Whirlpool AWO/D 049 User manual

GB AWO/D 049 PROGRAMME CHART
❉: optional / Yes : dosing required
1) For improved garment care, spin speed is restricted to 400 rpm in this programme. 5019 301 10448
Whirlpool is a registered trademark of Whirlpool USA
Programme Care
Labels
Type of wash/Notes
- for temperature selection, respect the manufacturer’s recommendations on the care label
Max
Load
kg
Detergents and additives Special options Spin
Speed
rpm
Pre-
wash Main Wash Softener Spin
speed
reduction
500 rpm
Rinse hold
Cotton with prewash
95 °C Heavily soiled, long wearing and temperature stable textiles in cotton and linen (bed linen, table
linen, underwear, shirts etc.). 5.0 Yes Yes ❉❉❉
1000
Cotton
40 - 60 - 95 °C
Normally to heavily soiled bed linen, table linen and underwear, towels, shirts etc. made of cotton
and linen. 5.0 — Yes ❉❉❉
1000
Synthetics with prewash
60 °C Heavily soiled blouses, shirts, overalls etc. made of polyester (Diolen, Trevira), polyamide (Perlon,
Nylon) or blends with cotton. 2.5 Yes Yes ❉❉❉
1000
Synthetics
30 - 40 - 60 °C
Normally soiled blouses, shirts, overalls etc. made of polyester (Diolen, Trevira), polyamide
(Perlon, Nylon) or blends with cotton. 2.5 — Yes ❉❉❉
1000
Delicates
30 °C Curtains and delicate clothing, dresses skirts, shirts and blouses. 1.5 — Yes ❉❉❉
1000
Quick wash
30 °C Shortly worn outer clothing made of cotton, polyester, polyamide and blends with cotton. 3.0 — Yes ❉❉❉
1000
Wool
Cold - 40 °C Only woollens with a felt-free finish, labelled with the woolmark and identified as machine
washable.
If you select “Rinse Hold” do not leave items to soak for too long. 1.0 — Yes ❉❉❉
1000
Handwash
30 - 40 °C Textiles made of linen, silk, wool and viscose marked as “handwashable”.
If you select “Rinse Hold” do not leave items to soak for too long. A very gentle spin is used in this
programme. 1.0 — Yes ❉—❉400 1)
Rinse & Spin — Same as the last rinse and the final spin in the “Cotton” programme. 5.0 — — ❉❉❉ 1000
Spin — In this programme spinning is intensive. Same as the spin cycle in the “Cotton” programme. 5.0 — — — ❉—1000
Gentle Spin — In this programme spinning is gentle. Same as the spin cycle in the “Wool” programme. 1.0 — — — ❉—1000
Drain — Drain only - no spinning. Alternative method of terminating programme after “Rinse Hold”. ——— — — — —
A. “Door open” indication
This washing machine is equipped with
automatic safety functions which
detect and diagnose faults at an early
stage and react appropriately, e.g.:
B. “Service” indication
C. “Water tap closed” indication
D. “Clean pump” indication
E. Programme selector
F. “Start/Pause” button
G. Programme sequence indicator
H. “Reset” button
D
G
C
FH
E
B
A

5019 301 10448
Whirlpool is a registered trademark of Whirlpool USA
Add detergent as indicated on the front page and as
described in your Instructions for Use. Close the
door and turn the programme selector to the
desiredprogrammeandtemperature.Theindication
lamp next to the “Start /Pause” button flashes.
Push the button(s) of any option(s) desired - the
respective indication lamp lights up.
When the combination of programme and additional
option(s)is notpossible, theindicationlights switchoff
automatically. Unsuitable combinations of options are
deselected automatically.
“Spin speed reduction 500 rpm” button
• Reduces the predetermined automatic maximum
spin speed to treat your laundry more gently.
“Rinse hold” button
• The laundry remains in the last rinse water
withoutprogressing to the finalspincycle to avoid
creasing and prevent colours from changing.
