Whirlpool FWMD10502G Series Installation guide

Health & safety guide

50

650-1200 mm
inlet hose
inlet hose
inlet hose
inlet hose
inlet hose

Consumer should follow the softener
instructions.
Follow the dosage recommendation. It optimizes the cleaning result, it avoids
irritating residues of surplus detergent in your laundry and it saves money by avoiding
waste of surplus detergent.

CONTROL PANEL
Interactive knob can be rotated , pressed and display functions. The display
panel can show programmes , time remaining, parameters, options, status of
operation, etc.
Rotate the knob to choose desired wash programmes, press the knob to start;
when a programme is running, the knob will has a function of 'start/pause'.
when the machine is in standby, long press the knob for 3 seconds will
initiate the Auto start programme.
PROGRAMME AREA
When power on, the default programme is “Mixed", rotate the knob to
choose desired programme, and the chosen programme will be lighted,
other programmes' light will dim.
When a programme has been running consecutively for more than 3 times,
then the programme will become default when power on the next time.
Rotate to choose, press to select/ start
Additional functions
for current programme
( lit on means set )
Remaining time & animation
for current programme
Key parameters for current
programme(Wash temperature,
Rinse times, Spin speed)
Child lock indicator
Door lock indicator
Knob diagram
For best result, do not exceed max kg laundry.
5. QUICK STAIN option
6. HYBRID option
Programme area
special detergents and do not exceed maximum kg
declaration of laundry for this programme.
requires
5. 6.
AIR REFRESH
This programme refreshes garments by removing
bad odours and relaxing the fibres for easy ironing.
When choosing this programme, you cannot
change the temperature, speed and rinse times.
Hybrid indicator
and oxycare
“
“

RAPID
Enables quicker washing. The cycle duration is
reduced based on the programme selected.
DELAY
STAIN
Power on, rotate the knob to select the right
programme, then press 'Stain' button to enables stain
wash function. This function helps to remove all kinds
of stains for daily clothes (for selected programmes).
Pre-treatment is recommended for stubborn stains.
When set stain function successfully, the icon of
is lit.
QUICK STAIN
Power on, rotate the knob to select the right
programme, then press“QUICK STAIN” button to
select stain types, which includes red wine, oil stain,
makeup stain. This function is to treat specific stain
quicker for daily clothes.
When set special stain function successfully, the icon
of “ ”is lit, and the icon of corresponding stain is lit
too.
Stain type Introduction of special stain function.
To treat wine stain on daily clothes.
To treat oil stain on daily clothes.
To treat makeup stain on daily clothes.
The appliances adjust the average washing temperature to
ensure the wash programme is specifically adapted to each
type of stain. This ensures stains are treated in the best
possible way.
Note:
RINSE+SPIN
BEDDING
For washing big items like home textile.
When choosing this programme, you can change the temperature, speed and rinse times.
Used to rinse and spin the load.
When choosing this programme, you can
change the speed and rinse times.
For washing normally soiled cotton garments. At
60°C , this is the standard cotton programme and
the most efficient in terms of water and energy
consumption.
When choosing this programme, you can change
the speed.
By selecting this option, the efficiency of the
rinse is increased and optimal detergent
removal is guaranteed.
It is particularly useful for sensitive skin.
Power on, select a programme and desired
functions, press “Delay” button to set an appointment
time.
Steps to set Delay time
1.Press “Delay” button, the time will be changed in
order;
2. Long press “Delay” button, the time will be
changed continuously;
3. After setting delay time, press knob or press
'Start/Pause' button to start delay function.
4. Press power button to exit delay phase.
5. The maximum Delay time is 24H, the set delay
time is the finish time.
6. The ending time may differ when setting delay
due to the difference of water pressure, load,
water temperature and so on.
When delay function successfully, the icon of
is lit.
TEMP
temperature.
temperature
TEMP
Red wine
Oil stain
Makeup
stain

Suggestion tip: Selecting Hybrid steam will invoice ozone + steam operation, is composite function, Ensure water tap is
turned on.
HYBRID STEAM
Select desired programme, and press "HYBRID"button to choose between Ozone + steam,Ozone only,or
Steam only.
Press "Start/ Pause" button or press knob to start programme.
Mode For compatible wash programmes For air refresh programme
Ozone +
steam
Steam and ozone work during the operation to care and sterilize clothes. When
selecting this option, there will be an ozone operation phase followed by steam to
block proliferation of unpleasant odours caused by bacteria. After the operations,
the machine will generates steam periodically and perform slow drum rotations to
prevent crease formed. This option cycle starts at the end of washing programme
and continue for maximum 6 hours; it can be interrupt at any time by pressing
'Start/pause' button or press the knob. Wait for few seconds before opening the door.
Steam and ozone work during the operation to care
and sterilize clothes. When selecting this option, there
will be an ozone operation phase followed by steam to
block proliferation of unpleasant odours caused by
bacteria. During the steam phase, the machine will
perform slow drum rotations to prevent crease formed.
For this option, there is no 6 hours steam operation.
Ozone works during the operation to sterilize clothes, the drum will rotate but
there is no 6 hours steam.
Ozone works during the operation to sterilize clothes.
In this mode, the drum will not rotate and there is no 6
hours steam.
Ozone
steam When selecting this option, the appliances generates steam to block proliferation of
unpleasant odours caused by bacteria. During the steam phase, the machine will
perform slow drum rotations to prevent crease formed. This option cycle starts at
the end of washing programme and continue for maximum 6 hours; it can be
interrupt at any time by pressing 'Start/pause' button or press the knob. Wait for few
seconds before opening the door.
+
prevent
TEMP
To save energy, the washer will be automatically
switch off approximately 10 mins after
programme end.
Press this button once to pause it
after programme has started. To continue, press
again to resume the operation.
As long as a wash programme is running, the
door remains locked. To open the door while a
programme is in progress, press the
“Start/Pause” button. Provided the water level
and/or temperature is/are not too high , you
can open the door. For example to add/ remove
laundry.
Press the “Start/Pause” button again to continue
the programme.
Forcing the door to open may cause parts
damage or injury.
The mode selected will be lit. For ozone + steam mode, the icon of HYBRID is lit.
AUTO START
Long press 3s the knob will activate Auto Start
programme from shutdown mode. The max.
wash load is 7kg. You can only adjust speed and
rinse times.
Not recommended for wool or silk garments.
Steam works during the operation to care and refresh
clothes. In this mode, the drum will rotate but there is
no 6 hours steam.

