Whirlpool LG6811XS User manual

\ I
i
Gas Model
LG6811XS
ashers. Clolhes Dryers, Freezers. RelrlgeralwFreezer Ice Makers Dishwashers. Built-In Ovens and Surlace Un~ls. Ranges, Microwave Ovens. Trash Comgacll

Parts and features
CYCLE CONTROL KNOB
RMATION CENTER
RE SELECTOR
START BUllON
Remove the Con-
sumer Buy Guide label
LINT SCREEN
before using your
dryer. It will be easier
DRYER DRUM
to remove.
Wipe out the dryer
drum with a damp
NUMBER PLATE
cloth to remove dust
from storing or ship-
ADING DOOR
ping.
Copy your Model and Serial Numbers here
When you need service or call with a
question, have this information ready:
1. Complete Model and Serial Numbers
Model Number
(from plate located as shown).
2. Purchase date from sales slip.
Serial Number
Copy this information in these spaces.
Keep this book in the Laundry Information
Purchase Date
Center with your “Dryer Guide” and sales
slip.
Thank you for purchasing a Whirlpool Service ComPany Phone Number
product. Please complete and mail the Owner Registration Card fur-
nished with this product.
Contents
Page Page
PARTS AND FEATURES 2 Gentle Heat. 7
IMPORTANT SAFETY Drying Times 8
INSTRUCTIONS, 3 Mixed Loads 8
OPERATING INSTRUCTIONS. 4 End-of-Cycle Signal 8
Selecting a Cycle and LINT SCREEN 9
Starting Your Dryer 4 LINT REMOVAL., 9
Automatic Cycles. 6 CARING FOR YOUR DRYER.. 10
Timed Drying 6 Cleaning Dryer Interior. 10
DRYING TIPS 7 Vacation Care 10
FLUFFAIR Setting 7 IF YOU NEED SERVICE OR
TUMBLE PRESS@Setting 7 ASSISTANCE 11
Automatic DRY-MISER” WHIRLPOOL DRYER
Control 7 WARRANTY 12
2 01987 Whirlpool Corporation

Additional Safety Instructions and Your Responsibilities
NEVER operate the dryer if... ALWAYS shut off the gas valve before leav-
l it ISnot working right [i.e. norsy. too hot]. ing on vacation.
l it is damaged. ALWAYS unplug the power supply cord or
l parts are missing [i.e. door latch). turn off electrical power before attempting
l all panels are not in place. to service the dryer. Shut off GAS VALVE if
l the lint screen is loose, damaged or yours is a gas dryer.
missing.
FOR YOUR SAFETY
If you smell gas:
1. Open windows.
2. Don’t touch electrical
switches.
3. FatFeguish any open
.
4. Immediately call your
gas supplier.
You are personally responsible for making
sure that your dryer...
l is properly maintained.
l is properly Installed and leveled in a well
ventilated room* on a floor that can sup-
port the weight.
l is located in an area where the tempera-
ture is above 45 F (7.2 C).
l is connected to the proper outlet and
electrical supply.’
l is properly connected to fuel and ex-
haust systems.’
l is not installed against drapes or
curtains.’
I
FOR YOUR SAFETY
l is used only for jobs normally expected
of home clothes drvers.
. is not used bv children or anyone unable
to operate it.properly.
*See “Installation Instructions” for com-
plete intormation.

