Whale Digital Smoothflow Instruction sheet

WARNING
Installation guidelines for
Models: Digital Smoothflow Kit
This booklet should be given to the customer after installation and demonstration
For illustration purposes only
Always t Earth straps to Sensors (See page 9 for diagram)
For information on the Digital Smoothow set-up please see www.whalepumps.com/psd - Resources Section.
The control unit
precisely matches
the pump speed to
the shower flow rate.
2
The matched pump
speed and shower
flow rate ensures
a quiet gulley.
3
The flow sensors measure
the flow rate going to the
shower head.
This information is
sent to the control unit.
1

2
This kit has been designed for the pumping of shower
waste water.
• When the shower is turned on the ow sensor(s)
measure the ow rate of the water into the shower.
• The pump speed is controlled directly from the control unit
which uses the signals sent from the ow sensor to adjust
the pump speed to match the ow from the shower.
• This minimises suction noise at the gulley. A simple setup is
required to match the pump performance to the
characteristics of the installation.
• When the shower is nished the pump will automatically
switch on after 15 minutes to remove any water pooled in
the showering area.
• The pump has the ability to run dry without causing
damage to the pump.
• Before installation please read the instructions.
• Plumbing installation must comply with the plumbing
regulation as specied in the latest WRAS leaet for
plumbing systems.
• The electrical wiring must conform to
BS7671: 2008 Part 7 (17th Edition).
• Contact the Technical Helpline
(0845 0694 253) if you need further assistance.
The front cover illustrates the product in typical Digital
Smoothflow installations (Mixer Shower Installation).
Assess your installation prior to fitting so as to ensure
that the pump, Digital Smoothflow Control Box and flow
sensor(s) will be situated in an accessible position.
Typical installations would have these components in an
adjacent cupboard i.e. airing cupboard or in a false wall
with an access panel.
Incorrect installation may invalidate
the warranty.
Index
Principles of Operation 2
Installation warnings 3
List of Parts included in kit 3
Additional Parts 3
Plumbing Specication 4
Plumbing Gulley 5
Plumbing of Waste Pipe 6
Pump Mounting Instructions 7
Digital Smoothow Mounting Instructions 8
Digital Smoothow System Layout 9
Flow Sensor Plumbing Connections 10
Flow Sensor Electrical Connections 11
Pump Set-up – Electric Shower 15mm (1) 12
Pump Set-up – Electric Shower 15mm (2) 13
Pump Set-up – Electric Shower 15mm (3) 14
Pump Set-up – Mixer Shower 22mm (1) 15
Pump Set-up – Mixer Shower 22mm (2) 16
Pump Set-up – Mixer Shower 22mm (3) 17
Pump Set-up – Mixer Shower 22mm (4) 18
Safety Warning 19
Specication 19
Aftercare 19
Warranty 19
EU Declaration of Conformity 19
Illustrations
1.1 90mm Gulley 3
1.2a Top Suction Fitting 3
1.2b Venturi Sensor 3
1.3 Plumbing Layout 4
1.4 Pump Orientation 4
1.5 Rotation of Pump ead 4
1.6 Clamping Ring Fixing 6
1.7 Tray Gulley Installation 5
1.8 Tray Gulley Installation – and Tool 5
1.9 Tray Gulley Installation – Gulley Cover 5
2.0 Wet Floor Gulley Installation 5
2.1 Plumbing ‘Waste Fittings’ 6
2.2 Macerator Connections 6
2.3 Pump Mounting Instructions 7
2.4 Digital Smoothow Mounting Installations 8
2.5 Digital Smoothow System Layout 9
2.6 Venturi Sensor 10
2.7 Venturi Sensor Connections 11
WARNING
Principles of Operation

