Whirlpool Cabrio W10280477A User manual

cabr,o
FABRIC CARE SYSTEM
TOP-LOADING
HIGH EFFICIENCY
LOW-WATER WASHER
USE AND CARE GUIDE
LAVEUSE HAUTE
EFFICACITI_ A FAIBLE
CONSOMMATION D'EAU
AVEC CHARGEMENT
PAR LE DESSUS
GUIDE D'UTILISATION
ET D'ENTRETIEN
Para una version de estas instrucciones en espafiol, visite www.Whirlpool.com
Table of Contents Table des mati6res
WASHER SAFETY ......................................................... 2
WHAT'S NEW UNDER THE LiD? ................................. 3
CONTROL PANEL AND FEATURES ............................ 4
CYCLE GUIDE ............................................................... 5
USING YOUR WASHER ................................................ 6
Using Laundry Product Dispensers...............................7
Starting Your Washer ......................................................7
WASHER MAINTENANCE .................................................9
TROUBLESHOOTING .......................................................11
WARRANTY .........................................................................16
ASSISTANCE OR SERVICE .............................Back Cover
SECURIT#:: DE LA LAVEUSE ...................................... 17
QUOI DE NEUF SOUS LE COUVERCLE? ................ 18
TABLEAU DE COMMANDE
ET CARACT¢:RISTIQUES .......................................... 19
GUIDE DES PROGRAMMES ...................................... 21
UTILISATION DE LA LAVEUSE .................................. 23
Utilisationdes distributeurs de produits de lessive ..24
Mise en marche de la laveuse ..................................... 25
ENTRETIEN DE LA LAVEUSE .........................................27
D#PANNAGE .......................................................................29
GARANTIE ...........................................................................35
ASSISTANCE OU SERVICE .................Couverture arri_re
Designed to use only HE High Efficiency
detergents.
Con_ue pour I'utilisation d'un d6tergent haute
efficacit6 seulement.
W10280477A
W10280478A =SP

WASHER SAFETY
Your safety and the safety of others are very important.
We have provided many important safety messages in this manual and on your appliance. Always read and obey all
safety messages.
This is the safety alert symbol.
This symbol alerts you to potential hazards that can kill or hurt you and others.
All safety messages will follow the safety alert symbol and either the word "DANGER" or
"WARNING." These words mean:
You can be killed or seriously injured if you don't
immediately follow instructions.
You can be killed or seriously injured if you don't
follow instructions.
All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you
what can happen if the instructions are not followed.
IMPORTANT SAFETY INSTRUCTIONS
WARNING: To reduce the risk of fire, electric shock, or injury to persons when using the washer, follow basic precautions,
including the following:
[] Read all instructions before using the washer.
[] Do not wash articles that have been previously cleaned
in, washed in, soaked in, or spotted with gasoline,
dry=cleaning solvents, other flammable, or explosive
substances as they give off vapors that could ignite or
explode.
[] Do not add gasoline, dry=cleaning solvents, or other
flammable, or explosive substances to the wash water.
These substances give off vapors that could ignite or
explode.
[] Under certain conditions, hydrogen gas may be
produced in a hot water system that has not been used
for 2 weeks or more. HYDROGEN GAS IS
EXPLOSIVE. Ifthe hot water system has not been
used for such a period, before using the washing
machine, turn on all hot water faucets and let the water
flow from each for several minutes. This will release
any accumulated hydrogen gas. As the gas is
flammable, do not smoke or use an open flame during
[]
[]
Do not allow children to play on or in the washer. Close
supervision of children is necessary when the washer is used
near children.
Before the washer is removed from service or discarded,
remove the door or lid.
[] Do not reach intothe washer if the drum, tub or agitator is
moving.
[] Do not install or store the washer where itwill be exposed to
the weather.
[] Do not tamper with controls.
[] Do not repair or replace any part of the washer or attempt any
servicing unless specifically recommended in this manual or in
published user-repair instructions that you understand and
have the skills to carry out.
[] See "Electrical Requirements" for grounding instructions.
this time. SAVE THESE INSTRUCTIONS
State of California Proposition 65 Warnings:
WARNING: This product contains a chemical known to the State of California to cause cancer.
WARNING: This product contains a chemical known to the State of California to cause birth defects or other reproductive harm.
2

WHAT'S NEW UNDER THE LID?
Cleaning with Less
Traditional agitator-style
washing machine
Washplate
Washer with low-water
washplate wash system
The most striking difference in your new washer is the
low-water washplate wash system. The washer automatically
adjusts the water level to the load size--no water level selector
is needed.
As the washer dampens and moves the load, the level of the
clothes will settle in the basket. This is normal, and does not
indicate that more clothes should be added.
IMPORTANT: You will not see a washer basket full of water
as with your past agitator-style washer.
maximum load hek
When loading the washer with dirty laundry, fill it evenly
around the basket wall. For best results, fill no higher than the
recommended maximum load height.
Automatic Load Size Sensing
Once you start the cycle, the lid will lock, and the washer will
begin the sensing process to determine the correct water level
for the load. This may take several minutes. You will find a
step-by-step description in the "Cycle Status Lights" section.
Choosing the Right Detergent
Use only High Efficiency detergents. The package will be
marked "HE" or "High Efficiency." Low-water washing creates
excessive sudsing with a regular non-HE detergent. Using
regular detergent will likely result in longer cycle times and
reduced rinsing performance. It may also result in component
failures and noticeable mold or mildew. HE detergents are made
to produce the right amount of suds for the best performance.
Follow the manufacturer's instructions to determine the amount
of detergent to use.
Use only High Efficiency (HE) detergent.
Concentrated Cleaniag
Low-water cleaning means concentrated cleaning. Rather
than diluting detergent as done in an agitator-style washer,
this washer delivers the detergent directly to the soils.
The washplate moves the load while water is added in small
amounts until the load is wet. This low-water wash method
uses less water and energy compared to a traditional
agitator-style washer.
Normal Sounds You Can Expect
At different stages of the wash cycle, you may hear sounds and
noises that are different from those of your previous washer.
For example, you may hear a clicking and hum at the beginning
of the cycle, as the lid lock goes through a self-test. There
will be different kinds of humming and whirring sounds as the
washplate moves the load. And sometimes, you may hear
nothing at all, as the washer determines the correct water level
for your load or allows time for clothes to soak.
3

