WheelChair Carrier Tilt N Tote 001 User manual

1
7325 Douglas Rd.
Lambertville, MI 48144
Phone: [phone]
Fax: [phone]
www.WheelChairCarrier.com
Tilt ‘N’ Tote [Model 001] , Tilt ‘N’ Tote Plus [Model 004] & Tote [Model 003]
Folding WheelChair Carrier
Installation Guide & Owners Manual
CAUTION: Read and follow all Installation Instructions and Operating Instructions before the first
use of this product.
Save this manual for future reference. Rev. Original 06-10-05 / Rev. E 04-04-11
Tilt ‘N’ Tote Plus [Model 004]
Tilt ‘N’ Tote [Model 001]
Hold down Arm
Securing Strap Assembly
Securing Strap Hook
Pull for Stow Away
Pull Pin B
Front Saddle
Pull to Tilt down and load chair
Pull Pin A
Base
Large Saddle
Tote [Model 003] Non folding

2
Introduction
Congratulations on your new WheelChair Carrier product purchase! The Tilt ‘N’ Tote carrier is the
easiest way to transport your folding wheelchair. The Tilt ‘N’ Tote Plus will accommodate folding
wheel chairs with 8” to 13” Diameter Wheels, and with a separate locking arm it can accommodate a
standard 24” folding wheelchair. The Tote is a space saving carrier for your wheelchair. This
manual has been written to be used as an installation guide as well as an operation guide for the end
user.
Both installers and operators should read all of the available manuals thoroughly before attempting
any installation, operation, or maintenance of the Tilt ‘N’ Tote carrier.
If you have any questions or comments concerning the installation or operation of this carrier, please
contact your local dealer or WheelChair Carrier for additional technical information.
DANGER: Some folding wheelchairs may be unsuitable for transport on a Tilt
‘N’ Tote carrier. Please be sure that the chair meets the size constraints set for each
product. Never exceed the posted weight capacity [100 lbs] of the carrier.
Unpacking the Carrier
Detailed below is the inventory of parts included with your carrier. If any parts are missing or if any
shipping damage is noted, immediately contact your dealer or WheelChair Carrier if purchased direct.
DO NOT attempt to install or use the lift with any missing or damaged parts.
Tilt ‘N’ Tote Carrier Box Contents:
•(1) – Carrier Assembly
•(1)– 15” Bungee Cord
•(1) – ¾-10 x 3-1/2” Hex Bolt
•(1) – ¾-10 Lock Nut
•(1) – ¾” Lock Washer
•(1) – Hold Down Arm
•(1) – Anti Rotation Bracket
oAccessories
022 Cover - Protects both wheelchair and carrier
302 Class 2 [1-1/4”] Ball Mount
½” Pin with Clip Included
303 Class 3 [2”] Ball Mount
5/8” Pin with Clip Included
Sold
Separately

3
Installation Instructions
•
The Tilt ‘N’ Tote carrier requires a minimum Class 1 trailer hitch with a Ball Mount. For proper
standard installation, any existing tow ball must be removed from the hitch. If you need assistance
in choosing the correct hitch for your vehicle, contact your local hitch dealer such as U-Haul®.
There are also many web sites on the internet that offer complete hitch guides and hitch search
engines using your specific vehicle information. Below are a few sites that may be helpful.
http://www.uhaul.com http://www.hitchfinder.com http://www.draw-tite.com
IMPORTANT: Every hitch bears a different amount of tongue weight.
NEVER exceed the tongue weight capacity of your hitch.
[Tongue weight = the weight of the carrier + the weight of the chair on the carrier.]
•
For the best performance, the carrier should be mounted at a height of 9 to 13 inches above the
ground. The Tilt ‘N’ Tote should be mounted at a height which is comfortable for lifting the
wheelchair off the ground. The carrier may be mounted either above or below the draw bar to ensure
proper ground clearance. If your carrier is equipped with a hitch adapter accessory then the accessory
can be rotated to achieve variable ground clearance.
•If using the anti-rotation bracket then place it above or below the draw bar. Make sure that the holes
on the anti-rotation bracket and the draw bar are aligned. The anti-rotation bracket must lay flat on
the draw bar.
NOTE: The carrier comes with a standard anti-rotation bracket to fit on a drawbar that measures under
2-1/2” wide. Please be sure to purchase this size draw bar when purchasing a trailer hitch. Some class 3
hitches have an extra wide drawbar that measures over 2-1/2” in width. If this size drawbar is
encountered, please contact your local dealer or WheelChair Carrier and the proper anti-rotation bracket
will be provided to you.
•After the carrier is installed make sure that it is secure and that the carrier does not move side to side.
•Make sure all of the pivot points and the latching mechanisms are properly greased and move
effortlessly.
•Make sure the unit easily tilts to the ground and folds up to the bumper of the vehicle.
SPECIFICATIONS:
Product Weight: 22 lbs
Maximum Capacity: 100 lbs
Class Hitch Required: 1, 2, or 3
Size Capacity: 15-1/2” x 29”
Works with: Standard Folding Wheelchairs
Recommended Hitch height: 9”-13”
Ball Mount
Anti-Rotation
Bracket