3
Item Part o. Qty
Shower Drain Pump SDS021T 1
Pump Cover Base 755.178 1
Pump Cover 755.177 1
Digital Smoothow Control Unit SDS243T 1
Venturi Flow Sensor SDS223T 1
Tray Gulley 1
c/w tting tool and cover
Wet Floor Gulley 1
c/w clamping ring and cover 1
Tricuspid Valve older 755.309 1
Tricuspid Valve 755.57 1
Rubber Waste Adaptor 2 part, 1
22 mm-1½” tting
22 mm-22 mm tting 1
22 mm-15 mm ttings 2
Fitting kit 1
Before installation read the instructions
All electric and mechanical components (control unit, pump
and ow sensors) must be accessible after installation.
• The maximum ow rate the pump is design to work with is
8 Itrs/min for 15mm (electric shower) and 12 ltrs/min for
22mm mixer shower installations.
• Avoid plumbing the pump outlet into the waste piping that
other appliances drain into as there is a risk of induced
syphoning. Use an anti syphon trap in these situations.
• With installations where the oor is being formed in the
screed, we recommend the following minimum falls:
30mm in 1m, 15mm in 500cm, 7.5mm in 250cm.
• Plumbing installation must comply to latest WRAS
regulations.
• The electrical wiring must conform to EU wiring regulations
BS7671:2008 Part 7 (17th Edition).
User Warnings
• It is advisable where the property is unattended for an
extended period that the water supply to the shower
is shut off.
• If there is a reduction in pump performance after installation
please contact your installer.
These parts are not supplied with the kit and may be ordered
from your distributor or stockist:
Part No.
• 90 mm Gulley AK1695
(O/A dimensions 64 mm h x 111 mm dia)
See Fig 1.1
• Top suction tting John Guest part number
PEM221515W (Stem Elbow) See Fig 1.2a
Not recommended for Digital Smoothow
Spare Parts and Kits
• Venturi Flow Sensor See Fig 1.2b SDS223T
• Shower Drain Pump SDS021T
• Tricuspid Valve Qty 10 SDS211B
• Pump ead Replacement Kit SDS071T
(including diaphragm and tricuspid valve)
• Diaphragm and Tricuspid Valve Kit SDS061T
List of Parts included in kit
Installation Warnings Additional Parts
1.1
1.2a
1.2b
WARNING
WARNING

1.3
4
• Mount pump, head down, as shown. See Fig 1.4
• Mount the pump on a solid wall to prevent vibration.
Note: If mounted to a stud wall pump vibration may cause noise through
the resonance of the wall. In these situations mount the pump on a
bracket off the oor. The pump may be mounted horizontally on the oor
if required.
• The shower oor must have a fall of at least 1:40.
• Pump, ow sensor and control box must be
accessible after installation.
• Use a maximum of one vertical lift to the pump and
one vertical rise from the pump. See Fig 1.3
• The pump inlet should point towards the gulley and
the gulley outlet should point towards the pump to
keep connecting pipework as straight as possible.
• Rotate the pump head if necessary to connect the
gulley to the pump by the most direct route. Loosen
clamping ring screw, rotate and retighten as shown.
See Fig 1.5 and 1.6
• Do not combine pump discharge with other
appliances as there is a risk of induced syphoning.
Use an anti-syphon trap where necessary.
• Whale®pump is IP45 compliant. Locate pump in
accordance with BS7671: 2008 part 7 (17th Edition).
The pump may be installed in zones 1, 2 or 3.
• Electric Shower Installation – Maximum ow rate
8 ltrs/min, (15mm pipework on the inlet to the pump/
22mm pipework on the outlet).
• Mixer Shower Installations – Maximum ow rate
12 ltrs/min, (22mm pipework on the inlet to the pump/
22mm pipework on the outlet).
Note - An additional ow sensor ( art No. SD 223T) and 22 mm
ttings are required.
• Use slow radius bends where possible. Use formed
bends or elbow ttings – not stem elbows.
• Inserts should not be used with plastic waste pipe.
• Ensure pipe edges are burr-free.
• Pipework must be secured.
• Push home pipe into push-t ttings and
‘Twist Lock’. Do not stress pipe at connection.
Plumbing Specification
1.4
1.5 1.6
Maximum pipe length for typical installation
- extra elbows will reduce performance.
ipe from gulley to pump must be 15mm for
electric shower installations and 22mm for
mixer valve installations. Failure to do this
will effect pump performance.
WARNING