CONTROL P EL FEATURES
cQbrlo
POWER
Fabric
Softener
o I I
HEAvl l
IDUTY Hot Extra Heavy
START Warm Heavy igh
Pause/Unlock
with_ Cool Medium
Cold Light pin
DRAIN & SPIN L_J
C3
Sensing W_sh Spin Done LL°_k Extra Temp Soil Spin
Rinse Level Speed
I I
NORMAL
QUICKWASH
O WASH CYCLE KNOB
Use the Wash Cycle Knob to select available cycles on your
washer. Turn the knob to select a cycle for your laundry load.
See "Cycle Guide" for detailed descriptions of cycles.
CYCLE OPTIONS
When you select a cycle, its default settings will light up. Not
all cycles and options are available on all models.
TEMP
Temperature Control senses and maintains uniform water
temperatures by regulating incoming hot and cold water.
Select a wash temperature based on the type of fabric
and soils being washed. For best results and following
the garment label instructions, use the warmest wash
water safe for your fabric.
• Warm and hot water will be cooler than what your
previous washer provided.
• Even in a cool water wash, some warm water may
be added to the washer to maintain a minimum
temperature.
SOIL LEVEL
Soil level (wash time) is preset for each wash cycle.
For most loads, use the soil level that is preset with the
cycle you have chosen. For heavily soiled and sturdy
fabrics, press Soil Level to select more wash time,
if needed. For lightly soiled and delicate fabrics, press
Soil Level to select less wash time, if needed. Lower soil
level setting will help reduce tangling and wrinkling.
SPIN SPEED
This washer automatically selects the spin speed
based on the cycle selected. The preset speeds can be
changed. Not all spin speeds are available with all cycles.
• Faster spin speeds mean shorter dry times, but may
increase wrinkling in your load.
• Slower spin speeds mean less wrinkling, but will leave
your load more damp.
You may also add or remove options for each cycle. Note
that not all options can be used with all cycles, and some
are preset to work with certain cycles.
OEXTRA RINSE
This option can be used to automatically add a second
rinse to most cycles.
0FABRIC SOFTENER
This option must be selected if using fabric softener
during a cycle. It ensures that fabric softener is added
at the correct time in the rinse for even distribution.
4
OCYCLE STATUS LIGHTS INDICATOR
The Cycle Status Lights show the progress of a cycle. At each
stage of the process, you may notice sounds or pauses that
are different from traditional washers.
Sensing Wash Rinse Spin Done
SENSING Sensing Wash Rinse Spin Done
When the START/Pause/Unlock button is pressed, the
washer will first perform a self-test on the lid lock
mechanism. You will hear a click, the basket will make a
slight turn, then lid will unlock briefly before locking again.
Once the lid has locked the second time, the washer will
slowly spin the dry load to estimate the load size and
amount of water needed, and begin adding water. The
washer will then move the load briefly, pause to allow
water to soak into the load, and resume adding water. This
process may repeat until the correct amount of water has
been added for the load. You may also hear water flowing
through the dispenser, adding detergent to the load.
NOTE: The sensing light may also come on during the
Wash portion of the cycle. This is normal.
WASH Sensing Wash Rinse Spin Done
You will hear the washplate moving the load. Unlike
traditional washers, the load is not covered with water.
Low-water cleaning means concentrated cleaning. Rather
than diluting detergent as done in an agitator-style washer,
this washer delivers the detergent directly to the soils. The
motor sounds may change at different stages in the cycle.
The wash time is determined by the selected soil level.
RINSE Sensing Wash Rinse Spin Done
You will hear sounds similar to the wash cycle as the
washer rinses and moves the load. Fabric softener will
be added if the Fabric Softener option was selected.
SPIN Sensing Wash Rinse Spin Done
The washer spins the load at increasing speeds for proper
water removal, based on selected cycle and spin speed.
DONE Sensing Wash Rinse Spin Done
Once the cycle is complete, this light will come on.
Remove the load promptly for best results.

LID LOCK D
Lid
Lock
To allow for proper load sensing, the lid will lock and the
Lid Lock light will turn on. This light indicates that the lid
is locked and cannot be opened.
If you need to open the lid, press START/
Pause/Unlock. The lid will unlock once the
washer movement has stopped. This may
take several minutes if the load was spinning
at high speed. Press START/Pause/Unlock
again to resume the cycle.
C3
START
Pause/Unlock
CYCLE GUIDE
Settings and options shown in bold are default settings for that cycle. For best fabric care, choose the cycle that best fits the load
being washed.
Not all cycles and options are available on all models.
"Iterns tO
wash:
Machine-wash
silks, hand-
wash fabrics
Small loads,
cottons,
polyester,
perm press
Cottons, linens,
sheets, and
mixed garment
loads
Cottons, sheets,
and mixed
garment loads.
No-iron fabrics,
cottons, perm
press, linens,
synthetics
CYcle:
iii i i
Delicate
Quick
Wash
Normal
Eco
Normal
Casual
.I,,,. .
Wash!Rinse Spin Soil Available Cycle Detads:
Temperature: Speed: Level: Options: .................
Hot/Cold High Extra Heavy
Warm/Cold Low Heavy
Cool/Cold No Spin Medium
Cold/Cold Light
Hot/Cold High Extra Heavy
Warm/Cold Low Heavy
Cool/Cold No Spin Medium
Cold/Cold Light
Hot/Cold
Warm/Cold
Cool/Cold
Cold/Cold
Hot/Cold
Warm/Cold
Cool/Cold
Cold/Cold
Extra Rinse
Extra Rinse
High Extra Heavy Extra Rinse
Heavy
Medium
Light
High Extra Heavy Extra Rinse
Heavy
Medium
Light
Hot/Cold High Extra Heavy
Warm/Cold Low Heavy
Cool/Cold No Spin Medium
Cold/Cold Light
Extra Rinse
Use this cycle to wash lightly soiled
garments indicating "Machine Washable
Silks" or "Gentle" cycle on the care label.
Place small items in mesh garment bags
before washing.
Use this cycle to wash small, lightly
soiled loads of 2-3 items that are needed
in a hurry.
Use this cycle for normally soiled cottons
and mixed fabric loads. High speed spin
is the only spin speed available for the
Normal cycle.
The Eco Normal cycle allows you to
increase your energy savings compared to
the Normal cycle. When this cycle is used,
the wash cycle will use cooler wash water
temperatures than the Normal cycle.
Use this cycle to wash loads of no-iron
fabrics such as sport shirts, blouses,
casual business clothes, permanent
press, and blends.
Extra Rinse
Large items
such as sleeping
bags, small
comforters,
jackets
Sturdy fabrics,
colorfast items,
towels, jeans
Swimsuits and
items requiring
rinsing without
detergent
Hand-wash items
Heavily soiled
fabrics
Bulky Hot/Cold
Items Warm/Cold
Cool/Cold
Cold/Cold
Heavy Hot/Cold
Duty Warm/Cold
Cool/Cold
Cold/Cold
Rinse & Hot/Cold
Spin Warm/Cold
Cool/Cold
Cold/Cold
Drain &
Spin
Soak Hot/Cold
Warm/Cold
Cool/Cold
Cold/Cold
Hot/ColdClean
Washer
with
Affresh ®
High Extra Heavy
Low Heavy
No Spin Medium
Light
High Extra Heavy
Low Heavy
No Spin Medium
Light
High
Low
No Spin
High
Low
No Spin
No Spin Extra Heavy
Heavy
Medium
Light
High Extra Heavy
No clothes in
washer
Extra Rinse
Use this cycle to wash large items such as
jackets and small comforters. The washer
will fill with enough water to wet down the
load before the wash portion of the cycle
begins. Do not overload basket.
Use this cycle for heavily soiled or
sturdy items. Water-level sensing process
may take longer for some items than for
others because they will absorb more
water than other fabric types.
Combines a rinse and high speed
spin for loads requiring an additional
rinse cycle or to complete a load after
power interruption.
Also use for loads that require rinsing only.
This cycle uses a spin to shorten drying
times for heavy fabrics or special-care
items washed by hand. Use this cycle to
drain washer after cancelling a cycle or
completing a cycle after a power failure.
Select Soil Level to adjust soaking cycle
time. After time has expired, water will
drain but washer will not spin.
Use once a month to keep the inside
of the washer fresh and clean. Higher
water levels and Affresh ®work together
to thoroughly clean the washer interior.
5

