Whirlpool  LER3622PQ User guide

®Electric Compact Dryer
PRODUCT MODEL NUMBERS OVERALL DIMENSIONS
RECESSED AREA AND CLOSET INSTALLATION
EXHAUST VENTING
LER3622P
Electrical: A four-wire or three-wire, single
phase, 120/240-volt, 60-Hz, AC-only, electrical
supply (or 120/208-volt electrical supply, if
specified on the serial/rating plate) is required on a
separate 30-amp circuit, fused on both sides of the
line. A time-delay fuse or circuit breaker is
recommended.
Exhaust venting: Exhaust your dryer to the
outside. Four-inch diameter vent is required. Rigid
or flexible metal exhaust vent must be used. Do
Not use plastic or metal foil vent. Exhaust outlet
hood must be at least 12 inches from the ground
or any object that may be in the path of the
exhaust.
Because Whirlpool Corporation policy includes a continuous commitment to improve
our products, we reserve the right to change materials and specifications without notice.
Dimensions are for planning purposes only. For complete details, see Installation
Instructions packed with product. Specifications subject to change without notice.
Ref. 8577196
08-24-05
23 78
(60.6 cm)
"
20 34
(52.7 cm)
"
31"†
(78.7 cm)
*
Recessed or closet installation - Dryer only
*Additional spacing recommended
Recessed or closet installation - Stacked
A. Side view - closet or confined area
B. Recessed area A. Recessed area
B. Side view - closet or confined area
C. Closet door with vents
AB
3"
(7.6cm)
14"
(35.6cm)
18" (45.7cm)
0"*
(0cm)
0"*
(0cm)
DRYER
WASHER
(7.6 cm)
3"
(30.5 cm)
12"
(30.5 cm)
12"
0"*
(0 cm)
0"*
(0 cm)
AB
C
1"
(2.5 cm)
3"
(7.6 cm
)
48 in.2
(309.7 cm )
2
24 in.
2
(154.8 cm )
2
3"
(7.6 cm)
Vent system chart
Number of
90º turns
or elbows
Type of
vent
Box or
louvered
hoods
Angled
hoods
0 Rigid metal
Flexible metal
36 ft (11 m)
28 ft (8.5 m)
26 ft (7.9 m)
22 ft (6.7 m)
1 Rigid metal
Flexible metal
26 ft (7.9 m)
18 ft (5.5 m)
16 ft (4.9 m)
12 ft (3.7 m)
2 Rigid metal
Flexible metal
16 ft (4.9 m)
8 ft (2.8 m)
6 ft (1.8 m)
2 ft (0.6 m)
Closet confined area
For closet installation
with a door, minimum
ventilation openings
in the top and bottom
of the door are
required. Louvered
doors with equivalent
ventilation openings
are acceptable.
*Most installations require a
minimum 5¹⁄₂" (14.0 cm)
clearance behind the dryer for
the exhaust vent with elbows.
Select the route that will provide the straightest and most direct path
outdoors. Plan the installation to use the fewest number of elbows and turns.
Use the fewest 90° turns possible.
Do not use vent runs longer than specified in vent length chart.
Determine the number of elbows you will need.
A. Louvered hood style
B. Box hood style
4"
(10.2 cm)
4"
(10.2 cm)
A
B
4"
(10.2 cm)
2.5"
(6.4 cm)
Recommended hood styles Angled hood style
is acceptable.