5
• Before running water through the system ensure that
the shower area and gulley are completely free of debris.
• For pump mounting instructions. See Fig 2.3, Page 7
Orientate gulley so that it exits towards the pump inlet
to avoid unnecessary bends.
• When tting in solid oors if copper pipe is used, it must be
sheathed to prevent corrosion.
Tray Gulley
• The tray gulley has a 35 mm prole to enable the shower
drain to t into a screed oor without penetrating the
damp-proof membrane. See Fig 1.7
• Use silicone on top of the seal to ensure proper sealing
beneath tray.
• Use the hand tool provided to tighten the locking ange.
See Fig 1.8
• Fit the gulley cover into the sockets and push down to
secure. See Fig 1.9
Wetoor Gulley
• The wet oor gulley has a 40 mm prole to enable it to t
into a screed oor without penetrating the damp-proof
membrane. See Fig 2.0
• Where no tray former is used the gulley has two lugs either
side of the discharge pipe to enable the gulley to be xed
to the oor whilst screed is laid around the gulley.
• Where a tray former is used these lugs can be broken off
easily and the gulley mounted into the
160 mm gulley opening.
• The gulley has a conventional clamping ring to
accommodate vinyl ooring.
• The gulley cap clicks into place and may be easily removed
for cleaning if required.
Other Gulley’s
• The pump may be used with gravity style gullies. Use
reducing couplings to achieve 22mm pipe run to pump.
Top Tip: Leave the hand tool in place to prevent building debris,
grout etc. falling into the gulley. Only remove the hand tool and t
the gulley cover when the installation is complete and the shower
area has been thoroughly cleaned.
Plumbing Gulley
1.7
1.8
1.9
2.0

6
• The outlet of the pump may be connected into the
waste pipe, e.g. former bath waste. Black rubber
ttings are provided for this.
• In conned bathrooms pump discharge may go into
the sink waste pipe using suitable adaptors.
See Fig 2.1 for McAlpine examples and their catalogue for
other variants.
Use with a Macerator Pump
• Discharge from the Whale pump must go into the
top of the macerator box. Do not use the bottom entries.
See Fig 2.2
• It is preferable to have two separate discharge lines
to waste as any failure of the macerator will not be
detected by the Whale pump.
• Avoid plumbing the pump outlet into the waste piping that
other appliances drain into as there is a risk of induced
syphoning. Use an antisyphon trap in these situations.
From pump
C10 V33T
Plumbing of Waste Pipe
2.1
2.2

7
Us th backplat as a
t mplat to mark th position
of th mounting hol s.
Us a 6 mm bit to drill hol s
at mark d points and ins rt
No 6 wall plugs.
Us pli rs to op n up d sir d cabl ntry
point on backplat . Don’t us top c ntr
ntry. X = DO NOT USE
To t cov r, locat bottom lug into
backplat , and pivot cov r forward until
top clips click into plac .
To r mov cov r, us two hands to push backplat clips tog th r.
As clips dis ngag , th cov r will fall forward and may b lift d away.
If th pump is misalign d on th backplat
or pump h ad is not parall l with backplat
th push-t conn ctors may pr v nt th
front cov r from tting prop rly. Adjust
pump, pump h ad or conn cting pip work
to achi v a good t.
Us of lbows on pump inl t and outl t
should b avoid d. If th situation d mands
that th y ar us d, ONLY us John Gu st
push-t lbows. Oth r typ s ar not r adily
d mountabl and may foul th cov r.
Fix pump to wall using No 8 scr ws. Us crimps suppli d to t rminat 24V d.v.
cabl from transform r, conn ct to pump and f d cabl through ntry point.
Hold cabl in plac using adjac nt cabl brack t.
Pump Mounting Instructions
2.3

8
1.6 Location of Control Unit:
• Locate the control unit outside the showering area in
accordance with BS7671: 2008 Part 7 (17th Edition).
See Fig 2.4
• The control unit is IP45 compliant.
• Tighten all cable entry grommets, even unused ones, to
seal the Control Unit.
• Connect Control Unit to 240V a.c. supply via an
unswitched 5 amp fused spur.
Digital Smoothflow Mounting Instructions
2.4

9
Digital Smoothflow System Layout & Earthing Configuration
2.5
ote: Earthing Tag to be connected
to metal part of the venturi sensor
with the earthing cable run directly
back to control unit’s earth tag.
Earth wire must be 1.5mm2.
ote: Mixer Valve Shower
installation illustrated. Only one
ow sensor is required in an
Electric Shower installation
Earth wires
Earth clamps and sensor to be
earthed back to control unit
WARNING
Earth Tag