USING YOUR WASHER
Fire Hazard
Never place items in the washer that are dampened
with gasoline or other flammable fluids.
No washer can completely remove oil.
Do not dry anything that has ever had any type of oil on
it (including cooking oils).
Doing so can result in death, explosion, or fire.
"1, Sort and prepare your laundry
• Empty pockets. Loose change, buttons, or any small object
can pass under the washplate and become trapped, causing
unexpected sounds.
• Sort items by recommended cycle, water temperature,
and colorfastness.
• Separate heavily soiled items from lightly soiled.
• Separate delicate items from sturdy fabrics.
• Do not dry garments if stains remain after washing, because
heat can set stains into fabric.
• Treat stains promptly.
• Close zippers, fasten hooks, tie strings and sashes, and
remove non-washable trim and ornaments.
• Mend rips and tears to prevent further damage to items
during washing.
Helpful Tips:
= When washing water-proof or water-resistant items, load
evenly. See "Cycle Guide" for tips and more information on
using the Bulky Items cycle.
• Use mesh garment bags to help prevent tangling when
washing delicate or small items.
• Turn knits inside out to prevent pilling. Separate lint-takers
from lint-givers. Synthetics, knits, and corduroy fabrics will
pick up lint from towels, rugs, and chenille fabrics.
Always read and follow fabric care label instructions to avoid
damage to your garments.
Electrical Shock Hazard
Plug into a grounded 3 prong outlet.
Do not remove ground prong.
Do not use an adapter.
Do not use an extension cord.
Failure to follow these instructions can result in death,
fire, or electrical shock.
Load garments in loose heaps evenly around basket wall.
For best results, do not load higher than the recommended
maximum load height. Do not wrap large items such as sheets
around the washplate; load them in loose piles around the sides
of the basket. Try mixing different sized items to reduce tangling.
IMPORTANT: Do not overload or force items into washer.
items need to move freely. Overloading can lead to poor
cleaning performance, and may increase wrinkling and tangling.
maximum load height
m
6

Using Laundry Product Dispensers
Add HE detergent to dispenser
Detergent tray
Add a measured amount of HE detergent
into detergent tray. This tray holds 3 oz.
(89 mL). Do not overfill tray - adding too much detergent may
cause detergent to be dispensed into the washer too early.
IMPORTANT: Use only High Efficiency detergents. The package
will be marked "HE" or "High Efficiency." Low-water washing
creates excessive sudsing with a regular non-HE detergent.
Using regular detergent will likely result in longer cycle times and
reduced rinsing performance. It may also result in component
failures and noticeable mold or mildew. HE detergents are made
to produce the right amount of suds for the best performance.
Follow the manufacturer's instructions to determine the amount
of detergent to use.
Using Oxi or color-safe bleach:
If using an Oxi or color-safe bleach laundry boost product, add
to the bottom of the washer basket before adding clothes.
HELPFUL TIP: See "Washer Maintenance" for information
on recommended method of cleaning washer dispenser trays.
to dispenser
Do not overfill, dilute, or use more than 1 cup (250 mL).
Do not use color-safe bleach or Oxi products in the same
cycle with liquid chlorine bleach.
Fabric softener tray
CD
Fabric
Softener
Pour a measured amount of liquid fabric softener
into tray, always follow manufacturer's directions
for correct amount of fabric softener based on your load size.
Close dispenser drawer, then select Fabric Softener option.
IMPORTANT: Fabric Softener option must be selected to
ensure proper distribution at correct time in cycle. Do not overfill
or dilute. Overfilling dispenser will cause fabric softener to
immediately dispense into washer.
If Extra Rinse option is selected, fabric softener will be dispensed
into the last rinse.
It is normal for a small amount of water to remain in the dispenser
at the end of a cycle.
Starting Your Washer
(}. Press POWER to turn on washer
POWER
Make sure the dispenser drawer is closed completely, then press
POWER to turn on the washer.
7. Select cycle
NORMAL
QUICKWASH
DELICATE
CLEAI'
WASHER
with a_
DRAIN & SPIN
CASUAL
BULKY
ITEMS
HEAVY
DUTY
RINSE& SPIN
Turn cycle knob to choose your wash cycle. For more
information, see "Control Panel". 7

8. Select cycle settings
l Hot l Extra Heavy
Warm l Heavy IHigh
_i IM_I: um ILNWspin
Temp Soil Spin
Level Speed
Once you select a cycle, the default settings for that cycle will be
lit. Press the cycle settings buttons to change the Temperature,
Soil Level, and Spin Speed, if desired.
Always read and follow fabric care label instructions to avoid
damage to your garments.
Hot
Some cold water is added to save
energy. This will be cooler than
Warm
Some cold water will be added,
so this will be cooler than what
your previous washer provided.
Whites and pastels
Durable garments
Bright colors
Moderate to light soils
Cool - brights/darks _:
Warm water is added to assist Colors that
in soil removal and to help bleed or fade
dissolve detergents. Light soils
Cold
Warm water may be added to Dark colors that
assist in soil removal and to help bleed or fade
dissolve detergents. Light soils
0. Press START/Pause/Unlock
to begin wash cycle
C3
START
Pause/Unlock
Press the START/Pause/Unlock button to start the wash cycle.
When the cycle has finished, the DONE indicator will light.
Promptly remove garments after cycle has completed to prevent
odor, reduce wrinkling, and rusting of metal hooks, zippers, and
snaps.
Unlocking the lid to add garments: c_
If you need to open the lid to add 1 or 2
missed garments, you may do so during the
first portion of the Sensing step.
Press START/Pause/Unlock; the lid will unlock Pause/Unlock
once the washer movement has stopped. This
may take several minutes if the load was spinning at high speed.
Then close the lid and press START/Pause/Unlock again to
restart the cycle.
If lid is left open for more than 10 minutes, water will pump out.
START
9, Select cycle options
CD CD
Fabric Extra
Softener Rinse
Select any other cycle options you may wish to add, if not
previously set. Some cycles will automatically add certain
options such as Extra Rinse. These can be turned off, if desired.
NOTE: Not all options are available with all cycles.
8

