Whirlpool AWO 3751 User manual

GB AWO 3751 PROGRAMME CHART
❉: optional / Yes : dosing required
1) For improved garmentcare spin speed is restricted to 1000 rpm in this programme.
2) In this programme default spin speed can be increased till 400 rpm. 5019 301 05698
Whirlpool is a registered trademark of Whirlpool USA
Programme Care
Labels Type of wash/Notes Max Load Detergents and additives Special options Max
Spin
Speed
rpm
Softener Main
Wash Pre- wash Easy Ironing Eco Prewash Intensive Rinse Rinse Hold Variable Spin
Kg
Cotton
95°,60°,40°
Normally to heavily soiled bed linen, table linen and underwear, towels, shirts etc. made
of cotton, coloured cotton and linen.
For temperature selection, please respect the manufacturer's recommendation on the
care label.
With heavily soiled laundry the additional “Prewash” option can be selected as well.
5.5 ❉Yes ❉❉❉❉ ❉ ❉ ❉1450
Synthetics
60°,40°
Normally soiled blouses, shirts, overalls etc. made of polyester (Diolen, Trevira),
polyamide (Perlon, Nylon) or blends with cotton. 2.5 ❉Yes ❉❉❉❉ ❉ ❉❉1) 1000 1)
Daily load 40° Slightly to normally soiled textiles made of cotton and/or synthetics. 3.0 ❉Yes — ❉—— ❉❉❉1450
Quick Wash Shortly worn outer clothing made of cotton, polyester, polyamide and blends with
cotton. 3.0 ❉Yes — ❉—— ❉❉❉1450
Delicates
40°,30° Curtains and delicate clothing, dresses skirts, shirts and blouses. 1.5 ❉Yes ❉—— ❉—❉❉1) 1000 1)
Wool 30°, Cold Onlywoollenswithafelt-freefinish,labelledwiththewoolmarkandidentifiedasmachine washable.
If you select “Rinse Hold” do not leave items to soak for too long. 1.0 ❉Yes — — — — — ❉❉1) 1000 1)
Handwash Textiles made of linen, silk, wool and viscose marked as “handwashable”.
If you select “Rinse Hold” do not leave items to soak for too long. A very gentle spin is used in
this programme. 1.0 ❉Yes — — — — — ❉❉2) 400 2)
Rinse & Spin — Same as the last rinse and the final spin in the “Cotton” programme. 5.5 ❉——❉—— ❉❉❉1450
Spin — In this programme spinning is intensive. Same as the spin cycle in the “Cotton” programme. 5.5 —————— —— ❉1450
Gentle spin — In this programme spinning is gentle. Same as the spin cycle in the “Wool” programme. 1.5 —————— ——❉1) 1000 1)
Drain — Drain only - no spinning. Alternative method of terminating programme after “Rinse Hold”. — —————— ——— —
6th Sense intelligent technology always guarantees perfect results with maximum efficiency whatever
the wash load.
This washing machine is equipped with
automaticsafetyfunctionswhichdetectand
diagnose faults at an early stage and react
appropriately, e.g.:
A. “Water Tap Closed” indication
B. “Clean Pump” indication
C. “Door Locked” indication
D. Programme selector knob
E. Programme sequence indication
F. “Start/Pause” button
G. “Start/Pause” indication
H. “Remaining Time” display
I. “Reset” button
J. “Spin Speed” button
Selectingany optionthe indicationlightsup.
When the combination of programme,
additional options and temperature is not
possible, the indication lights switch off
automatically. Unsuitable combinations of
options are deselected automatically.
B
G
E
F
AC
HIJD
30105698GB.fm Page 1 Tuesday, January 25, 2005 9:52 AM
Black process 45.0° 100.0 LPI