10
• Fit the Flow Sensors with the arrow in the
direction of ow to the shower, downstream of any other
connections to the water supply.
• Ensure ow sensor(s) is accessible.
• The ow sensor(s) must be mounted in a straight length of
unstressed pipe.
• For the Venturi sensor(s) a lter is not required.
See Fig 2.6
Note: For a mixer shower installation place the ow sensors in the
hot and cold supply as described above. (The Digital Smoothow is
supplied with one ow sensor, for additional ow sensor please order
art No. SDS223T).
Commissioning Checklist
• Ensure all pipes are pushed home into the push t
ttings and are locked.
• Check all plumbing for leaks whilst the pump is running.
• Ensure ow sensor(s) is tted in a length of
unstressed pipe.
After completing the set up turn on the shower and check for
correct operation and that noise has been minimised.
ote:
• Mixer valve installations require two sensors. The sensors
must be identical.
Venturi Sensor
Flow Sensor(s) Plumbing Connections
2.6

11
• Switch off the power to the control unit before
making connections.
• Feed wires through cable grommets prior to
connection to the control unit.
• Strip wires 10 mm and twist prior to inserting into
spring loaded contacts. Do not use tinned wire.
• Push contact arm back with a nger or small
screwdriver before inserting wire fully and
then release.
• Check for a good connection by giving a gentle
tug on the wires.
• Tighten cable grommets after connection.
Wiring Connections:
1) Flow Sensor to Digital Smoothow Control Box -
Connect the ow sensor(s) as shown
(For cold supply use FS A and for hot supply
use FS B):
Venturi Sensor(s) See Fig 2.7
- Brown wire to Power (PWR)
- White to Signal (SIG)
- Green to Ground (GND)
2) Pump to Digital Smoothow Control Box –
Connect pump supply wires as shown:
- Black wire to PUMP BLACK
- Red wire to PUMP RED
Avoid fouling the insulation when crimping to the pump supply
wire or making connections to the mains supply.
WARNING
Flow Sensor Electrical Connections
2.7
Do not coil sensor cable.
Use a straight run cut to size.
Sensor cable: Yellow wire is for temperature and is unused
Venturi
Sensor
Connections

12
A simple setup is all that is required for trouble-free efcient
performance of the Digital Smoothow system.
To adjust Settings:
or These buttons switch between menu
options, indicated by the LCD message.
or These buttons adjust the value.
The OK or Enter key (middle button) press to select and
store value.
Press OK ‘ ’ to enter conguration screens.
Follow the sequence of screens and set values as
required to complete setup.
System Type and Software level
Settings
1. Language: English is the default language. For
other options use or arrows.
Press OK ‘ ’ to select.
2. Pipe size: Select 15mm for electric showers.
(Go to Page 15 for Mixer Set-up)
Press OK ‘ ’ to select.
3. Sensor type: Select Venturi
Press OK ‘ ’ to select.
4. Pump speed: This enables the speed of the pump to
match the shower ow rate.
Before making adjustments turn the shower on and wait until
the pump runs. Set the shower ow rate in the range 4 -7
ltrs/min as indicated on the display. The rate should remain
unchanged during set-up. Use or to set the speed of the
pump to match the ow rate.
Watch the level of water within the shower using the gulley
cover as a guide. If the water level is falling reduce the speed
of the pump by pressing . If the water level rises increase the
speed of the pump by using the button.
Note: After making a change wait for about ‘30’ seconds, as the
system needs to stabilise. Watch the water level until you see if the
water is rising or falling before making the next adjustment.
Initially make changes in pump speed setting in increments
and decrements of 5 to quickly get to an approximate pump
speed that matches the ow rate. Once this is achieved make
ner adjustments, up or down, until the water level is slightly
over pumping. Store the speed setting by pressing OK ‘ ’.
The pump will stop whilst the setting is stored, and start again
at the set speed.
Smoothflow V1.9
o S e t u p P r e s s ↵
I n l e t P i p e O K ↵
S i z e 1 5 m m
A 3 . 5 B 0 . 0 3 . 5 L P M
P u m p S p e e d 0 ↵
S e n s o r O K ↵
y p e V E N U R I
L a n g u a g e O K ↵
English
Pump Set up – Electric Shower 15mm (1)