TYPE OF LOAD
COTTONS - LINENS
EXTRA HEAVY - Bedspreads,
mattress pads, quilts
HEAVYWEIGHT FABRICS - Towels,
jeans, corduroys, work clothes
MEDIUMWEIGHT COTTONS -
Sheets, pillowcases, cotton
underwear, diapers
LIGHTWEIGHT COTTONS - Batistes,
organdies, lingerie
PERMANENT PRESS, SYNTHETICS
AND BLENDS
SUGGESTED SUGGESTED
CYCLE TEMPERATURE
HEAVY
HIGH
AUTOMATIC
REGULAR PERM’T PRESS
MED
KNITS GENTLE
LOW
HEAVYWEIGHT FABRICS - Work clothes,
jacket&raincoats .___.__._.___.,_._,._
MEDIUMWEIGHT FABRICS - Shirts, play AUTOMATIC
clothes, sheets, slacks. PERMANENT
LIGHTWEIGHT FABRICS - Lingerie, PRESS
blousesdresses .__.._._......_........
PERMIT PRESS
MED
MED LOW
KNITS
HEAVYWEIGHT - Cottons, rayons,
blends, T-shirts, slacks, shirts
LIGHTWEIGHT - Synthetics [polyester,
acrylic, etc.) and blends, lingerie,
blouses, dresses
LIGHTWEIGHT AND DELICATE FABRICS
Sheer Curtains (2 or 3 panels)
Gauze, lace, etc.
RUBBER, PLASTIC, HEAT-SENSITIVE
FABRICS
AUTOMATIC MED LOW
PERMANENT
PRESS KNITS GENTLE
LOW
AUTOMATIC
PERMANENT EX LOW
PRESS
FOAM RUBBER- Pillows, bras,
stuffedtoys............................
PLASTIC - Shower curtains,
tablecloths............................
RUBBER-BACKED RUGS
OLEFIN. POLYPROPYLENE. SHEERNYLON
FLUFF
AIR EX LOW

I
. Select a CYCLE
Turn the Control Knob either way to
point to the cycle and setting you
want. See page 6 for information on
the cycles.
3 . Push the START Button
The dryer will start tumbling when you
push the STARTButton.
Ifthe STARTButton is pushed when the
Cycle Control Knob is pointing to an
OFF area, the End-of-Cycle Signal will
sound. Dryer will not start.
2
Set
. TEMPERATURE SELECTOR
The Temperature Selector can be set
on any desired temperature or any-
where between 2 temperatures.
To stop and restart
the dryer
TOStop the dryer, open the door (or
furn the Control Knob to OFF).
TO r&art the dryer, close the door,
select Cycle, if necessary, and push
START.
The Cycle Control Knob should point to an OFF area when the dryer is
not in use. If the dryer is stopped before the cycle is finished, turn the Cycle
Control Knob to an OFF area. 5

II’
The automatic cycles
The automatic Cycles allow you to se-
lect the degree of dryness you prefer
for the clothes being dried.
The Control Knob will not move until
the clothes load is almost dry, or the
COOL-DOWN portion of the cycle has
been reached. Affer COOL-DOWN, the For the first few loads, set the Control
knob automatically moves to an OFF Knob to point to an * in either auto-
area and tumbling stops. matic cycle. When the dryer stops, feel
the dried items. 4
weight cotton items. The load tumbles
wlthout heat during the last 5 min-
utes. This helps make the load easier
to handle.
l If items are drier than you like, use
a setting to the right of the * the next
time YOU dry a similar load.
AUTOMATIC
PERMANENT
PRESSto dry
permanent
press, knits and other synthetic fab-
rics. The load tumbles without heat
during the last IO minutes. This helps
keep wrinkles from setting in, and
makes the load easier to handle.
l If items are not as dry as you like, use
a setting to the lett of the * the next
time you dry a similar load.
Timed drying
Use the TIMED DRYING Cycle for
any load you want to dry by time. For
example: small loads, large bulky
items, items to be fluffed or dusted
with the FLUFFAIR heat setting.
l Turn the Control Knob to the number
of minutes you want - from 10 to 70.
l The last 5 minutes of this cycle are
without heat - a cool-down time.
This helps make the load easier to
6 handle.