• This option is particularly recommended for the
programmes “Synthetics” and “Delicates”.
• This function is particularly useful if you want to
postpone spinning to a later time, or if you want
to drain only.
Note: The programme stops to “Rinse hold” at
the time the “Rinse hold” light in the programme
sequence indicator is on. The indication lamp
next to the “Start/Pause” button flashes.
Terminate the “Rinse hold” option:
• Press the “Start/Pause” button; the
programmewillterminateautomatically withthe
final spin cycle for the present wash programme.
• If you do not wish to spin the clothes, turn the
programme selector knob to the “Drain”
programme and press the “Start/Pause” button.
CONSUMPTION DATA
Programme Temperature
(°C)
Load
(kg)
Water
(l)
Energy
(kWh)
Approx. Programme
Duration
(hours : minutes)
Cotton 95 5.0 49** 1.90 2:00
Cotton*** 60 5.0 44 0.85 2:20
Cotton 40 5.0 44 0.60 2:00
Synthetics 60 2.5 50** 0.70 1:30
Synthetics 40 2.5 45 0.55 1:15
Quick wash 30 3.0 40 0.40 0:30
Delicate 30 1.5 50 0.50 0:45
Wool 40 1.0 55 0.60 0:45
Handwash 40 1.0 45 0.60 0:40
Handwash 30 1.0 45 0.50 0:40
Consumption values were measured in normalized conditions in compliance with Standard IEC/EN 60 456. Consumption
data in the home may vary with respect to the values in the table in relation to the water supply pressure and temperature,
the load and the type of wash.
** To reduce the water temperature, some cold water is added at the end of the main wash cycle, before the pump drains
the water out.
*** Reference Programme for Energy Label.
ADD DETERGENTS, CLOSE THE DOOR
AND SELECT THE PROGRAMME
SELECT ANY DESIRED OPTION
Open the tap and press the “Start/Pause” button.
The indication lamp next to the “Start/Pause”
buttonlights up. The programmesequence indicator
shows the current programme phase, running from
left to right through Wash, Rinse, Spin/Drain.
When the programme phase is finished, the
corresponding indication goes out.
Before starting and after end of a programme, the
lamplights to showthat the doorcan be opened.As
long as a wash programme is running, the door
remains locked and must on no account be forced
open. In case you have an urgent need to open it
during a running programme, refer to “Cancel
(Reset) a running programme before the end”.
“Service”
Lightingupof the“Service”indicationcanbe caused
by a fault in an electrical component. Refer to the
“Troubleshooting Guide” in your “Instructions for
Use”; if the fault persists, contact our After Sales
Service.
“Water tap closed”
The appliance has no or insufficient water supply.
Open the water tap; if the indication still lights up,
refer to the “Troubleshooting Guide” in the
Instructions for Use.
“Clean pump”
Wastewaterisnotpumpedout.Checkwhetherthe
drain hose is kinked or the filter must be cleaned; in
the latter case refer to the Instructions for Use
(“Removing the Filter”).
• All the lights of the programme sequence
indicator are off, and the “Door open”
indication lights up.
1. Turn the programme selector to the “Off/O”
position.
2. Close the water tap.
3. Open the door and unload the machine.
4. Leave the door ajar to allow the drum to dry.
1. Press the “Start/Pause” button to pause the
programme. The light flashes.
2. Selectthe newprogramme (withtemperature),
any options and another spin speed if you want.
3. Press the“Start/Pause” buttonagain. The new
programme continues at the same position
wherethepreviousprogrammewasinterrupted.
Do not add detergent for this programme.
The “Reset” button cancels a programme before
the end.
•Pressthe“Reset” button for at least 3
seconds. Any existing water is drained out
before the door can be opened.
PROGRAMME START
“DOOR OPEN” INDICATION
RED INDICATIONS
PROGRAMME END
CHANGE PROGRAMME AND/OR OPTIONS
AFTER PROGRAMME START
CANCEL (RESET) A RUNNING
PROGRAMME BEFORE THE END