13
5. Pump shut down: Over Run (Auto-Sense) is the
preferred option. Auto-Sense stores the pump no-load
current when air is drawn by the pump after water is removed
from the tray. Once set, when this value is reached the pump
will go into its shut down sequence.
Time Delay is the default setting. To set Auto Sense press
then press OK ‘ ’ to select.
Turn off the shower. When the pump has removed the water
remaining in the tray the pump current will decrease. When it
has reached the lowest value
(by observing when the value stops falling)
press OK ‘ ’.
Pump will run on for a few seconds before stopping
Over Run (Time-Delay)
This sets a xed Over Run time that the pump continues to
run after the shower has been turned off.
Use or to select value of time delay (in seconds) and
press OK ‘ ’ to store.
6. Start volume: This selects the initial amount of
water (litres) in the tray before pumping starts. To
minimise noise the water should be above the level
of the gulley.
(Factory default is 0.6 ltrs, minimum setting).
Pressing increases the amount of water from 0.6
ltrs to 4 ltrs. Typical value between 0.8 and 2 ltrs.
Press OK ‘ ’ to select.
7. Purge Cycle: When ON is selected the pump
restarts 15 minutes after showering is completed.
This happens automatically to remove water that
gathers as it drains into the gulley . The pump
runs at a low speed for less than 30 seconds.
Press OK ‘ ’ to select.
If desired the Purge Cycle may be disabled by pressing and
OK ‘ ’ to select OFF.
Factory Default Settings
If part way through set-up and you wish to start
again, turn the unit off until the display fades, and
then back on again. The screen will display:-
System Type and Software level
Press OK ‘ ’ to begin again. The screen will start at language
options. See page 12.
Over-Run OK↵
y p e I M E - D E L A Y
Over-Run OK↵
y p e A U O - S E N S E
P u m p C u r r e n t 8 6
L i m i t O K↵0
O f f D e l a y O K ↵
i m e 1 0 s e c Smoothflow V1.9
Review> Adjust↵
P u r g e C y c l e O K ↵
1 5 m i n C y c l e O N
S t a r t D e l a y O K ↵
Volume 0.6Ltrs
Pump Set up – Electric Shower 15mm (2)

14
After completing the set up turn on the shower and check for
correct operation and that noise has been minimised.
Digital Smoothow Review Screens
The following are the status displays that may be scrolled
through by pressing when the pump is off. Note: To adjust
any of the pump settings press OK ‘ ’
System Type and Software level
Running time of pump
Standby time of pump
Inlet Pipe diameter 15mm for electric showers,
22mm for mixer valve installations
Flow Sensor Type Match to the type of sensor used.
Factory Default Settings
To return the unit to Factory Default settings start at the
System Type and Software level Screen.
Press then ve times to get to factory default prompt.
Press to select ‘YES’ and OK ‘ ’ to conrm. The message
‘Are You Sure?’ will appear. Press to select ‘YES’ and OK
‘ ’ to conrm. The unit will then be reset to default settings.
Smoothflow V1.9
Review> Adjust↵
O n i m e n e x t >
6hrs 23min
S m o o t h f l o w V 1 . 4
R e v i e w > A d j u s t ↵
F l o w S e n s o r e x i t >
y p e V E N U R I
S t a n d b y n e x t < >
456hrs 23min
I n l e t P i p e n e x t < >
D i a m e t e r 1 5 m m
Pump Set up – Electric Shower 15mm (3)