I I I
Drying tips
The dryer does not heat when the
Temperature Selector is set on FLUFF
AIR. This setting can be used to fluff
bedding, plastic tablecloths, foam
rubber pillows, stuffed toys, sneakers,
etc.
1. Turn the Control Knob to the number
of minutes you want in FLUFFAIR.
2. Push the STARTButton.
Automatic DRY-MISER”
Control
The thermostat senses the air
temperature. The dryer automatically
shuts off when the selected dryness
is reached.
TUMBLE PRESS” Setting
The TU6tBLE PRES
wrinkles from dry clothing such as
items that may have been packed
in a suitcase, closet, or items not
removed from the dryer.
1. Set Control Knob to TUMBLE PRESS.
2. Set Temperature Selector to PERMIT
PRESVMED.
3. Push STARTButton.
The load will tumble in heated air
for 15 minutes. The heat shuts off and
the dryer continues to tumble the load
for 5 more minutes. I
For best results, TUMBLE PRESSonly a
few items at a time. Put them on hang-
ers or fold them as soon as the dryer
stops.
Gentle Heat
The dryer automatically reduces
the heat settings in HEAVY HIGH and
PERMIT PRESSMED cycles. During
the last few minutes of each of
these cycles the dryer temperature
gradually reduces to a lower heat
setting. This helps prevent
overdrying.

I
Ii
Drying times Mixed loads
Drying times will vary depending on:
l amount of moisture in the clothes.
l type and weight of the fabric.
l size of the load.
l room temperature around the dryer.
l temperature of the wash rlnse water.
l amount of lint in the lint screen.
l dryer temperature selection.
See in your “Dryer Guide” for
more information.
When drying a load with different
kinds and weights of fabrics, use the
cycle suggested for the lightest fab-
rics. When the dryer stops, remove dry
items and reset the control.
End-of-cycle signal
The dryer sounds a signal to let you know when
the cycle is finished. The signal cannot be turned
off and is not adjustable.
The signal is helpful when you are drying per-
manent press, synthetics and other items that
should be taken out as soon as the dryer stops.

’ Lint screen
Clean the lint screen before each load. A screen blocked by lint can
increase drying time and may be a FIREHAZARD.
-5gz.zg+
R”.d+, -0: j
Open the lid and pull the lint screen
straight out. ROLL the lint off the screen with
your fingers. I
DO NOT rinse or wash the screen.
Push the screen firmly back into place.
Lint removal
Lint can gather inside the dryer and create a FIRE HAZARD. This lint should
be removed at least every 2 to 3 years, or more otten,
depending on dryer usage.
ELECTRIC DRYERS GAS DRYERS
Cleaning should be done only by a qualified person.
1. Remove back panel (electric)
or lower access panel (gas].
2. Avoid damaging wires,
thermostats, funnel or igniter,
3. Remove lint from shaded area -
see art-with a soft brush or
vacuum cleaner.
4. Replace panel; reconnect and
re-level dryer. 9

Remove lo& and sharp objects
from pockets and cuffs before drying -
pins, buckles, etc. Close metal
zippers.
Wipe off all spills with a damp, soft
cloth. Spills allowed to remain may
dull or damage the finish.
Never leave wet or damp laundry
in your dryer.
Sharp or heavy objects should
never be put on or in the dryer.
Check pockets for bolts, nuts etc
10
Some pretreatment products can
damage dials, consoles and finish.
Do not use these products on or near
your dryer.
Cleaning dry& interior
Garments which contain unstable
dyes, such as denim blue jeans or
brightly colored cotton Items, may
discolor the dryer interior. If the
interior is discolored, clean with
one of the following methods to
avoid staining later load items.
Powdered laundry detergent and
very warm water
Make a paste with detergent and
very warm water. Apply paste to
a soft cloth and scrub area until
all excess dye is removed. Wipe
thoroughly with a damp cloth.
Tumble a load of rags. -OR-
liquid spray household cleaner
Spray on stained area. Rub with
a cloth until all excess dye is
removed. Tumble a load of rags.
Vacation care
l Unplug power cord or turn off
electrical power.
l For gas dryers, close gas valve.
l Clean lint screen

