Whirlpool AWO D5306 User manual

CONTENTS
BEFORE USING THE WASHING MACHINE
PRECAUTIONS AND GENERAL
RECOMMENDATIONS
DESCRIPTION OF THE WASHING MACHINE
DOOR
CHILD SAFETY (IF AVAILABLE)
BEFORE THE FIRST WASH CYCLE
PREPARATION OF THE WASHING
DETERGENTS AND ADDITIVES
REMOVING THE FILTER
DRAINING RESIDUAL WATER
CARE AND MAINTENANCE
TROUBLESHOOTING GUIDE
AFTER-SALES SERVICE
ACCESSORIES
TRANSPORT / HANDLING
ELECTRICAL CONNECTION

19
BEFORE USING THE WASHING MACHINE
1.Removing the packaging and inspection
•After unpacking, make sure that the washing
machineisundamaged.Ifindoubt,donotusethe
washing machine. Contact After-Sales Service or
your local retailer.
•Checkthattheaccessoriesandsuppliedpartsare
all present.
•Keep the packaging materials (plastic bags,
polystyrene parts, etc.) out of reach of children,
as they are potentially dangerous.
2.Remove the transport bolts
•The washing machine is fitted with transport
boltstoavoidanypossibledamagetotheinterior
during transport. Before using the machine, it is
imperative that the transport bolts are removed.
•After their removal, cover the openings with the
4 enclosed plastic caps.
3.Install the washing machine
•Remove the protective film from the control panel.
•Movethe appliancewithoutliftingitbytheworktop.
•Install the appliance on a solid and level floor
surface, preferably in a corner of the room.
•Make sure that all four feet are stable and resting
on the floor and then check that the washing
machine is perfectly level (use a spirit level).
4.Water inlet
•Connect the water supply inlet hose in
accordance with the regulations of your local
water company.
•Water inlet: Cold water only
(if no other information on
your programme chart)
•Water tap: 3/4” threaded hose
connector
•Water pressure
(flow pressure): 100-1000 kPa (1-10 bar).
•Only use a new inlet hose for connecting the
washing machine to the water supply. Used
hoses must not be employed anymore
5.Drain
•Connect the drain hose to the siphon or hook it
over the edge ofa sink by means ofthe “U” bend
supplied.
•If the washing machine is connected to an
integrated drainage system, ensure the latter is
equipped with a vent to avoid simultaneous
loading and draining of water (siphoning effect).
6.Electrical connection
•Electrical connections must be carried out by a
qualified technician in compliance with the
manufacturer’sinstructionsandcurrentstandard
safety regulations.
•Data regarding voltage, power consumption and
protection requirements is given on the inside of
the door.
•Theappliancemustbeconnectedtothemainsby
means of a socket with an earth connection in
accordance with current regulations. The
washing machine must be earthed by law. The
manufacturer declines all liability for damage to
property or injury to persons or animals due to
non-compliance with the directions given above.
•Do not use extension leads or multiple sockets.
•Before any maintenance on the washing machine
disconnect it from the mains supply.
•After installation, access to the mains plug or to
disconnection from mains supply must be
ensured at all times via a double-pole switch.
•Do not operate the washing machine if it has
been damaged during transport. Inform the
After-Sales Service.
•Mainscable replacementis onlytobe carriedout
by After-Sales Service.
•The appliance must only be used in the
household for the prescribed uses.
Minimum housing dimensions:
Width: 600 mm
Height: 850 mm
Depth: 600 mm

