Whelen Engineering Company SA315 User manual

Page 1
©2007 Whelen Engineering Company Inc.
Form No.14123A (050708) For warranty information regarding this product, visit www.whelen.com/warranty
Automotive: Sirens/Switches
Installation Guide:
SA315 Speaker Bracket
2002 Trailblazer
®
ENGINEERING COMPANY INC.
Internet: www.whelen.com
Sales e-mail: [email protected]
Customer Service e-mail: [email protected]
51 Winthrop Road,
Chester, Connecticut 06412-0684
Phone: [phone]
Installation:
1. Secure the speaker to
the bracket using the
supplied mounting
hardware (see next
page).
2. On the lower radiator
support, find the existing
holes shown in Figure 1.
Using the supplied
mounting hardware,
mount the bracket (with
speaker attached) to the
lower radiator support as shown in Figure 2.
3. Installation is complete and the speaker is ready to connect to power. Extend
the WHITE (Positive) and BLACK (Negative) speaker wires to your siren
amplifier and connect as shown in the amplifiers instructions.
NOTE: The bracket can be mounted to either side of the vehicle. Mounting is
identical, except the bracket will face the opposite way.
FRAME RAIL
MOUNTING
HOLES
SIREN
Fig. 1 Fig. 2 Passenger Side
RADIATOR
SUPPORT
FRONT TIRE
CAUTION
Loud siren noise can cause
hearing damage and/or loss.
Refer to OSHA Section 1910.95 prior
to putting ANY siren into service!
Wear
Protection!
ACTIVATION OF THIS
SIREN MAY DAMAGE
UNPROTECTED EARS!
©2007 Whelen Engineering Company Inc.
Form No.14123A (050708) For warranty information regarding this product, visit www.whelen.com/warranty
Automotive: Sirens/Switches
Installation Guide:
SA315 Speaker Bracket
2002 Trailblazer
®
ENGINEERING COMPANY INC.
Internet: www.whelen.com
Sales e-mail: [email protected]
Customer Service e-mail: [email protected]
51 Winthrop Road,
Chester, Connecticut 06412-0684
Phone: [phone]
Installation:
1. Secure the speaker to
the bracket using the
supplied mounting
hardware (see next
page).
2. On the lower radiator
support, find the existing
holes shown in Figure 1.
Using the supplied
mounting hardware,
mount the bracket (with
speaker attached) to the
lower radiator support as shown in Figure 2.
3. Installation is complete and the speaker is ready to connect to power. Extend
the WHITE (Positive) and BLACK (Negative) speaker wires to your siren
amplifier and connect as shown in the amplifiers instructions.
NOTE: The bracket can be mounted to either side of the vehicle. Mounting is
identical, except the bracket will face the opposite way.
FRAME RAIL
MOUNTING
HOLES
SIREN
Fig. 1 Fig. 2 Passenger Side
RADIATOR
SUPPORT
FRONT TIRE
CAUTION
Loud siren noise can cause
hearing damage and/or loss.
Refer to OSHA Section 1910.95 prior
to putting ANY siren into service!
Wear
Protection!
ACTIVATION OF THIS
SIREN MAY DAMAGE
UNPROTECTED EARS!

Page 2
1/4
(Speaker & Bracket)
-20X1-1/2"
HEX HEAD SS
1/4" SPLIT
LOCK
WASHER
1/4" SPLIT
LOCK
WASHER
1/4X20X1-1/4
HEX HEAD
(Speaker Only)
1/4
(Speaker & Bracket)
-20X1-1/2"
HEX HEAD SS
1/4" SPLIT
LOCK
WASHER
1/4" SPLIT
LOCK
WASHER
1/4X20X1-1/4
HEX HEAD
(Speaker Only)
SA315 / Rear View
wire
exit &
drain
hole
A
A
A A
IMPORTANT! It is the responsibility of the installation technician to make sure that the installation and
operation of this product will not interfere with or compromise the operation or efficiency of any vehicle
equipment!
IMPORTANT! Before returning the vehicle to active service, visually confirm the proper operation of this product, as well as all vehicle
components/equipment.
The SA315 siren speaker mounting kit comes with 3 long bolts (1/4-20 X 1-1/2” Hex Head SS). The
longer bolts are necessary to go through the mounting bracket, the siren housing and into the
siren driver. They will replace 3 of the 4 shorter bolts (“A”) that secure the siren driver to the
speaker housing. Your speaker is shipped with 2 of the shorter bolts installed. A short bolt
must be used in the 2 holes that do not go through the bracket so they will properly secure the
driver to the housing. If you need to remove all 4 bolts at once be sure to hold the driver
securely in place.
IMPORTANT: For drainage purposes, the speaker must be oriented so that the wire
passage hole is in the “6 o’clock” position (closest to the road).This is also the
drain hole for the siren. Improper mounting will result in premature driver failure
and void the product warranty.
SA315 / Rear View
wire
exit &
drain
hole
A
A
A A
IMPORTANT! It is the responsibility of the installation technician to make sure that the installation and
operation of this product will not interfere with or compromise the operation or efficiency of any vehicle
equipment!
IMPORTANT! Before returning the vehicle to active service, visually confirm the proper operation of this product, as well as all vehicle
components/equipment.
The SA315 siren speaker mounting kit comes with 3 long bolts (1/4-20 X 1-1/2” Hex Head SS). The
longer bolts are necessary to go through the mounting bracket, the siren housing and into the
siren driver. They will replace 3 of the 4 shorter bolts (“A”) that secure the siren driver to the
speaker housing. Your speaker is shipped with 2 of the shorter bolts installed. A short bolt
must be used in the 2 holes that do not go through the bracket so they will properly secure the
driver to the housing. If you need to remove all 4 bolts at once be sure to hold the driver
securely in place.
IMPORTANT: For drainage purposes, the speaker must be oriented so that the wire
passage hole is in the “6 o’clock” position (closest to the road).This is also the
drain hole for the siren. Improper mounting will result in premature driver failure
and void the product warranty.
IMPORTANT! It is the responsibility of the installation technician to make sure that the installation and operation of this product will not
interfere with or compromise the operation or efficiency of any vehicle equipment! Before returning the vehicle to active service,
visually confirm the proper operation of this product, as well as all vehicle components and equipment.
IMPORTANT! It is the responsibility of the installation technician to make sure that the installation and operation of this product will not
interfere with or compromise the operation or efficiency of any vehicle equipment! Before returning the vehicle to active service,
visually confirm the proper operation of this product, as well as all vehicle components and equipment.
DANGER! Sirens produces extremely loud emergency warning tones! Exposure to these tones without proper and adequate hearing
protection, could cause ear damage and/or hearing loss! The Occupational Safety & Health Administration (www.osha.gov) provides
information necessary to determine safe exposure times in Occupational Noise Exposure Section 1910.95. Until you have determined the safe
exposure times for your specific application, operators and anyone else in the immediate vicinity should be required to wear an approved
hearing protection device. FAILURE TO FOLLOW THIS RECOMMENDATION COULD CAUSE HEARING LOSS!
DANGER! Sirens produces extremely loud emergency warning tones! Exposure to these tones without proper and adequate hearing
protection, could cause ear damage and/or hearing loss! The Occupational Safety & Health Administration (www.osha.gov) provides
information necessary to determine safe exposure times in Occupational Noise Exposure Section 1910.95. Until you have determined the safe
exposure times for your specific application, operators and anyone else in the immediate vicinity should be required to wear an approved
hearing protection device. FAILURE TO FOLLOW THIS RECOMMENDATION COULD CAUSE HEARING LOSS!