WASHER INWENANCE
WATER iNLET HOSES
Replace inlet hoses after 5 years of use to reduce the risk
of hose failure. Periodically inspect and replace inlet hoses
if bulges, kinks, cuts, wear, or leaks are found.
When replacing your inlet hoses, mark the date of
replacement on the label with a permanent marker.
CLEANING YOUR WASHER
Keep your washer as clean and fresh as your clothes.
To keep washer interior odor-free, follow this recommended
monthly cleaning procedure:
1. Make sure the washer is empty.
2. Using recommended AFFRESH®washer cleaner, add one
tablet to washer drum
OR
If using liquid chlorine bleach, add 1 cup (250 mL) to liquid
chlorine bleach dispenser.
\
\
IMPORTANT: Do not add detergent to CLEAN WASHER
with AFFRESH TM cycle. Do not use more than recommended
amount of bleach to avoid damaging product over time.
3. Close washer lid.
4. Press POWER.
5. Select CLEAN WASHER with AFFRESH TM cycle.
6. Press START/Pause/Unlock. Water will pour into washer
for a moment and pause, lid will lock, then cycle
will continue.
NOTE: For best results, do not interrupt cycle. If cycle must
be interrupted, press START/Pause/Unlock twice and run
a RINSE AND SPIN cycle to ensure cleaner or bleach have
been rinsed from washer.
To clean exterior:
1. Use a soft, damp cloth or sponge to wipe up any spills.
2. Use all-purpose surface cleaner, if needed.
IMPORTANT: To avoid damaging the washer's finish, do not
use abrasive products.
"- CLEANING YOUR DISPENSER TRAY '_
You may find laundry product residue in your dispenser
trays. To remove residue, follow this recommended cleaning
procedure:
1. Pull tray out until you feel resistance.
2. Lift up slightly, and then continue pulling out.
3. Wash in warm, soapy water, using a mild detergent.
4. Rinse with warm water.
5. Air dry, or dry wtih a towel, then place back into slot.
iMPORTANT: Dispenser trays are not dishwasher safe.
NON=USE AND VACATION CARE
Operate your washer only when you are home.
If moving, or not using your washer for a period of time,
follow these steps:
1. Unplug or disconnect power to washer.
2. Turn off water supply to washer, to avoid flooding due
to water pressure surge.
fWINTER STORAGE CARE
iMPORTANT: To avoid damage, install and store washer
where it will not freeze. Because some water may stay in
hoses, freezing can damage washer. If storing or moving
during freezing weather, winterize your washer.
To winterize washer:
1. Shut off both water faucets, disconnect and drain water
inlet hoses.
2. Put 1 qt. (1 L) of R.V.-type antifreeze in basket and run
washer on RINSE AND SPIN cycle for about 30 seconds
to mix antifreeze and remaining water.
3. Unplug washer or disconnect power.
9

TRANSPORTING YOUR WASHER
1. Shut off both water faucets. Disconnect and drain water
inlet hoses.
2. If washer will be moved during freezing weather, follow
WINTER STORAGE CARE directions before moving.
3. Disconnect drain from drain system and drain any
remaining water into a pan or bucket. Disconnect drain
hose from back of washer.
4. Unplug power cord.
5. Place inlet hoses and drain hose inside washer basket.
6. Drape power cord over edge and into washer basket.
7. Place packing tray from original shipping materials back
inside washer. If you do not have packing tray, place heavy
blankets or towels into basket opening. Close lid and place
tape over lid and down front of washer. Keep lid taped until
washer is placed in new location.
Electrical Shock Hazard
Plug into agrounded 3 prong outlet,
Do not remove ground prong.
Do not use an adapter.
Do not use an extension cord.
Failure to follow these instructions can result in death,
fire, or electrical shock.
RE! NSTALLING/USI NG WASHER AGAI N
To reinstall washer after non-use, vacation, winter storage,
or moving:
1. Refer to Installation Instructions to locate, level, and
connect washer.
2. Before using again, run washer through the following
recommended procedure:
To use washer again:
1. Flush water pipes and hoses. Reconnect water inlet
hoses. Turn on both water faucets.
2. Plug in washer or reconnect power.
3. Run washer through BULKY ITEMS cycle to clean
washer and remove antifreeze, if used. Use only HE
High Efficiency detergent. Use half the manufacturer's
recommended amount for a medium-size load.
10

TROUBLESHOOTING
rFirst try the solutions suggested here or visit our website at www.whirlpool.com/help
for assistance and to possibly avoid a service call.
If you experience
Check the following for
proper installation or see
"Using Your Washer"
section.
Feet may not be in contact with the
floor and locked.
Washer may not be level.
Load could be unbalanced.
Front and rear feet must be in firm contact with floor, and washer
must be level to operate properly. Jam nuts must be tight
against the bottom of the cabinet.
Check floor for flexing or sagging. If flooring is uneven, a 3/4"
(19 mm) piece of plywood under your washer will reduce sound.
See "Level the Washer" in InstNlation Instructions.
Load dry items in loose heaps evenly around basket wall.
Adding wet items to washer or adding more water to basket
could unbalance washer.
Do not overload. Do not fill above the stainless steel portion of
basket. Avoid washing single items.
Use Bulky Item cycle for oversized, non-absorbent items such as
comforters or poly-filled jackets.
See "Cycle Guide" and "Using Your Washer" in this Use and
Care Guide.
Clicking or metallic
noises
Gurgling or humming
Objects caught in washer
drain system.
Washer may be
draining water.
Empty pockets before washing. Loose items such as coins
could fall between basket and tub or may block pump.
It may be necessary to call for service to remove items.
It is normN to hear metal items on clothing such as metal snaps,
buckles, or zippers touch against the stainless steel basket.
It is normal to hear the pump making a continuous humming sound
with periodic gurgling or surging asfinn amounts of water are
removed during the spin/drain cycles.
Check the following for Washer not level. Water may splash off basket if washer is not level.
proper installation: Check that load is not unbalanced or overloaded.
Fill hoses not attached tightly. Tighten fill-hose connection.
Fill hose washers Are all four fill hose flat washers properly seated?
Drain hose connection
Check household plumbing for leaks
or clogged sink or drain.
Washer not loaded properly.
Pull drain hose from washer cabinet and properly secure it to
drainpipe or laundry tub.
Do not place tape over drain opening.
Water can back up out of a clogged sink or drainpipe. Check
all household plumbing for leaks (laundry tubs, drain pipe,
water pipes, and faucets.)
Improper loading can cause basket to be out of alignment
and cause water to splash off tub. See "Getting Started"
for loading instructions.
Not enough water
in washer Load not completely covered
in water. This is normal operation for an HE low-water washer. The load will
not be completely underwater. The washer senses load sizes and
adds correct amount of water for optimal cleaning. See "What's
New under the Lid."
IMPORTANT: Do not add more water to washer. The added water
lifts the load off the washplate, resulting in less cleaning. J
11