20
PRECAUTIONS AND GENERAL
RECOMMENDATIONS
1.Packaging
•Thepackagingmaterialis entirelyrecyclable,and
marked with the recycling symbol . Adhere
to current local regulations when disposing of
packaging material.
2.Disposing of packaging and scrapping
old washing machines
•The washing machine is built from reusable
materials. It must be disposed of in compliance
with current local waste disposal regulations.
•Before scrapping, remove all detergent residues
and cut off the power cable so that the washing
machine is made unusable.
•This appliance is marked according to the
European directive 2002/96/EC on Waste
Electrical and Electronic Equipment (WEEE).
By ensuring this product is disposed of correctly,
you will help prevent potential negative
consequences for the environment and human
health, which could otherwise be caused by
inappropriate waste handling of this product.
The symbol on the product, or on the
documents accompanying the product, indicates
that this appliance may not be treated as
household waste. Instead itshall be handed over
totheapplicablecollectionpointfortherecycling
of electrical and electronic equipment.
Disposal must be carried out in accordance with
local environmental regulations for wastedisposal.
For more detailed information about treatment,
recovery and recycling of this product, please
contact your local city office, your household
waste disposal service or the shop where you
purchased the product.
3.Location and surroundings
•The washing machine must only be installed in
closed spaces.
•Do notstoreflammable fluids near the appliance.
4.General recommendations
•Do not leave the appliance plugged in when not
in use.
•Turn off the tap.
•Before any cleaning and maintenance switch off
the machine or disconnect it from the mains.
•Clean the outside of the washing machine with a
damp cloth. Do not use abrasive detergents.
•Never open the door forcibly or use it as a step.
•Children must not be allowed to play with the
washing machine or to climb into the drum (see
also the following page chapter “Child Safety”).
•If necessary, the power cable may be replaced
with an identical one obtained from our After-
Sales Service. The power cable must only be
replaced by a qualified technician.
5.EC Declaration of Conformity
•The appliance conforms to the following
European Standards:
73/23/EEC Low voltage directive
89/336/EEC Electromagnetic Compatibility
Directive
93/68/EC CE Marking Directive .

21
DESCRIPTION OF THE WASHING MACHINE
DOOR
CHILD SAFETY (IF AVAILABLE)
BEFORE THE FIRST WASH CYCLE
1. Worktop
2. Control panel
3. Detergent dispenser
4. Service plate
(inside the door)
5. Door
6. Child safety device (if provided,
inside the door)
7. Plinth covering pump access
8. Adjustable feet
To open the door, hold the door handle, press the inside handle and pull the door. Close the door by pressing
it without excessive force until it clicks shut.
Toprotecttheapplianceagainstimproperuse,turntheplastic
screw on the interior of the door. To do this, use the thick
rounded corner of the coloured insert from the detergent
dispenser or a coin:
•Slot vertical: the door will not lock.
•Slot horizontal - normal position: the door can be locked
again.
To remove any residual water used in testing by the manufacturer, we recommend that you carry out a short
wash cycle without laundry.
1. Open the tap.
2. Close the door.
3. Pour a little detergent (about 30 ml) into the main wash chamber of the detergent dispenser.
4. Select and start a short programme (see separate quick reference guide).
1
2
4
5
6
3
7
8