15
A simple setup is required for trouble-free efcient
performance of the Digital Smoothow System.
To adjust Settings:
or These buttons switch between menu options, indicated
by the LCD message.
or These buttons adjust the value.
The OK or Enter key (middle button) press to select and store
value.
Press OK ‘ ’ to enter conguration screens. Follow the
sequence of screens and set values as required to complete
setup.
System Type and Software level
Settings
1. Language: English is the default language.
For other options use or arrows.
Press OK ‘ ’ to select.
2. Pipe size: Press to select 22mm for
\mixer valve installations.
Press OK ‘ ’ to select.
3. Sensor type: Select Venturi
Press OK ‘ ’ to select.
4. Pump speed: This enables the speed of the pump to
match the shower ow rate.
Before making adjustments turn the shower on and wait until
the pump runs. Set the shower ow rate in the range 7-9
ltrs/min as indicated on the display. The rate should remain
unchanged during set-up. Use or to set the speed of the
pump to match the ow rate. Watch the level of water within
the shower using the gulley cover as a guide. If the water level
is falling reduce the speed of the pump by pressing . If the
water level rises increase the speed of the pump by using the
button.
Note: After making a change wait for about ‘30’ seconds, as the
system needs to stabilize. Watch the water level until you see if the
water is rising or falling before making the next adjustment.
Initially make changes in pump speed setting in increments
and decrements of 5 to quickly get to an approximate pump
speed that matches the ow rate. Once this is achieved make
ner adjustments, up or down, until the water level is slightly
over pumping. Store the speed setting by pressing OK ‘ ’.
The pump will stop whilst the setting is stored, and start again
at the set speed.
Smoothflow V1.9
O S E U P P R E S S ↵
Language OK↵
English
Inlet Pipe OK↵
S i z e 2 2 m m
S e n s o r O K ↵
y p e V E N U R I
A 3 . 1 B 5 . 6 8 . 7 L P M
P u m p S p e e d 0 ↵
Smoothflow
Pump Set up – Mixer Shower 22mm (1)

16
4. Pump speed - Fine setting:
This setting may be required to ne tune the speed at ow
rates other than that used to set the main ow rate. The Fine
Speed adjustment corrects the ow rate over a band 1 ltr/min
either side of the ow rate that is being calibrated.
Increase the ow from the shower to its maximum value (less
than 12 ltrs/min) in 2 ltrs steps. Watch the water level around
the shower gulley. If this is rising or falling over time make
adjustments until a constant level is observed then press OK
‘’. The pump will not stop but the adjustment displayed will
return to ‘0’
Now reduce the ow rate to minimum (approx 3 ltrs/min).
Again adjust as required to keep the water level around the
gulley constant or just falling slightly. Once this adjustment is
made press OK ‘ ’ to select.
Adjustments to more nely matched ow rates or special
features of the shower, i.e. Boost settings, can be made if
required.
Once complete press > to exit and move onto the
next stage.
6 . 6 B 5 . 4 ( 1 2 . 0 ) L P M
F i n e S p e e d 3 ↵
A 2 . 4 B 1 . 5 ( 3 . 9 ) L P M
F i n e S p e e d 0 ↵
Pump Set up – Mixer Shower 22mm (2)

17
5. Pump shut down: Over Run (Auto-Sense) is
the preferred option. Auto-Sense stores the pump no load
current when air is drawn by the pump after water is removed
from the tray. Once set, when this value is reached the pump
will go into its shut down sequence.
Time Delay is the default setting. To set Auto Sense press
then press OK ‘ ’ to select.
Turn off the shower. When the pump has removed the water
remaining in the tray the pump current will decrease. When it
has reached the lowest value (by observing when the value
stops falling) press OK ‘ ’.
Pump will run on for a few seconds before stopping
Over Run (Time-Delay)
This sets a xed Over Run time that the pump continues to
run after the shower has been turned off.
Use or to select value of time delay (in seconds) and
press OK ‘ ’ to store.
6. Start volume: This selects the initial amount of water (litres)
in the tray before pumping starts. To minimise noise the water
should be above the level of the gulley.
(Factory default is 0.6 ltrs, minimum setting). Pressing
increases the amount of water from 0.6 ltrs to 4 ltrs. Typical
value between 0.8 and 2 ltrs. Press OK ‘ ’ to select.
7. Purge Cycle: When ON is selected the pump restarts 15
minutes after showering is completed.
This happens automatically to remove water that gathers as it
drains into the gulley . The pump runs at a low speed for less
than 30 seconds.
Press OK ‘ ’ to select.
If desired the Purge Cycle may be disabled by pressing
and OK ‘ ’ to select OFF.
Factory Default Settings
If part way through set-up and you wish to start again, turn
the unit off until the display fades, and then back on again.
The screen will display:-
System Type and Software level
Press OK ‘ ’ to begin again. The screen will start at language
options. See page 12.
Over-Run OK↵
y p e I M E - D E L A Y
Over-Run OK↵
y p e A U O - S E N S E
Pump Current 86
OK↵0
O f f D e l a y O K ↵
i m e 1 0 s e c S m o o t h f l o w V 1 . 9
Review> Adjust↵
P u r g e C y c l e O K ↵
1 5 m i n C y c l e O N
S t a r t D e l a y O K ↵
V o l u m e 0 . 6 L t r s
Pump Set up – Mixer Shower 22mm (3)

