Whirlpool LA7900XS User manual

AUTOMATIC
WASHER
Super Capacity
Model
LA79ooxs
hcrowave Ovens. lrash Compactors, Room Au Condltloners. Oehumldlflers. Automatic Washers. Clothes Dryers. Freezers. Refrigerator-I

Contents
Page
PARTS AND FEATURES 2
IMPORTANT SAFETY
INSTRUCTIONS.. 3
OPERATING INSTRUCTIONS.. 4
Starting Your Washer 4
What Happens in Each
Cycle 6
OTHER OPERATING
INSTRUCTIONS.. 12
For a Rinse and Spin 12
Page
For a Drain and Spin 12
For a Soak 12
Liquid Bleach Dispenser 13
MAGIC CLEAN” Lint Filter 13
CARING FOR YOUR WASHER 14
Winterizing 15
IF YOU NEED SERVICE OR
ASSISTANCE 16
WASHER WARRANTY 20
I
01987 Whirlpool Corporation
Parts and features
LOAD LAUNDRY TEMPERATURE CYCLE MAGIC CLEAN@
CONTROL LINT FILTER
KNOB (not shown)
LIQUID BLEACH
DISPENSER
MODEL AND SERIAL
NUMBER PLATE
(not shown)
Remove the Consumer
Buy Guide label. It will be
easier to remove before the
washer is used.
You should wipe out the
basket with a damp cloth
before using to remove dust
from storing or shipping.
Copy your Model and Serial Numbers here
When you need service or call with a
question, have this information ready:
1. Complete Model and Serial Numbers Model Number
(from plate under the lid near the
hinge). Serial Number
2. Purchase date from sales slip.
Copy this information in these spaces. Purchase Date
Keep this book, your”Laundry Guide” and
sales slip in the Laundry Information Service Company
Center. Phone Number
Please complete and mall the Owner Registration Card furnished with
this product.
2

Additional Safety Instructions and Your Responsibilities
ALWAYS store detergent, laundry aids ALWAYS unplug the power supply
and other materials in a cool, dry cord before attempting to service the
place where children can’t reach washer.
them- in a locked cabinet if possible. DO NOT machine wash glass fiber
ALWAYS read and follow instructions materials. Small particles can stick to
on packages of detergent and laun- fabrics washed in following loads
dry aids - especially warnings and and cause skin irritation.
precautions. You are personally responsible for
HAZARDOUS FUMES can be formed if making sure that your washer:
chlorine bleach is used in the same
l is used only for jobs normally ex-
wash as ammonia or acids such as
vinegar or rust remover. petted of home automatic washers.
l is not run by children or anyone un-
able to operate it properly. 3

Operating instructions
Starting Your Washer
yI$ Be sure to measure and add detergent, then Place
a sorted load in the washer before starting it.
1 . Select a LOAD SIZE
l Turn the knob to point at a setting
that describes the size of load you
want to wash.
l Set the knob anywhere on or be-
tween EX SMALL [a few small items)
and EX LARGE (a full load).
l To change the water level after the
washer has started to fill, turn the knob
to RESET,then the desired water level.
I
NOTE: Use the EX LARGE water
level for best permanent press
results.
2
Select
. WATER TEMPERATURES
l Select wash and rinse water tem-
peratures by pushing a button.
l This drawing shows a warm wash
(top temperature) and cold rinse
(bottom temperature) selection.
Recommended wash temperatures
can be found in your “Laundry Guide.”
LOAD SIZES AND WATER LEVELS
For best cleaning results, the
load must be able to move freely
in the water. Too big a load or too
little water can cause wear or
CAUTION:
DO NOT
OVERLOAD WASHER.
EX LARGE (21.7 gaU82.1 L)’
MEDIUM (16.8 galJ63.6 L)’
EX SMALL (11.9gal./450 L)*
tearing of load items.
*Approximate
fill with load.

3. Start the washer
A. Push in the Control Knob and turn
it to the right. It must be pushed in
and turned only clockwise.
B. Stop on a number in the cycle
you want. The numbers are min-
utes of wash time. The drawing
shows 10 minutes of agitation in
the REGULAR NORMAL Cycle.
C. Start the washer by pulling out
the Control Knob. The washer will
fill to the level you set with wash
water of the selected temper-
ature. After filling, the washer will
agitate for the selected number
of minutes.
D. To stop the washer at any time,
push in the Control Knob. To
restart the washer, pull out the
Control Knob.