TROUBLESHOOTING
Electrical Shock Hazard
Plug into a grounded 3 prong outlet.
Do not remove ground prong.
Do not use an adapter.
Do not use an extension cord.
Failure to follow these instructions can result in death,
fire, or electrical shock.
f
ff you experience
Washer won't run or fill,
washer stops working
First try the solutions suggested here or visit our website at www.whirlpool.com/help "_
for assistance and to possibly avoid a service call.
i
Check for proper water supply. Both hoses must be attached and have water flowing to
inlet valve.
Check proper electrical supply.
Normal washer operation.
Washer may be overloaded.
Not using HE detergent or using too
much HE detergent.
Both Hot and Cold water faucets must be turned on.
Check that inlet valve screens have not become clogged.
Check for any kinks in inlet hoses, which can restrict water flow.
Plug power cord into a grounded 3 prong ou;_let.
Do not use an extension cord.
Ensure there is power to outlet.
Reset a tripped circuit breaker. Replace any blown fuses.
NOTE: If problems continue, contact an electrician.
Lid must be closed for washer to run.
Washer will pause during certain phases of cycle.
Do not interrupt cycle.
Washer may be stopped to reduce suds.
Washer spins the load before filling to determine load size.
Remove several items, rearrange load evenly in basket and add
detergent. Close lid and press START/Pause/Unlock.
Do not add more than 1 or 2 addNonal items after cycle has
started to avoid overloading or unbalancing.
Do not add more water to the washer.
Only use HE detergent. Suds from regular detergents can slow
or stop the washer. Always measure detergent and follow
detergent directions based on your load requirements.
To remove suds, cancel cycle. Select DRAIN & SPIN. Select your
cycle. Press START/Pause/Unlock. Do not add more detergent..,/
12

TROUBLESHOOTING
f First try the solutions suggested here or visit our website at www.whirlpool.com/help
for assistance and to possibly avoid a service call.
If you experience
Washer not draining/
spinning, loads are
still wet
Dry spots on load
after cycle
i,, ,,,,,,,,,,,,,,,,,,,,,,,,,,,,
Incorrect or wrong
wash or rinse
temperatures
Load not rinsed
Empty pockets and use garment bags
for small items.
Use a cycle with a high spin speed.
The washer may be overloaded or
unbalanced.
Check plumbing for correct drain
hose installation. Drain hose extends
into standpipe farther than 4.5"
(114 mm).
Wrong or too much detergent
causing suds to slow or stop
draining and spinning?
High speed spins extract more
moisture than traditional topqoad
washers.
Check for proper water supply.
Energy saving controlled
wash temperatures.
Check for proper water supply.
Not using HE detergent or using too
much HE detergent.
Washer not loaded as recommended.
Small items may have been caught in pump or between basket
and tub, which can slow draining.
Cycles with lower spin speeds remove less water than cycles
with high spin speeds. Use the recommended cycle/speed spin
for your garment. To remove extra water in the load, select
Drain & Spin. Load may need to be rearranged to allow even
distribution of the load in the basket.
Overloading or unbalanced loads will not allow the washer to
spin correctly, leaving the load wetter than normal. See "Using
Your Washer" for loading recommendations.
Check drain hose for proper installation. Use drain hose form
and securely attach to drainpipe or tub. Do not tape over drain
opening.
Lower drain hose if the end is higher than 96" (2.4 m) above the
floor. Remove any clogs from drain hose.
Use only HE detergent. Always measure and follow detergent
directions for your load. To remove extra suds, select DRABN&
SPHN.Do not add detergent.
The high spin speeds combined with air flow during the final
spin can cause items near the top of the load to develop dry
spots during the finn spin. This is normal.
Are hot and cold inlet hoses reversed?
Both hoses must be attached to both washer and faucet, and
have both hot and cold water flowing to inlet valve.
Check that inlet valve screens are not clogged.
Remove any kinks in hoses.
Energy Star washers use cooler wash and rinse water
temperatures than your previous washer. This includes
cooler hot and warm washes.
Are hot and cold inlet hoses reversed?
Both hoses must be attached and have water flowing to the
inlet valve.
Both hot and cold water faucets must be on.
Inlet valve screens on washer may be clogged.
Remove any kinks in the inlet hose.
The suds from regular detergent can prevent washer
from operating correctly.
Use only HE detergent. Be sure to measure correctly.
Always measure detergent and follow detergent directions
based on load size and soil level.
The washer is less efficient at rinsing when overloaded.
Load garments in loose heaps evenly around the basket wall.
Do not load above the stainless steel portion of the basket. The
washer will not rinse well if overloaded. Load with dry items only.
Use cycle designed for the fabrics being washed.
Add only 1 or 2 garments after washer has started. J
13

TROUBLESHOOTING
First try the solutions suggested here or visit our website at www.whirlpool.com/help -_
for assistance and to possibly avoid a service call.
If you experience Possible Causes Solution
Add an Extra Rinse to the selected cycle.Sand, pet hair, lint, etc.
on load after washing
ii,,,,,iiiiiii
Load istangling
Not cleaning or
removing stains
Incorrect dispenser
operation
Heavy sand, pet hair, lint, and
detergent or bleach residues
may require additional rinsing.
Washer not loaded as recommended.
Wash load not completely
covered in water.
Added more water to washer.
Washer not loaded properly.
Not using HE detergent or using too
much HE detergent.
Not using correct cycle for fabric type.
Not using dispensers.
Not washing like colors together.
Clogged dispensers or laundry
products dispensing too soon.
See "Using Your Washer" section.
Select a cycle with a slower wash action and spin speed;
however, items will be wetter than those using a higher
speed spin.
Load garments in loose heaps evenly around the basket wall.
Do not load above the stainless steel portion of the basket.
Reduce tangling by mixing types of load items. Use the
recommended cycle for the type of garments being washed.
Washer senses load size and adds correct amount of water.
This is normal and necessary for clothes to move.
Added water lifts the laundry off the washplate, resulting in less
effective cleaning.
Washer is less efficient at cleaning when overloaded.
Load garments in loose heaps evenly around the basket wall.
Do not load above the stainless steel portion of
basket. Load with dry items only.
Add only 1 or 2 garments after washer has started.
The suds from regular detergent can prevent washer from
operating correctly.
Use only HE detergent. Be sure to measure correctly.
Always measure detergent and follow manufacturer's directions
based on load size and soil level.
Use a higher soil level cycle option and warmer wash
temperature to improve cleaning.
If using Quick Wash cycle, wash only a few items.
Use Whites and Heavy Duty cycle for tough cleaning.
Use dispensers to avoid chlorine bleach and fabric softener
staining.
Load dispensers before starting a cycle.
Avoid overfilling.
Do not add products directly to load.
Wash like colors together and remove promptly after the cycle is
complete to avoid dye transfer.
Do not overfill dispenser, which causes immediate dispensing.
Always select Fabric Softener and/or Oxi option to assure
proper dispensing.
Load dispensers before starting a cycle.
It isnormal for small amounts of water to be remain in dispenser.
Homes with low water pressure may result in residual powder in the
dispenser. Toavoid, select a warmer wash temperature if possible,
depending on your load, or use liquid HE detergent.
Use only liquid chlorine bleach in the bleach dispenser, j
14