22
PREPARATION OF THE WASHING
1.Sort the laundry according to...
• Type of fabric / care label symbol
Cottons, mixed fibres, easy care/synthetics, wool,
handwash items.
• Colour
Separate coloured and white items. Wash new
coloured articles separately.
•Loading
Wash items of different sizes in the same load to
improvewashingefficiencyanddistributioninthedrum.
• Delicates
Wash small items (e.g. nylon stockings, belts etc.)
and items with hooks (e.g. bras) in a cloth bag or
pillowcase with zip.Always removecurtain ringsor
wash curtains with the rings inside a cotton bag.
2.Empty all pockets
Coins, safety pins etc. can damage your laundry as
well as the appliance drum and tub.
3.Fasteners
Close zips and fasten buttons or hooks; loose belts
or ribbons should be tied together.
Stain removal
•Blood, milk, eggs etc. are generally removed by the
automatic enzyme phase of the programme.
•To remove red wine, coffee, tea, grass and fruit
stains etc. add a stain remover to the main wash
chamber of the detergent dispenser.
•Pre-treat heavily-soiled areas with stain remover if
necessary.
Dyeing
•Only use dyes that are suitable for washing machines.
•Follow the Manufacturer’s instructions.
•Plasticandrubberpartsof the washingmachinecan
be stained by dyes.
Loading the laundry
1.Open the door.
2.Load the articles one at a time loosely into the
drum, without overfilling. Observe the load sizes
given in the quick reference guide.
Note: overloading the machine will result in
unsatisfactory washing results and creased laundry
3.Close the door.
DETERGENTS AND ADDITIVES
The choice of detergent depends on:
•typeoffabric(cottons,easycare/synthetics,delicate
items, wool).
Note: Use only specific detergents for washing wool
•colour
•the wash temperature
•degree and type of soiling
Remarks:
Any whitish residues on dark fabrics are caused by
insoluble compounds used in modern phosphate-free
powder detergents. If this occurs, shake or brush out
the fabric or use liquid detergents.
Use only detergents and additives specifically
produced for domestic washing machines.
When using descaling agents, dyes or bleaches for the
pre-wash, make sure that they are suitable for use in
domestic washing machines. Descalers could contain
products which could damage your washing machine.
Do not use any solvents (e.g. turpentine, benzine). Do
not machine wash fabrics that have been treated with
solvents or flammable liquids.
Dosage
Followthedosagerecommendationsonthedetergent
pack. They depend on:
•degree and type of soiling
•size of wash
followthedetergentmanufacturer’sinstructionsfor
a full load;
half load: 3/4 the amount used for a full load;
Minimum load (about 1 kg):
1/2 the amount used for a full load
•water hardness in your area (ask for information
fromyourwatercompany).Softwaterrequiresless
detergent than hard water (refer to the water
hardness table in the operating instructions).
Notes:
Too much detergent can result in excess foam
formation, which reduces washing efficiency.
If the washing machine detects too much foam, it may
prevent spinning.
Insufficient detergent may result in greylaundry in time
and also calcifies the heating system, drum and hoses.
Water Hardness Chart
Water hardness Characteristics German
°dH French °fH English °eH
1
2
3
4
soft
average
hard
very hard
0-7
7-14
14-21
over 21
0-12
12-25
25-37
over 37
0-9
9-17
17-26
over 26

23
Where to put detergent and additives
The detergent drawer has three chambers (fig. “A”).
Prewash Chamber
•Detergent for the prewash
Main Wash Chamber
•Detergent for the main wash
•Stain remover
•Water softener (water hardness class 4)
Softener Chamber
•Fabric softener
•Liquid starch
Pour additives only up to the “MAX” mark.
Using chlorine bleach
•Washyourlaundryin the desiredprogramme (Cotton, Synthetics),
addinganappropriateamountofchlorinebleachtotheSOFTENER
chamber (close the detergent dispenser carefully).
•Immediately after end of programme, start the “Rinse and Spin”
programme to eliminate any residual bleach smell; if you want,
you can add softener.
Never put both chlorine bleach and softener into the softener
chamber at the same time.
How to position the separator in the main wash
chamber for powder or liquid detergent
For use with powder detergent: place the separator in the higher
position.
Lift the separator until its top can be reclined. Place its hooks on the
upper end of the back guide rails and slightly push the separator
down to fix it (fig. “B” and “C”).
Agapshouldremainbetweentheseparatorandthebottomofthemain
washchamber,iftheseparatorhasbeencorrectlyinstalled(fig.“B”and
“C”).
Forusewithliquiddetergent:placetheseparatorinthelowerposition.
Secure the separator in the chamberusing the front guide rails.
Position the separator so that it touches the bottom of the main
wash chamber (fig. “D”).
A
A
()
Separator
B
Hooks
Separator
Guide
Rails
C
1
2
3
1
D

24
Notes:
•Keep detergents and additives in a safe, dry place out of the reach of children.
•Liquid detergents can be used for programmes with prewash. However, in this case a powder
detergent must be used for the main wash.
•Do not use liquid detergents when activating the “Start Delay” function (if available on your washing
machine).
•Topreventdispensingproblemswhenusinghighlyconcentratedpowderandliquiddetergents,usethe
special detergent ball or bag supplied with the detergent and place it directly inside the drum.
•When using descaling agents, bleaches or dyes, make sure that they aresuitable for washing machines.
Descalers could contain components that can damage parts of your washing machine.
•Do not use any solvents in the washing machine (e.g. turpentine, benzine).
•If you use starch powder, proceed as follows:
1. Wash your laundry using the desired wash programme.
2. Prepare the starch solution according to the starch manufacturer’s instructions.
3. Select the “Rinse and Spin” programme, reduce the speed to 800 rpm and start the programme.
4. Pull out the detergent drawer until you can see about 3 cm of the main wash chamber .
5. Pour the starch solution into the main wash chamber while the water is running into the
detergent drawer.
6. Iftherearestarchresiduesin thedetergentdrawerwhentheprogrammehasfinished,cleanthemain
wash chamber.