What Happens in Each CyFle*
Each cycle has different agitation and spin speeds designed for different
kinds of fabrics. Numbers on the dial in each cycle are the minutes of WASH
agitation time.
When the Cycle Control Knob is set to a number and pulled out, the washer fills
before aaitation and timina starts. After aaitation starts, the knob turns clock wise
until it points to OFF and thecycle ends, -
REGULAR HEAVY Cycle
A cycle for sturdily con-
structed fabrics that are
heavily soiled.
REGULAR NORMAL Cycle
A cycle for regular loads
of fabrics that are moder-
ately soiled.
PERMANENT PRESS NORMAL Cycle
PERMANENT
A cycle designed for mod-
erately soiled permanent
press and some synthetic
fabrics. The cool-down
rinse helps keep wrinkles
from setting into these
fabrics.
DRAIN
No
Agitation

NOTE: You may hear the sound of water spraying during the spin parts of some
cycles. In some cycles, cold water is sprayed on the spinning load to help with
the rinsing.
Genlie Wash System
For better fabric care in the REGULAR and PERMANENT PRESScycles, the
agitation speed is reduced during the last few minutes of wash time.
NOTE: Always use cold rinse water
for permanent press fabrics.

PERMANENT PRESS LIGHT Cycle
A cycle designed for
lightly soiled permanent
press and some synthetic
fabrics. The cool-down
rinse helps keep wrinkles
from setting into these
fabrics.
REFILL
q
COOL
DOWN
KNITS/GENTLE NORMAL Cycle
A cycle that gently
washes and spins moder-
ately soiled delicate items
and washable knits.
pauslng for a brief soak
perlod.
KNITS/GENTLE LIGHT Cycle
A cycle that gently
washes and spins lightly
soiled delicate items and
washable knits.
A Indicates the machlne is
pauslng for a brief soak
perlod.
8

NOTE: Always use cold rlnse water
for permanent press fabrics.

SOAK Cycle
detergent or pre-soak
additive. The SOAK Cycle
should always be fol-
lowed by a Wash Cycle.
SUPER WASH Cycle
Use for washing heavily
soiled loads that require
maximum soil removal.
Double the amount of
detergent recommended
when uslng the SUPER
WASH Cycle.
FILL
to
u
Selected
Level
WASH
4
Minutes
High
Speed
c
10

Special care is needed when soaking or pre-washing laundry.
See your “Laundry Guide” for proper use of this cycle.
REFILL
Selgted
Level
The washer will proceed to the
REGULAR/HEAVY Cycle. If you
want a different cycle to follow
SUPERWASH, push in the cycle
control knob, turn to the cycle ant
time you want, pull knob out to
start.

Other operating instructions
For a rinse and spin For a drain and spin
You may need an extra rinse and
spin for heavily soiled loads which
need more detergent. (Extra detergeni
can require an extra rinse.]
I. Push Control Knob in.
2. Turn clockwise to any l on the dial.
See above drawing.
3. Pull Control Knob out. The washer
will fill to selected level; agitate 2
minutes; drain and spin.
Your washer can be set to drain and
spin out water.
1. Push Control Knob in.
2. Turn clockwise to the bar just before
the OFF area in any cycle. See
above drawing.
3. Pull Control Knob out. The washer
will drain and spin.
For agitation and spin speeds in each cycle, see pages 6-11.
For a soak
for best results, use warm water
for soaking or pre-washing stained
laundry. Hot water can set stains.
shouldblways be followed by a
Wash Cycle.
Important: See additional care
lnformatlon In your “Laundry
Guide!’
‘To start soak with agitation, the Cycle Control Knob
must point to the number in the SOAK Cycle.
12

Liquid bleach dispenser
Always measure bleach. Do not
guess. Never use more than 1cup
(250 ml] for a full load. Use less with
lower water level settings. Follow
directions on bottle for safe use. Use
a cup with a pouring spout to avoid
spilling.
L
1.
2.
3.
Load the washer first.
Pour measured bleach carefully
into dispenser. DO NOT let bleach
splash, drip or run down into the
washer basket. Undiluted bleach
will damage any fabric it touches.
Start the washer. Bleach will be
diluted automatically during the
wash part of the cycle.
For more information on bleaching, see your “Laundry Guide!’
MAGIC CLEAN@ lint filter
The lint filter in your washer cleans itself. Collected
lint is drained away with the wash and rinse water.
If your washer drains into a tub, remove any lint
collected in the drain or strainer.

Caring for your washer
OF
WHEN NOT WASHING, keep both
water faucets turned off, this takes the
pressure off the water inlet valve and
hoses.
AFTER WASHING, use a soft dry cloth to
wipe the outside and inside dry. Leave
the lid up until the basket is dry. Wipe
up spills right away. Spills can dull or
damage the finish.
REMOVE SHARP OBJECTS such as
pins, buckles, etc., from clothes before
washing. Close metal zippers.
SHARP OR HEAVY OBJECTS should
never be put on or in the washer.
Check pocket for bolts, nuts, tools, etc.
SOME PRETREATMENT PRODUCTS can
damage washer and dryer dials, con-
soles and finishes. Do not use these
products on or near your washer or
dryer.
14

Winterizing
Because some water stays in the washer, freezing
can cause a lot of damage. If your washer is
stored or moved during the cold weather...
1. Shut off both water 2. Put a quart of R.V.
faucets. Disconnect or automobile type
and drain water antifreeze in the
inlet hoses. basket.
To use the washer again...
I. Flush water pipes and hoses.
2. Connect hoses to the washer
3. Turn on the water faucets.
3. Set the washer for a
DRAIN and SPIN
[see page 12). Let it
run for about 30
seconds to mix the
antifreeze and
water.
4. Run the washer
through a com-
plete cycle with
one cup of deter-
gent to clean out
the antifreeze.