TROUBLESHOOTING
First try the solutions suggested here or visit our website at www.whirlpool.com/help "_
for assistance and to possibly avoid a service call.
mfyou experience Possible Causes Solution
Fabric Damage Sharp items were in pockets during Empty pockets, zip zippers, and snap or hook fasteners before
wash cycle, washing to avoid snags and tears.
Strings and straps could have tangled. Tie all strings and straps before starting wash load.
Mend rips and broken threads in seams before washing.
No sound when
buttons are pressed
Odors
Htemsmay have been damaged before
washing.
Fabric damage can occur if washer is
overloaded.
Liquid chlorine bleach may have been
added incorrectly.
Garment care instructions may not
have been followed.
Button sounds are turned off.
Monthly maintenance not done as
recommended.
Using wrong or too much detergent.
Load garments in loose heaps evenly around the basket wall.
Do not load above the stainless steel portion of the basket.
Load with dry items only.
Use cycle designed for the fabrics being washed.
Add only 1 or 2 garments after washer is started.
Do not pour liquid chlorine bleach directly onto load. Wipe up
bleach spills.
Undiluted bleach will damage fabrics. Do not use more than
recommended by manufacturer.
Do not place load items on top of bleach dispenser when
loading and unloading washer.
Always read and follow garment manufacturer's care
label instructions.
Button sounds can be turned on or off by pressing and holding
Cycle Signal for 5 seconds.
Run the Clean Washer cycle with AFFRESH TM monthly.
See "Cleaning Your Washer" in Washer Maintenance.
Unload washer as soon as cycle is complete.
Use only HE detergent. Be sure to measure correctly.
Always follow the manufacturer's directions.
See "Cleaning your Washer" section. J
15

WHIRLPOOLCORPORATIONLAUNDRYWARRANTY
LIMITED WARRANTY
For one year from the date of purchase, when this major appliance is operated and maintained according to instructions attached to or
furnished with the product, Whirlpool Corporation or Whirlpool Canada LP (hereafter "Whirlpool") will pay for Factory Specified Parts
and repair labor to correct defects in materials or workmanship that existed when this major appliance was purchased. Service must be
provided by aWhirlpool designated service company. YOUR SOLE AND EXCLUSIVE REMEDY UNDER THIS LIMITED WARRANTY
SHALL BE PRODUCT REPAIR AS PROVIDED HEREIN. This limited warranty is valid only in the United States or Canada and applies
only when the major appliance is used in the country in which it was purchased. Proof of original purchase date is required to obtain
service under this limited warranty.
ITEMS EXCLUDED FROM WARRANTY
This limited warranty does not cover:
1. Replacement parts or repair labor if this major appliance is used for other than normal, single-family household use or when it is
used in a manner that is inconsistent to published user or operator instructions and/or installation instructions.
2. Service calls to correct the installation of your major appliance, to instruct you on how to use your major appliance, to replace or
repair house fuses, or to correct house wiring or plumbing.
3. Service calls to repair or replace appliance light bulbs, air filters or water filters. Consumable parts are excluded from warranty
coverage.
4. Damage resulting from accident, alteration, misuse, abuse, fire, flood, acts of God, improper installation, installation not in
accordance with electrical or plumbing codes, or use of products not approved by Whirlpool.
5. Cosmetic damage, including scratches, dents, chips or other damage to the finish of your major appliance, unless such damage
results from defects in materials or workmanship and is reported to Whirlpool within 30 days from the date of purchase.
6. Pick up and delivery. This major appliance is intended to be repaired in your home.
7. Repairs to parts or systems resulting from unauthorized modifications made to the appliance.
8. Expenses for travel and transportation for product service if your major appliance is located in a remote area where service by an
authorized Whirlpool servicer is not available.
9. The removal and reinstallation of your major appliance if it is installed in an inaccessible location or is not installed in accordance
with Whirlpool's published installation instructions.
10. Replacement parts or repair labor on major appliances with original model/serial numbers that have been removed, altered, or
cannot be easily determined.
DISCLAIMER OF IMPLIED WARRANTIES
IMPLIED WARRANTIES, INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY OR IMPLIED WARRANTY OF FITNESS FOR
A PARTICULAR PURPOSE, ARE LIMITED TO ONE YEAR OR THE SHORTEST PERIOD ALLOWED BY LAW. Some states and provinces
do not allow limitations on the duration of implied warranties of merchantability or fitness, so this limitation may not apply to you. This
warranty gives you specific legal rights, and you also may have other rights that vary from state to state or province to province.
LIMITATION OF REMEDIES; EXCLUSION OF INCIDENTAL AND CONSEQUENTIAL DAMAGES
YOUR SOLE AND EXCLUSIVE REMEDY UNDER THIS LIMITED WARRANTY SHALL BE PRODUCT REPAIR AS PROVIDED HEREIN.
WHIRLPOOL SHALL NOT BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES. Some states and provinces do not allow
the exclusion or limitation of incidental or consequential damages, so these limitations and exclusions may not apply to you. This
warranty gives you specific legal rights, and you also may have other rights that vary from state to state or province to province.
If outside the 50 United States and Canada, contact your authorized Whirlpool dealer to determine if another warranty applies.
Ifyou think you need repair service, first see the "Troubleshooting" section of the Use & Care Guide. If you are unable to resolve the
problem after checking "Troubleshooting," additional help can be found by checking the "Assistance or Service" section or by calling
Whirlpool. In the U.S.A., call 1-800-253-1301. In Canada, call 1-800-807-6777. 7/08
Keep this book and your sales slip together for future
reference. You must provide proof of purchase or installation
date for in-warranty service.
Write down the following information about your major appliance
to better help you obtain assistance or service if you ever need it.
You will need to know your complete model number and serial
number. You can find this information on the model and serial
number label located on the product.
Dealer name
Address
Phone number
Model number
Serial number
Purchase date
16