4
•
Tilt the carrier to the ground using Pull Pin-A. Roll the chair into the carrier so rear wheels are
contained in the large wire form saddle. Tip the chair and carrier forward until Pull Pin-A snaps
back into position.
•Secure the front wheels with the strap provided. Do this by putting the strap over or through the
front wheels. Make sure that both sides of the strap are secure. Double check the pull pin to
make sure it has snapped back into position.
•Insert the end of the Hold Down Arm into the base. The prongs of the Arm should be over the
back wheel of the chair. Insert the Securing strap hook over the 1” tubing. Pull the strap tight.
Do not over tighten the strap. This may cause the wheel to warp.
FRONT WHEEL ADJUSTMENT
After loading your chair into the carrier, slide the front saddle to the position that fits your chair.
Tighten the Bolts to secure the front saddle.
IMPORTANT: Always verify that the wheelchair is secure before operating the vehicle.
When not in use, the Tilt ‘N’ Tote can be folded up toward the bumper of the vehicle in its’ “stow away”
position.
•The carrier tilts up to the “stow away” position by pulling Pull Pin-B and rotating the carrier up
toward the vehicle.
•Make sure that Pull Pin-B snaps into the locking position and that the carrier is secure when in the
“stow away” position.
•The Hold Down Arm can be left in base with the securing strap fastened down, or removed to
store in trunk for storage.
Operation Instructions
Storing the Carrier
Carrying
Position Stow Away Position
[Not available on
the Model 003 tote]

5
Our wheelchair carriers have been designed to be as trouble free as possible for the owner. As with any
mechanical device however, maintenance should be performed regularly while owning and operating
our carriers.
•WheelChair Carrier recommends that dealers schedule a preventative maintenance inspection at
least once a year on the carrier frame, and all moving parts of the carrier.
•Regularly check and tighten all hardware on the carrier.
•Regularly check paint and touch up any bare metal with a good gloss enamel or lacquer to
inhibit rust. WheelChair Carrier recommends checking your carrier frequently if it is subjected
to salt air or road salt for any period of time.
Safety
Caution: Do not operate the carrier without being satisfactorily instructed in the
proper operation of the carrier by the dealer or without reading and understanding
the operation manual.
•
Our wheelchair carriers have been designed, engineered and tested for years of trouble free
performance. However, with everyday use some parts may become loose or worn. Regularly
inspect your carrier for any worn, loose, or damaged parts. If you find anything upon
inspection, DO NOT USE THE CARRIER! Contact your local dealer or WheelChair Carrier
for any repairs that need to be made. Failure to act may cause severe injury!
•Our wheelchair carriers must only be used for the loading and unloading of wheelchairs for
which it is designed. DO NOT add to or modify any part of the carrier system without first
contacting the manufacturer of the carrier. Any modifications may void any warranties as well
as compromise the structural integrity of the carrier.
Maintenance

6
3 YEAR TRANSFERABLE WARRANTY
Every effort has been made to insure high quality in material and workmanship of our
products. Manufacturer warrants all products to be free of defects in material and/or
workmanship for three (3) years from date of original purchase. EXCEPTIONS: All custom
orders have a 90~day warranty.
CARRIERS: All carriers are warranted to be free of defects in material and/or workmanship
for three (3) years from date of original purchase when used in accordance with manufacturer
installation and operating instructions. This warranty does not cover damage due to abuse,
misuse, accident, or use of unauthorized attachments or modifications. Protective finish coating
on carriers is not guaranteed in as much as the manufacturer is not responsible for the use
(abuse or natural wear and tear) of the product. The manufacturer and/or selling agents of
carriers will not be responsible in any way for damage to, or loss of, item(s) being carried or
falling from carriers or damages said item(s) may cause on or off carriers.
TRANSPORT COVERS: Transport covers are guaranteed free of defects in material or
workmanship at purchase. Covers are not guaranteed against rips, holes, or damage due to
improper installation, abuse, misuse, alteration, or environmental factors beyond our control.
RETURN POLICY
All returns must be made within 30 days from the date of purchase unless due to defect. Written
authorization MUST be obtained from WheelChair Carrier, Inc. prior to the return of any
merchandise for any reason, and all transportation costs must be prepaid. NO RETURNS on
custom orders. Authorized returns for credit only are subject to a 25% restocking charge, plus
any cost incurred in restoring the merchandise to a resalable condition. Freight charges cannot
be credited.
WHEELCHAIR CARRIER, INC.
7325 Douglas Rd.
Lambertville, MI 48144
PHONE: [phone] or call toll free at 1-800-541-3213
FAX: [phone]
www.WheelChairCarrier.com