If you need service or assistance,
we suggest you follow these five steps:
1. Before calling for
assistance...
Performance problems often result
from little things you can find and fix
yourself without tools of any kind.
If your washer does not fill:
l Is the power supply core
PUwd
,.:
*ri
into a live circuit with the proper
voltage?
l Have you checked your home’s
main fuses or circuit breaker box?
l Are the water supply hoses kinked?
l Is the Cycle Control Knob set and
pulled out?
If your washer does not spin:
l Is the lid closed?
l Is the power supply cord plugged
into a live circuit with the proper
voltage?
l Have you checked you home’s
main fuses or circuit breaker box?
If your washer fills and drains
wlthout running:
l Make sure that the Cycle Control
Knob is pointing to a number in the
cycle.
Make sure the drain hose is higher
than the water level in the washer.
If it Isn’t:
l The washer may seem to be drain-
ing during wash and rinse cycles.
l Water can siphon out. (See “lnstalla-
tion Instructions:‘)
l Are both water faucets open?
16

2. If you need
assistance%.
Call Whlrlpool COOL-LINE@ serv-
Ice assistance telephone number.
Dlal free from anywhere In the U.S.:
I-800-253-1301
and talk with one of our trained Con-
sultants. The Consultant can instruct
you in how to obtain satisfactory
operation from your appliance or, if
service is necessary, recommend a
qualified service company in your
area.
3. If you need service?..
Whirlpool has a
nationwide network
of franchised TECH-
CARE@ Service Com-
panies, TECH-CARE
service technicians
are trained to fulfill the product
warranty and provide after-warranty
service, anywhere in the United States.
To locate TECH-CARE service in your
area, call our CCCL-LINE service assis-
tance telephone number (see Step 2) or
look in your telephone directory Yellow
Pages under:
4. If you have a
problem? ..
Call our COOL-LINE service as-
sistance telephone number (see Step
2) and talk with one of our Consultants,
or if you prefer, write to:
Mr. Robert Stanley
Division Vice President
Whirlpool Corporation
2000 M-63
Benton Harbor, Ml 49022
5. If you need FSP”
replacement parts?..
FSP is a registered trademark of
Whirlpool Corporation for quality
parts. Look for this symbol of quality
whenever you need a replacement
partforyour Whirlpool appliance. FSP
replacement parts will fit right and
work right, because they are made to
the same exacting specifications
used to build every new Whirlpool
appliance.
‘If you must call or write, please pro-
vide: model number, serial number,
date of purchase, and a complete
description of the problem. This infor-
mation is needed in order to better
respond to your request for
assistance.

Notes
18

Notes
19

WHIRLPOOL” AUTOMATIC WASHER
WARRANTY
LENGTH OF WARRANTY
FULL ONE-YEAR
WARRANTY
From Date of Purchase
WHIRLPOOL WILL PAY FOR
FSP” replacement parts and repair laborto
correct defects in materrals or workmanship.
Service must be provided by a franchised
TECH-CARE” service company.
LIMITED FIVE-YEAR
WARRANTY
From Date of Purchase
FSPreplacement parts for any part of gear-
case assembly if defective in materials or
workmanship. The gearcase assembly is
shown below.
LIMITED TEN-YEAR FSPreplacement of outer tub should it crack,
WARRANTY or fail to contain water, due to defective
From Date of Purchase materials or workmanship.
WHIRLPOOL WILL NOT PAY FOR
A. Service calls to:
1. Correct the installation of the washer.
2. Instruct you how to use the washer.
3. Replace house fuses or correct house wiring or plumbing.
6. Repairs when washer is used in other than normal, single-family
household use.
C. Pick up and delivery. This product is designed to be repaired in
the home.
D. Damage to washer caused by accident, misuse, fire, flood, acts
of God or use of products not approved by Whirlpool.
E. Any labor costs during the limited warranties,
WHIRLPOOL CORPORATION SHALL NOT BELIABLE FOR INCIDENTAL OR CONSE-
QUENTIAL DAMAGES. Some states do not allow the exclusion or limitation of
incidental or consequential damages so this limitation or exclusion may
not apply to you. This warranty gives you specific legal rights, and you may
also have other rights which vary from state to state.
Outside the United States, a different warranty may apply. For details, please
contact your franchised Whirlpool distributor or military exchange.
GEARCASE ASSEMBLY
COVERED BY YOUR
WARRANTY
Part No. 3349145
01987 Whirlpool Corporation Printed in U.S.A.