p p
$ECURITE DE LA LA USE
Votre s_curit6 et celle des autres est tres importante,
Nous donnons de nombreux messages de securit6 importants dans ce manuel et sur votre appareiJ menager.
Assurez=vous de toujours lire tousles messages de s6curit6 et de vous y conformer.
Voici le symbole d'alerte de s6curit6.
Ce symbole d'alerte de s6curite vous signale les dangers potentiels de d6ces et de blessures graves
& vous et & d'autres.
Tous les messages de securit6 suivront le symbole d'alerte de securit6 et le mot "DANGER" ou
"AVERTISSEMENT". Ces mots signifient :
Risque possible de d6c_s ou de blessure grave sJ
vous ne suivez pas irnm_diatement les instructions,
Risque possible de d_c_s ou de blessure grave
si vous ne suivez pas les instructions.
Tousles messages de securit6 vous diront quel est le danger potentiel et vous disent comment reduire le risque de
blessure et ce qui peut se produire en cas de non-respect des instructions.
IMPORTANTES INSTRUCTIONS DE SI'=CURITE
AVERTISSEMENT : Pour r6duire les risques d'incendie, de choc _lectrique ou de blessures Iors de I'utilisation de la
laveuse, suivre les precautions fondamentales dont les suivantes :
[] Lire toutes les instructions avant d'utiliser la laveuse.
[] Ne pas laver des articles qui ont 6t6 nettoy6s ou
laves avec de I'essence ou imbibes d'essence,
solvants de nettoyage &sec, ou autres substances
inflammables ou explosives; ces substances
peuvent emettre des vapeurs susceptibles de
s'enflammer ou d'exploser.
[] Ne pas ajouter d'essence, solvant de nettoyage
sec ou autre produit inflammable ou explosif dans
I'eau de lavage. Ces substances peuvent 6mettre
des vapeurs susceptibles de s'enflammer ou
d'exploser.
[] Dans certaines conditions, de I'hydrog_ne gazeux
peut se former dans un circuit d'eau chaude qui n'a
pas et6 utilis6 pendant 2 semaines ou plus. LE GAZ
HYDROGI_NE EST EXPLOSIBLE. Si le circuit d'eau
chaude n'a pas 6t6 utilis6 pendant une telle p6riode,
avant d'utiliser la laveuse, ouvrir tousles robinets
d'eau chaude et laisser I'eau s'6couler pendant
plusieurs minutes par chaque robinet. Ceci
permettra l'6vacuation de I'hydrogene gazeux
accumul6. Comme ce gaz est inflammable, ne pas
fumer ou utiliser une flamme nue au cours de cette
periode.
[] Ne pas laisser des enfants jouer sur ou &I'int6rieur de la
laveuse. Bien surveiller les enfants Iorsque la laveuse est
utilis6e & proximit6 d'enfants.
[] Avant de mettre la laveuse au rebut ou hors de service,
enlever la porte ou le couvercle.
[] Ne pas tenter d'atteindre un article b.I'interieur de la cuve de
la laveuse Iorsque le tambour, la cuve ou I'agitateur est en
mouvement.
[] Ne pas installer ou remiser cette laveuse & un endroit oQ elle
serait expos6e aux intemp6ries.
[] Ne pas modifier les organes de commande.
[] Ne pas r6parer ou remplacer un composant quelconque de
la laveuse, ni entreprendre une op6ration de service, si ce
n'est sp_cifiquement recommand_ dans ce manuel ou dans
un manuel d'instructions de r6parations destin6 b.I'utilisateur;
iJest alors essentiel que la personne concern6e comprenne
ces instructions et soit comp6tente pour les ex_cuter.
[] Voir "Sp6cifications 6lectriques" pour les instructions de
liaison & la terre.
CONSERVEZ CES INSTRUCTIONS
Avertissements de la proposition 65 de I'letat de Californie :
AVERTISSEMENT : Ce produit contient un produit chimique connu par I'Fttat de Californie pour &tre a I'origine de cancers.
AVERTISSEMENT : Ce produit contient un produit chimique connu par I'l_tat de Califomie pour _tre a I'origine de malformations
et autres d6ficiences de naissance.
17

QUOI DE NEUF $OUS LE COUWERCLE?
Nettoyer avec moins d eau
Laveuse traditionnelle
de type agitateur
Impulseur
Laveuse a faible
consommation d'eau
avec impulseur
La nouveaut6 la plus flagrante de cette nouvelle laveuse est
son systeme de lavage a faible consommation d'eau avec
impulseur. La laveuse ajuste automatiquement le niveau d'eau
en fonction de la taille de la charge - nul besoin de s61ecteur
de niveau d'eau.
A mesure que la laveuse imbibe et d6place la charge, les
v@tements se tassent dans le panier. Ceci est normal et ne
signifie pas que I'on doive rajouter des v#.tements.
IMPORTANT : Vous ne verrez pas de panier de laveuse rempli
d'eau, comme avec votre pr6c6dente laveuse de type agitateur.
L__
Lorsque I'on charge la laveuse de linge sale, celui-ci doit
6tre r6parti uniform6ment le long des parois du panier. Pour
de meilleurs r6sultats, ne pas remplir au-dela de la hauteur
de charge maximale recommand6e.
Automatic Load Size Sensing
Une fois que I'on d6marre le programme, le couvercle se
verrouille et la laveuse entame un processus de d6tection pour
d6terminer le niveau d'eau appropri6 a la charge. Cela peut
prendre plusieurs minutes. Voir la description pas-a-pas dans la
section "T6moins lumineux de programme".Voir la description
pas-a-pas dans la section "T6moins lumineux de programme".
Choix du d6tergeat appropri6
Utiliser uniquement des d6tergents Haute efficacit6. Uemballage
portera la mention, HE, ou, High Efficiency, (haute efficacit6).
Un lavage avec faible consommation d'eau produit un exces
de mousse avec un d6tergent non HE ordinaire. II est probable
que I'utilisation d'un d6tergent ordinaire prolongera la dur6e
des programmes et r6duira la performance de ringage. Ceci
peut aussi entrainer des d6faillances des composants et une
moisissure perceptible. Les d6tergents HE sont congus pour
produire la quantit6 de mousse ad6quate pour le meilleur
rendement. Suivre les recommandations du fabricant pour
d6terminer la quantit6 de d6tergent a utiliser.
Utiliser uniquement un detergent Haute efficacite (HE).
Nettoyage coaceatr6
Le systeme de lavage Afaible consommation d'eau signifie
un lavage concentr6. Plut6t que de diluer du d6tergent comme
dans une laveuse de type agitateur, cette laveuse libere
le d6tergent uniquement sur les endroits souill6s.
De I'eau est ajout6e a la charge pendant que le panier tourne
lentement. Cette m6thode de lavage avec faible consommation
d'eau utilise moins d'eau et d'6nergie qu'une laveuse
traditionnelle de type agitateur.
Soas normaux pr6visibles
Au cours de diff6rents stades du programme de lavage, vous
entendrez peut-_tre des bruits que votre laveuse pr6c6dente
ne produisait pas. Par exemple, vous entendrez peut-6tre
un cliquetis au d6but du programme Iorsque le systeme de
verrouillage du couvercle effectue un test automatique. On
entendra diff6rents bourdonnements et bruits de frottements
rythmiques a mesure que I'impulseur d_place la charge. Parfois,
il est possible que la laveuse soit completement silencieuse,
Iorsqu'elle d_termine le niveau d'eau ad_quat ou qu'elle laisse
tremper les v_tements.
18