5019 301 05698
Whirlpool is a registered trademark of Whirlpool USA
Add the detergent as described in the programme
table or in the chapter “Detergents and Additives”
in the booklet.
1. Turn the programme selector knob to the
desired programme and temperature.
2. The remaining time display shows the duration
of the chosen programme (in hours and
minutes) and after taking some seconds for
calculating,theindicationofthe“Start/Pause”
button is flashing.
3. The programme sequence and the predefined
spin speed indication corresponding to the
selected programme lights up.
Selecting any option the indication lights up.
When the combination of programme, additional
options and temperature is not possible, the
indication lights switch off automatically. Unsuitable
combinations of options are deselected
automatically.
“Easy Ironing” button
• Can be used together with “Cotton”,
“Synthetics” and “Daily” programmes to make
ironing easier.
• Increases the water quantity and the clothes are
spun very soft.
“Eco” button
• The duration of the wash is extended and the
temperature reduced to save up to 40% of
energy but maintaining good washing results.
“Prewash” button
• Only for heavily soiled loads (for example sand,
granular dirt) sensible. The cycle time increases
approximately 15 min.
“Intensive Rinse” button
• More water and a longer time in rinse cycle is
added.
• This option is particularly suitable for areas with
very soft water, washing baby linen and helps
people with allergies.
“Rinse Hold” button
• The laundry remains in the last rinse water
without progressing to the final spin cycle to
avoid creasing and prevent colours from
changing.
CONSUMPTION DATA
Programme Temperature
(°C)
Load
(kg)
Water
(l)
Energy
(kWh)
Approx.
Programme
Duration
(hours : minutes)*
Cotton 95 5.5 54** 1.90 2:00
Cotton 60 5.5 49 1.04 2:20
Cotton 40 5.0 44 0.60 2:05
Synthetics 60 2.5 55 0.80 1:30
Synthetics 40 2.5 55 0.60 1:20
Daily 40 3.0 45 0.50 1:00
Quick wash 30 3.0 37 0.40 0:30
Delicates 40 1.5 60 0.60 0:45
Wool 30 1.0 60 0.30 0:40
Handwash 30 1.0 45 0.30 0:40
Prewash cycle might increase programme duration. Consumption values were measured in normalized conditions in compliance
with Standard IEC 60 456. Consumption data in the home may vary with respect to the values in the table in relation to the
water supply pressure and temperature, the load and the type of wash.
* The remaining time indicator can similarly deviate from the values in the table, because it takes into account the household
conditions applicable at that time.
** To reduce the water temperature, some cold water is added at the end of the main wash cycle, before the pump drains the
water out.
ADD DETERGENTS, CLOSE THE DOOR
AND SELECT THE PROGRAMME
SELECT ANY DESIRED OPTION
• This option is particularly recommended for the
programme “Synthetics”, “Daily” and
“Delicates”.
• This function is particularly useful if you want to
postpone spinning to a later time, or if you want
to drain only.
Note: The programme stops to “Rinse Hold” at
thetimethe“RinseHold”light intheprogramme
sequence indication is on.
Terminate the “Rinse Hold” option:
• Press the “Rinse Hold” button again; the
programmewillterminateautomaticallywith the
final spin cycle for the present wash programme.
• If you do not wish to spin the clothes, turn the
programme selector knob counterclockwise to
the “Drain” programme and press the
“Start/Pause”buttonagain whenthe indication
next to it is flashing.
“Spin Speed” button
• Every programme has an automatic predefined
maximum spin speed.
• Press the button to set another spin speed.
• If the spin speed “0” is selected, the final spinning
is cancelled but intermediate spin peaks remain
during rinse. The water is drained out only.
Open the tap and pressthe “Start/Pause” button.
The indication next to the “Start/Pause” button
lights up. The indications show the sequence
reached in the programme. After starting the
programme, the sequence indication runs from left
to right through Wash, Rinse, Spin.
When the sequence of the programme is finished
the corresponding indication goes out.
“Water Tap Closed”
The appliance has no or insufficient water supply.
Open the water tap; if the indication still lights up,
refer to the “Troubleshooting Guide” in the
Instructions for Use.
“Clean Pump”
Wastewaterisnotpumpedout.Checkwhetherthe
drain hose is kinked or the filter must be cleaned; in
the latter case refer to the Instructions for Use
(“Removing the Filter”).
“Door Locked”
As long as a washing programme is running, the
lamp lights up to show that the door cannot be
opened. When the indication goes off, the door can
be opened again.
• The remaining time is on “0:00” and all the lights
of the programme sequence indication are off.
1. Turn the programme selector to the “Off/0”
position.
2. Close the water tap.
3. Open the door and unload the machine.
4. Leave the door ajar to allow the drum to dry out.
1. Press the “Start/Pause” button to pause the
programme. The light flashes.
2. Selectthenewprogramme(withtemperature),
any options and another spin speed if you want.
3. Press the“Start/Pause” buttonagain. Thenew
programme continues at the same position
wherethepreviousprogrammewasinterrupted.
Do not add detergent for this programme.
The “Reset” button cancels a programme before
the end.
• Press the “Reset” button for at least 3
seconds. Any existing water is drained out
before the door can be opened.
PROGRAMME START
RED INDICATIONS
PROGRAMME END
CHANGE THE PROGRAMME, OPTIONS
AFTER PROGRAMME START
CANCEL (RESET) A RUNNING
PROGRAMME BEFORE THE END
30105698GB.fm Page 2 Tuesday, January 25, 2005 9:52 AM
Black process 45.0° 100.0 LPI

5019 301 05698
Whirlpool is a registered trademark of Whirlpool USA
If you wish to connect
hot and cold water
supply (Fig.1):
1. Fix the red marked inlet hose at the hot
water tap and at the inlet valve with the red
filter on the rear side of machine.
2. Fix the otherinlet hose at the cold water tap
and at the inlet valve with the blue filter on
the rear side of the machine.
Make sure:
a) The connections are tightly fixed
b) Do not invert their position
(for example: cold fill into hot inlet valve and
viceversa).
If you wish to connect only the
cold fill follow the below
instruction (Fig.2):
1. You need a Y-piece connector. The
Y-piece connector can be ordered via our
Service Organization or purchased in a
specialized hydraulic component store.
2. Fix the Y-piece connector to the cold fill
tap.
3. Connect the two inlet valves present on
therear part of the machine to the Y-piece
connector using the relative provider
hoses.
Make sure:
All connections are tightly fixed.
HOT / COLD FILL INSTRUCTION
Fig.1 Fig.2
Do not allow children to operate, crawl on, near or inside your
washer.
Note that during wash cycles, the surface temperature of the
porthole door may increase.
Close supervision of children is necessary when the appliance is
used near children.
30105698GB.fm Page 3 Tuesday, January 25, 2005 9:52 AM
Black process 45.0° 100.0 LPI