25
REMOVING THE FILTER
DRAINING RESIDUAL WATER
We recommend that you check and clean the filter
regularly, at least two or three times a year.
Especially:
•If the appliance is not draining properly or if it fails to
perform spin cycles.
•If the pump is blocked by a foreign body (e.g. buttons,
coins or safety pins).
IMPORTANT: make sure the water has cooled
before draining the appliance.
1. Stop the appliance and unplug it.
2. Remove the plinth by holding it tight on both sides,
pushing it downward and tilting it to the front.
3. Place a container beneath it.
4. Open the filter but do not remove it completely.
Slowly turn the filter counterclockwise until the water
begins to drain out.
5. Wait until all the water has drained.
6. Now unscrew the filter completely and remove it.
7. Clean the filter and the filter chamber.
8. Check that the pump rotor moves freely.
9. Re-insert the filter and screw it in clockwise as far as it
will go.
10.Pour about 1 litre of water into the detergent drawer
to reactivate the “Eco system”. Check that the filter is
inserted properly and securely.
11.Reinstall the plinth.
12.Plug in the appliance once again.
13.Select a programme and start it.
Before emptying the residual water, switch the appliance off and unplug it from the mains socket.
Remove the plinth. Place a container beneath it.
1. Open the filter but do not remove it completely. Slowly turn the filter counterclockwise until the
water begins to drain out.
2. Wait until all the water has drained.
3. Now unscrew the filter completely and remove it.
4. Tilt the appliance forwards carefully to allow the water to flow out.
5. Re-insert the filter and screw it in clockwise as far as it will go.
6. Reinstall the plinth.
Before using the washing machine again:
1. Pour approx. 1 litre of water into the detergent drawer to reactivate the “Eco system”.
2. Plug in the appliance once again.

26
CARE AND MAINTENANCE
Appliance exterior and control panel
•Can be washed down with a soft, damp cloth.
•A little neutral detergent (non abrasive) can also
be used.
•Dry with a soft cloth.
Door seal
•Clean with a damp cloth when necessary.
•Check the condition of thedoor seal periodically.
Filter
•Check and clean the filter regularly, at least two
or three times a year (see “Removing the filter”).
Do not use flammable fluids for cleaning the appliance.
Detergent dispenser
1. Press the release lever in the main wash compartment
downward and remove the drawer (fig. “A”).
2. Remove the cover grid from the fabric softener compartment.
Remove the separator from the main wash compartment by
pulling it upward (fig. “B”).
3. Wash all the parts under running water.
4. Refit the separator and the grid in the detergent drawer and fit
the drawer back inside its housing. A
B

27
Water supply hose
Check the supply hose regularly for brittleness and cracks and
replace it if necessary using a new hose of the same type (available
from After-Sales Service or specialist dealer).
If your supply hose has a transparent hose coating (fig. “C”),
periodically check the colour of the transparent coating. If the
coating begins to turn red, this is an indication that the hose may
have a leak and should be replaced. Contact our After-Sales Service
team or specialist dealer to obtain a replacement hose.
Mesh filter for water connection
Check and clean regularly.
For washingmachines with an inlet hose as shown on pictures “A”,
“B” or “C” (depending on the model):
1. Close the tap and loosen the inlet hose on the tap.
2. Cleantheinternalmeshfilterandscrewthewaterinlethoseback
onto the tap.
3. Now unscrew the inlet hose on the rear of the washing machine.
4. Pull off the mesh filter from the washing machine connection
with universal pliers and clean it.
5. Refit the mesh filter and screw the inlet hose on again.
6. Turn on the tap and ensure that the connections are completely
water-tight.
A
B
C