LE,AU DE COM DE ET C, CTERISTIQUE$
NODAL
QUICKWASH
POWER
Fabric
Softener
o I
HEAVY _ l
DUTY Hot
START Warm
Pause/Unlock
withaff_S_ Cool
Cold
DRAIN & SPIN L_J
o
SensingWash R_e SPin D°ne LocUdk Extra Temp
Rinse
I I
@
II
Heavy igh
Medium
Light pin
Soil Spin
Level Speed
[]
@
@
BOUTON DE PROGRAMME DE LAVAGE
Utiliser le bouton de programme pour s61ectionner les
programmes disponibles de la laveuse un programme
correspondant a la charge de linge. Voir "Guide de
programmes" pour des descriptions de programmes
d6taill6es.
OPTIONS DE PROGRAMMES
Lorsqu'on s61ectionne un programme, ses r6glages par
d6faut s'allument. Certains programmes et options ne
sont pas disponibles sur certains modules.
TEMP
La fonction de contr61e de temp6rature d6tecte et
maintient une temp6rature uniforme de I'eau en r6gulant
le d6bit d'arriv6e d'eau chaude et d'eau froide.
S61ectionner une temp6rature de lavage en fonction
du type de tissu et de salet6 a laver. Pour des r6sultats
optimaux, suivre les instructions sur 1'6tiquette du
v&tement et utiliser la temp6rature d'eau de lavage la plus
chaude possible qui reste sans danger pour le tissu.
• Les temp6ratures de I'eau tiede et de I'eau chaude
seront inf6rieures a celles de votre pr6c6dente laveuse.
• M_me avec un r6glage de lavage a I'eau froide, il est
possible que de I'eau tiede soit ajout6e a la laveuse
pour maintenir une temperature minimale.
NIVEAU DE SALETle
Le niveau de salet6 (dur6e de lavage) est pr6r6gl6 pour
chaque programme de lavage.
Pour la plupart des charges, utiliser le niveau de salet6
pr6r6gl6 pour le programme choisi. Pour les tissus tr_s
sales et robustes, appuyer sur Soil Level (niveau de
salet6) pour prolonger la dur6e de lavage si n6cessaire.
Pour les tissus peu sales et d61icats, appuyer sur Soil
Level (niveau de salet6) pour abr6ger la dur6e de lavage
si n6cessaire. Un r6glage de niveau de salet6 inf6rieur
aidera a r6duire I'emm61ement et le froissement.
VITESSE D'ESSORAGE
Cette laveuse s61ectionne automatiquement la vitesse
d'essorage en fonction du programme s61ectionn& Les
vitesses pr6r6gl6es peuvent 6tre modifi6es. Sur certains
programmes, certaines vitesses d'essorage ne sont pas
disponibles.
• Des vitesses d'essorage plus 61ev6es signifient des
dur6es de s6chage plus courtes mais elles peuvent
augmenter le froissement de la charge.
• Des vitesses d'essorage plus lentes signifient moins
de froissement mais laissent la charge plus humide.
O
@
O
On peut aussi ajouter ou supprimer des options pour chaque
programme. Noter que certaines options ne peuvent pas 6tre
utilis6es avec certains programmes, et que certaines d'entre
elles sont pr6r6gl6es pour ne fonctionner qu'avec certains
programmes.
EXTRA RINSE (ringage suppl_mentaire)
On peut utiliser cette option pour ajouter
automatiquement un second ringage a la plupart
des programmes.
FABRIC SOFTENER (assouplissant pour tissu)
Cette option dolt 6tre s_lectionn_e si I'on utilise
de I'assouplissant pour tissu durant un programme.
Ceci garantit que I'assouplissant pour tissu est
ajoute au bon moment Iors du ringage pour 6tre
correctement distribu&
T#MOINS LUMINEUX DES PROGRAMMES
Les t_moins lumineux indiquent la progression du
programme. A chaque _tape du processus, il est possible
que I'on remarque des pauses ou des sons diff_rents
de ceux que I'on remarque avec des laveuses ordinaires.
Sensing Wash Rinse Spin Done
SENSING (D_eTECTION)SensingWash Rinse Spin Done
Lorsqu'on appuie sur le bouton START/Pause/Unlock
(mise en marche/pause/d_verrouillage), la laveuse
effectue un test automatique sur le m_canisme de
verrouillage du couvercle. On entend un d_clic, le panier
effectue un I_ger tour, et le couvercle se d_verrouille
bri_vement avant de se verrouiller a nouveau.
Une fois que le couvercle a _t_ verrouill_ une seconde
fois, la laveuse essorage lentement la charge s_che
pour estimer la taille de la charge et la quantit_ d'eau
n_cessaire, puis elle commence a ajouter de I'eau. La
laveuse d_place ensuite bri_vement la charge, fait une
pause pour permettre & I'eau de tremper la charge,
et continue & ajouter de I'eau. Ce processus peut se
r_p_ter jusqu'& ce que la quantit_ d'eau correcte ait 6t_
ajout_e a la charge. II est aussi possible que I'on entende
de I'eau couler dans le distributeur, ajoutant le detergent
la charge.
REMARQUE : Le t_moin de detection s'allume
_galement lots des _tapes de lavage du programme.
Ceci est normal.
19

WASH (LAVAGE) Sensing Wash Rinse Spin Done
On entend I'impulseur d6placer la charge.
Contrairement aux laveuses ordinaires, la charge
n'est pas completement submerg6e dans I'eau. Un
nettoyage avec faible niveau d'eau signifie un nettoyage
concentr6. Plut6t que de diluer du d6tergent comme
dans une laveuse de type agitateur, cette laveuse libere
le d6tergent directement sur les endroits souill6s. Les
bruits 6mis par le moteur peuvent changer Iors des
diff6rentes 6tapes du programme. La dur6e de lavage
est d6termin6e par le niveau de salet6 s61ectionn6.
RINSE (RIN(_AGE} Sensing Wash Rinse Spin Done
On entend des sons similaires a ceux entendus lots
du programme de lavage a mesure que la laveuse rince
et d6place la charge. Uassouplissant pour tissu sera
distribu6 si I'option Fabric Softener (assouplissant pour
tissu) a 6t6 s61ectionn6e.
LID LOCK 0IERROUILLAGE DU COUVERCLE}
IIm Pour permettre une bonne d6tection de la charge,
le couvercle se verrouille et le t6moin de verrouillage
Lid du couvercle s'allume. Ce t6moin lumineux indique
Lock que le couvercle est verrouill6 et ne peut 6tre ouvert.
Si I'on doit ouvrir le couvercle, appuyer sur c_
START/Pause/Unlock (mise en marche/pause/
d6verrouillage). Le couvercle se d6verrouille
une fois que le mouvement de la laveuse
a cess6. IIse peut que cela prenne plusieurs ,_use/Un_ock
minutes si la laveuse essorait la charge
grande vitesse. Appuyer de nouveau sur
START/Pause/Unlock (mise en marche/pause/d6verrouillage)
pour poursuivre le programme.
START
SPIN (ESSORAGE} Sensing Wash Rinse Spin Done
La laveuse essore la charge a des vitesses augmentant
graduellement pour une bonne extraction de I'eau,
en fonction du programme et de la vitesse d'essorage
s61ectionn6e.
DONE(TERMINle) Sensing Wash Rinse Spin Done
Une fois le programme termin6, ce t6moin s'allume.
Retirer la charge rapidement pour un r6sultat optimal.
2O