WD-T90
Drying zone WD-T90 is always delivered with a stand. The stand may optionally
be equipped with a grid shelf or grid plate.
A stand is available as extra equipment for WD-T60, which may be equipped with
a grid shelf of grid plate as an optional extra.
The drying zone is assembled first followed by the stand.
• Remove the top panel (9).
• Use a lifting device during installation. Be careful not to damage the bottom
plate.
• The top edge of the plate (4) has a slight outward bend in it. The part that
is bent outwards is inserted under the cover strip on the bottom edge of the
dishwasher's outfeed opening. Check that the gasket (3) is in place.
• The drying zone is secured to the dishwasher in the following way:
• Connecting to (6). M4 screw, nut and washer around the entire opening (to
install the T90 drying zone, an M6 screw, nut and washer are used in the
hole above the opening, everything else is M4).
• Connecting to (8). M6 nut and washer.
• Connecting to (2). M4 screw, nut and washer.
• Connecting to (5). M4 screw, nut and sealing washer (two connection
points).
• The loading cradle is connected to the machine at (1) with an M6 screw,
nut and washer.
WDT60_6
54321
6
7
8910
11
12

WD-T60, WD-T60F, WD-T80, WD-T90 Rev. 4.0 (202007)
Installation instructions
11
When the drying zone is in place, the stand can be installed.
• Screw the legs (11) on to the stand so that it can be inserted under the dry-
ing zone.
• The stand is fixed to the underside of the machine at (12) as well as to the
underside of the drying zone at (10) with an M6 nut and washer.
• Adjust the legs on the stand.
• The electric cable is drawn through the hole between the drying zone and
the machine's electrical cabinet.
• Fit the top panel (9) and the curtain (7).
3.5.4 Assembling drying zone WD-T60F
To be fitted to a roller table (supplied by WD). The connection to the dishwasher
has a separate electrical connection.

WD-T60, WD-T60F, WD-T80, WD-T90 Rev. 4.0 (202007)
Installation instructions
12
3.6 Connections
3.6.1 Electrical connection
Cabling between the drying zone and the dishwasher is connected using existing
holes in the end plate of the dishwasher's electrical cabinet (WD-T60, WD-T80
and WD-T90).
Electrical cabinet for drying zone located in dishwasher (WD-T60, WD-T80 and
WD-T90)
For cabling from the WD-T60F free-standing drying zone, cables are drawn
though an existing plugged hole at (C) on the dishwasher's outfeed side. The
electric cable is drawn through the cable duct behind the front panel (B) and on
to the electrical cabinet (D).
N.B.: If a new hole needs to be drilled at (C), this must be done carefully as there
are electric cables inside the plate.
Drawing cables from a free-standing drying zone
A=Drying zone WD-T60F
B=Front plate
C=Plugged hole or newly drilled hole for cable
D=Electrical cabinet

WD-T60, WD-T60F, WD-T80, WD-T90 Rev. 4.0 (202007)
Installation instructions
13
3.7 Trial operation
Prepare the machine for trial operation with the help of OPERATING INSTRUC-
TIONS. The instructions describe the measures that must be taken to prepare the
machine for operation.
3.7.1 Start-up schedule
This should be completed when the machine is started up and used.
Read the installation and user manuals carefully. Then check the following points:
1. Start the dishwasher and load baskets containing dishware Perform the
following checks:
• The direction of rotation of the fan(s).
• The curtain is in place.
• The washed items are dry.
2. Final check
• Turn off the power at the main switch and re-tighten the connections on cir-
cuit breakers and contactors.
3. Train the dishwashing personnel
• Care (daily, weekly and other frequencies)
• Recommendation for annual service
3.8 Documentation
For correct use and servicing, it is essential that the documentation accompany-
ing the machine is made available to personnel who will be using the machine.
The installation and user manual, which describes handling and care among oth-
er things, should be stored near the machine.
Machine type:
Machine serial number:
Installation date:

WD-T60, WD-T60F, WD-T80, WD-T90 Rev. 4.0 (202007)
Operating instructions
14
4. Operating instructions
Read the chapters GENERAL INSTRUCTIONS and SAFETY INSTRUCTIONS
carefully before starting work.
This chapter describes what must be done with the machine:
• Before washing
• How washing should be performed
• After completed washing
• In the event of error messages and troubleshooting

WD-T60, WD-T60F, WD-T80, WD-T90 Rev. 4.0 (202007)
Operating instructions
15
4.1 Preparations
Drying zone versions
1. Straight drying zone WD-T60 for positioning at the machine’s outfeed
opening.
2. Straight drying zone WD-T60F for free-standing positioning on the roller ta-
ble.
3. 90° angle drying zone WD-T80 for positioning at the machine's outfeed
opening on a 90°or 180°turn track.
4. Straight drying zone WD-T90 for positioning at the machine’s outfeed
opening.
5. Curtain
6. Bottom plate
7. Roof cover
Check:
• That the equipment is clean.
• That the curtain (5) is in position.
• That the roof cover (7) is in position.

WD-T60, WD-T60F, WD-T80, WD-T90 Rev. 4.0 (202007)
Operating instructions
16
4.2 Using the machine
The drying zone is controlled from the dishwasher and operates when the dish-
washer is feeding baskets through the machine.
The free-standing drying zone WD-T60F (2) only starts once a basket activates
an impulse arm in the zone. The zone stops automatically once there are no
morebaskets going through.
4.3 After use – Cleaning
HACCP is a preventive inspection system to ensure hygiene requirements are
met during the washing process and cleaning of the machine. As a result of its
design, the machine meets strict hygiene requirements. Regular, thorough clean-
ing is also important from a hygiene perspective. A machine that is properly
cleaned helps produce a good wash result, reduces the risk of dirt accumulating,
increases the service life of the machine and reduces the risk of emergency shut-
down.
4.3.1 Incorrect cleaning methods
N.B.: An incorrect cleaning method may damage the machine. The following
points must be observed:
• Do NOT use steel wool as it will cause corrosion to form on the machine.
• If detergent is used, it must not contain abrasives. Detergents containing
abrasives will damage the stainless steel panels.
• The exterior of the machine must not be hosed. Water can enter the ma-
chine and damage the control panel and electrical equipment.
• Pressure washers and steam can damage the machine and must NOT be
used for cleaning purposes. Never use a pressure washer to clean the floor
within 1 metre of the machine. The supplier cannot be held liable for any
faults caused by the use of pressure washers on the machine and any such
use may invalidate the warranty. There is a risk of splashing even if the
floor is hosed down.
Steel wool and pressure washers must not be used for cleaning
WD9_07