If you need service or assistance,
we suggest you follow these five steps:
1. Before calling for
assistance...
Performance problems often result
from little things you can find and fix your-
self without tools of any kind.
IF YOUR DRYER DOES NOT RUN:
l Is the power supply plugged into a live
circuit with the proper voltage?
9 Is the door closed tightly?
l Did you push the START Button?
l Have you checked your home’s main
fuses or circuit breaker box?
IF YOUR DRYER DOES NOT HEAT:
l The AIR setting is without heat.
l The last minutes of heat settings are with-
out heat.
l Is the gas turned on? If not, turn the Con-
trol Knob to OFF. Turn on gas. Wait 5 min-
utes. Reset controls and start.
l An electric dryer uses a crrcuit breaker
or 2 fuses. If one fuse is blown, the dryer
may run, but not heat.
IF DRYING TIME SEEMS TOO LONG:
l Is the lint screen clean? See page 9 of
this book for cleaning instructions.
. See page of this book and your “Dryer
Guide”
2. If you need
assistance?..
Call Whlrlpool COOL-LINE ’ service as-
rlstance telephone number. Dlal tree
tram anywhere In the U.S.:
1-800-253-1301
and talk with one of our trained Consul-
tants. The Consultant can instruct you in
how to obtain satisfactory operation from
your appliance or, if service is necessary,
recommend a qualified service com-
pany in your area.
3. If you need service?..
Whirlpool has a
nationwide net-
work of franchised
TECH-CARE” Serv-
ice Companies
- FR*NC?!sE~!!!‘C! J TECH-CARE service
technicians are trained to fulfill the prod-
uct warranty and provide after-warranty
service, anywhere in the United States. TO
locate TECH-CARE service in your area,
call our COOL-LINE service assistance
telephone number (see Step 21 or look in
your telephone directory Yellow Pages
under:
Call our COOL-LINE service assistance
telephone number [see Step 2) and talk
with one ot our Consultants. or it you pre-
fer, write to:
Mr. Robert Stanley
Division Vice President
Whirlpool Corporation
2000 M-63
Benton Harbor, Ml 49022
5. If you need FSP’>
replacement parts?.
FSP IS a registered trademark of
Whirlpool Corporation for quality parts.
Look for this symbol of quality whenever
you need a replacement part for your
Whirlpool appliance. FSP replacement
parts will fit right and work right, because
they are made to the same exacting
specifications used to build every new
Whirlpool appliance.
*If you must call or write, please provide.
model number, serial number, date of
purchase, and a complete description
of the problem. This information is
needed in order to better respond to
your request for assistance.

WHIRLPOOL* DRYER
WARRANTY
DROOl
r
I-
D. Damage to dryer caused by accident, misuse, fire, flood, acts
of God or use of products not approved by Whirlpool.
WHIRLPOOL CORPORATION SHALL NOT BELIABLE FOR INCIDENTAL OR CONSE-
QUENTIAL DAMAGES. Some states do not allow the exclusion or limitation of
incidental or consequential damages so this limitation or exclusion may
not apply to you. This warranty gives you specific legal rights, and you may
also have other rights which vary from state to state.
Outside the United States, a different warranty may apply. For details, please
contact your franchised Whirlpool distributor or military exchange.
LENGTH OF WARRANN
FULL ONE-YEAR
WARRANTY
From Date of Purchase
WHIRLPOOL WILL PAY FOR
FSP@replacement parts and repair labor to
correct defects in materials or workmanship.
Service must be provided by a franchised
TECH-CARE s service company.
WHIRLPOOL WILL NOT PAY FOR
A. Service calls to:
1. Correct the installation of the dryer.
2. Instruct you how to use the dryer.
3. Replace house fuses or correct house wiring or plumbing.
4. Replace light bulbs.
6. Repairs when dryer is used in other than normal, single-family
household use.
C. Pick up and delivery. This product is designed to be repaired in
the home.
Part No. 3390209
01987 Whirlpool Corporation Printed in U.S.A.
e Makers. Dishwashers. Built-In Ovens and Surlace Units, Ranges. Microwave Ovens, Trash Compactors Room Air Conditioners Dehumidifiers Automatic W