ADJUSTABLE PARAMETERS
When running a programme, you can still change some settings without the need to pause or restart the
programme.
Parameters that can be adjusted are rinse times, spin speed and add Hybrid option.
You can only change the parameters before start of the operation.
POWER SAVING FUNCTION
2 minutes after the machine has started (non-pause),
the control panel will enter into power saving
function. Touch any button except power button to
wake up the UI.
P
T
S R
R
M
PRSHQ
S
: Compatible options to add on to wash programmes
kg
rpm kg
3:50
fornormally
soiled clothes

must
frequently will
will step by step
increase
“TEMP”
“TEMP”
“TEMP”
“TEMP”
“SPEED”
“RINSE”
“SPEED”
“SPEED”
“SPEED”
“RINSE”
“RINSE”
“RINSE”
cycle
Press "Rapid" for quicker washing, The cycle duration is
reduced based on programme selected.
(optional)
M

“DELAY”
(press "ON/OFF" button, after
confirming that the machine is powered on, long press
"Start/Pause" button, when you hear the prompt tone
for the second time, the buzzer prompt is canceled.)

Hybrid
Stain
When the hybrid function is set.
1. When the quick stain function is .set
2. When the stain function is .set
This indicator will light up:
When auto start cycle is running.
Auto start

Thewashingdryermachinemaysometimesnotworkproperlyforcertainreasons.BeforecallingtheSupportCentre,itis
recommendedtochecktoseeiftheproblemcanbeeasilyresolvedusingthefollowinglist.
Anomalies Possiblecauses/Solution
Thewasherdoes
notturnon.
• The plug is not inserted into the electrical outlet, or not enough to make contact.
• There has been a power failure. Press the ON/OFF button to reset programme.
• The door is not fully closed.
Thewashcycledoes
notstart.
• The ON/OFF button has not been pressed.
• The START/PAUSE button has not been pressed.
• The water tap is not open.
• A start delay has been set.
Thewasherdoes
notfillwithwater.
• The water intake hose is not connected to the tap.
• The hose is bent.
• The water tap is not open.
• The mains water supply has been shut off.
• There is not enough pressure.
Thewasherloads
anddrainswater
continuously.
• The START/PAUSE button has not been pressed.
• The drain hose has not been installed at 120 cm from the ground.
• The end of the drain hose is immersed in water.
• The drain connector on the wall does not have an air vent.
Iftheproblempersistsafterhavingperformedthesechecks,closethewatertap,shutoffthewasher
dryer,andcalltheSupportCentre.Ifthedwellingislocatedononeoftheuppermostfloorsofa
building,asiphoneffectcansometimesoccur,thuscausingthewashertoloadanddrainwater
continuously.Specialanti-siphonvalvesareavailableonthemarkettopreventthesetypesof
problems.
Thewasherdoes
notdrainordoesnot
spin.
• The programme does not include the draining function: with certain programmes it must be activated
manually.
• The drain hose is bent.
• The drain line is obstructed.
Thewasher
vibratesexcessively
duringthespincycle
• At the time of installation, the drum was not properly unlocked.
• The washer is not level.
• The washer is squeezed between furniture and the wall.
Thewasherleaks
water.
• The water intake hose has not been tightened properly. Please check your hose regularly and in
caseofanydamageorleakagehaveitreplaced.
• The detergent dispenser is clogged.
• The drain hose has not been properly fastened.
Thedisplayshowsan
errorcode.
• Shut off the machine, disconnect the plug from the outlet, and wait about 1 minute before turning it
backon.Iftheproblempersists,calltheSupportCentre.
Toomuchfoamis
formed.
• The detergent is not compatible with the washer (it must bear the wording “for washing
machines”,“forhandwashingandwashingmachines”,orsomethingsimilar).
• The dosage was excessive.
Abnormalsoundduring
spin
• The power cord or other objects touch the cabinet.
• Transport bolts have not been removed.
• Foreign objects such as coins or hairpins are in the drum.

“ON/OFF”
“
”