18
Digital Smoothow Review Screens
The following are the status displays that may be scrolled
through by pressing when the pump is off. ote: To
adjust any of the pump settings press OK ‘ ’
System Type and Software level
Running time of pump
Standby time of pump
Inlet Pipe diameter 15mm for electric showers, 22mm for
mixer valve installations
The circuit board earth must be the same potential as the
water. Connect earth tag (as shown in the diagram) to
copper pipe or the metal part of the Venturi Sensor.
Flow Sensor Type Match to the type of sensor used.
Factory Default Settings
To return the unit to Factory Default settings start at the
System Type and Software level Screen.
Press ‘ ’ then six times to get to factory default. Press to
select ‘YES’ and to conrm. The unit will then be reset to
default settings prompt. Press to select ‘YES’ and OK ‘ ’
to conrm. The message
‘Are You Sure?’ will appear. Press to select ‘YES’
and OK ‘ ’ to conrm. The unit will then be reset to default
settings.
Earth Tag Connection
Smoothflow V1.9
Review> Adjust↵
O n i m e n e x t >
6 h r s 2 3 m i n
Smoothflow V1.9
Review> Adjust↵
F l o w S e n s o r e x i t >
y p e V E N U R I
Standby next<>
4 5 6 h r s 2 3 m i n
I n l e t P i p e n e x t < >
D i a m e t e r 2 2 m m
Pump Set up – Mixer Shower 22mm (4)
Earth tag

19
• The Digital Smoothow is designed for indoor use only.
• The Digital Smoothow control box contains no user
serviceable parts.
• Do not connect mains to the pump as this will cause
permanent damage and result in an electrical hazard.
• Installation must conform to BS7671: 2008 Part 7
(17th Edition).
Description of Equipment: Shower Drain System
Manufacturer’s Declaration
We hereby declare, under our sole responsibility, that the
above equipment complies with the provisions of the following
EC Directives. Electromagnetic Compatibility Directive
2004/108/EC, on the approximation of the laws of the
Member States relating to electromagnetic compatibility.
Low Voltage Directive 2006/95/EC on the harmonisation of
the laws of the Member States relating to electrical equipment
designed for use within certain voltage limits.
CE mark rst afxed: 01/01/96
Basis on which conformity is declared
The above equipment complies with the protection
requirements of the EMC Directive and the principal elements
of the safety objectives of the Low Voltage Directive.
For warranty details, please refer to the enclosed
copy of Whale's Statement of Limited Warranty.
Pump
Model: SDS021T
Dry running current: 1.2 amp
Maximum ead: 1.0 m
Maximum Lift: 500 mm
Maximum ead & Lift: 1.5 m
Digital Smoothow
Model: 755.241(Circuit Board 755.219)
Power rating 137VA
Double insulated
Mains cable 3.0m
3 core 0.75mm2; 6A
6.3 amp fast blow fuse
Whale’s policy is one of continuous improvement and we
reserve the right to change specications without prior notice.
The pump is maintenance free and does not normally
require any attention. If the pumping performance
reduces over time the following action may be taken:
• Clear inlet pipe of any debris or restriction caused by
soap or other matter adhering to the internal bore by
blowing, rodding or purging the pipe from the pump
end toward the gulley.
• Replace the tricuspid valve if it has become inexible
or damaged. Replacement can be purchased
Part No. SDS211B.
• Remove and rinse out, or replace pump head.
• The diaphragm and internal valves do not normally
require replacement. owever, if they become
damaged they may be replaced using the service kits:
Part No. SDS061T or SDS071T
Safety Warning Aftercare
Specification
EU Declaration of Conformity
Warranty
Standards applied
EN 60335-1:2001/A2:2006 Safety of household and similar
electrical appliances
EN 60335-2-41:2003/A1:2004 Particular requirements for
pumps
EN 55014-1:2000/A2:2002 Electromagnetic compatibility.
Requirements for household appliances, electric tools and
similar apparatus. Emission
EN 55014-2:1997/A1:2001 Electromagnetic compatibility.
Requirements for household appliances, electric tools and
similar apparatus. Immunity.
Signed
Richard Bovill, Engineering Director

20
Control Unit - SD 243T
ump - SDS021T