Whirlpool LA6800XS User manual

AUTOMATIC
WASHER
Super Capacity
Model
LA68OOXS
Ishen. Clothes Drvm F~erers. Relrioeralot-Freemx Ice Makers Dishwashers. bill-In Ovens and Surlace Units.
Ranper,
Microwave Ovens. Trash Compaclf

Contents
Paae
PARTS AND FEATURES - 2
IMPORTANT SAFETY
INSTRUCTIONS, 3
OPERATING INSTRUCTIONS.. 4
Starting Your Washer 4
What Happens in Each Cycle 6
1 OTHER OPERATING
INSTRUCTIONS,. 12
Extra Rinse Option 12
For a Rinse and Spin 12
For a Drain and Spin
For a Soak or Pre-Wash
Liquid Bleach Dispenser
Fabric Softener Dispenser
MAGIC CLEAN’” Lint Filter
CARING FOR YOUR WASHER
Winterizing
IF YOU NEED SERVICE OR
ASSISTANCE
WASHER WARRANTY
Page
12
13
13
14
14
15
16
17
20
01988 Whirlpool Corporation
Parts and features
EXTRA RINSE
SWITCH
TEMPERATURE
SELECTOR
MODEL AND SERIAL
NUMBER PLATE
(not shown)
LIQUID BLEACH
MAGIC CLEAN@
LINT FILTER
(not shown)
LIQUID FABRIC
\ ‘TUB
Remove the Consumer
Buy Guide label. It will be
easier to remove before the
washer is used.
You should wipe out the
basket with a damp cloth
before using to remove dust
from storing or shipping.
Thank you for buying a Whirlpool appliance. Please complete and mail
the Owner Registration Card provided with this product. Then complete
the form below. Have this information ready if you need service or call with a
question.
l Copy Model and Serial Numbers
from plate (under lid near hinge]
and the purchase date from the
sales slip.
l Keep this book, your “Laundry
Guide” and your sales slip in the
Laundry Information Center.
Model Number
Serial Number
Purchase Date
Service ComDanv Phone Number
2

ALWAYS store detergent, laundry aids
and other materials in a cool, dry
place where children can’t reach
them-in a locked cabinet if possible.
ALWAYS read and follow instructions
on packages of detergent and laun-
dry aids - especially warnings and
precautions.
HAZARDOUS FUMES can be formed if
chlorine bleach is used in the same
wash as ammonia or acids such as
vinegar or rust remover,
ALWAYS unplug the power supply
cord before attempting to service the
washer.
DO NOT machine wash glass fiber
materials. Small particles can stick to
fabrics washed in following loads
and cause skin irritation.
You are personally responsible for
making sure that your washer:
l is used only for jobs normally ex-
pected of home automatic washers.
l is not run by children or anyone un-
able to operate it properly 3

Operating instructions
Starting Your Washer
Be sure to measure and add detergent, then place
a sorted load in the washer before starting it.
1
. Select a LOAD SIZE
2
Select
. WATER TEMPERATURES
l Turn the knob to point at a setting
that describes the size of load you
want to wash.
l Set the knob anywhere on or be-
tween EX SMALL (a few small items]
and EX LARGE (a full load).
l To change the water level after the
washer has started to fill, turn the knob
to RESET,then the desired water level.
NOTE: Use the EX LARGE water
level for best permanent press
Ieslllts.
l Select wash and rinse water teti-
peratures by pushing a button.
l This drawing shows a warm wash
(top temperature] and cold rinse
(bottom temperature] selection.
Recommended wash temperatures
can be found in your “Laundry Guide.”
LOAD SIZES AND WATER LEVELS
For best cleaning results, the
load must be able to move freely
in the water. Too big a load or too
little water can cause wear or
tearing of load items.
CAUTION:
DO NOT
OVERLOAD WASHER.
*Approximate
fill with load.
EX LARGE (21.7 gals./82.1 L)’
MEDIUM (16.4 galsJ62.1 L)’
EX SMALL (11.9 gals./450 L)’
4

3. Start the washer
A. Push in the Control Knob and turn
it to the right. It must be pushed in
and turned only clockwise.
B. Stop on a number in the cycle
you want. The numbers are min-
utes of wash time. The drawing
shows 10 minutes of agitation in
the REGULAR NORMAL Cycle.
C. Start the washer by pulling out
the Control Knob. The washer will
fill to the level you set with wash
water of the selected temper-
ature. After filling, the washer will
agitate for the selected number
of minutes.
D. Tostop the washer at any time,
push in the Control Knob. To
restart the washer, pull out the
Control Knob.

What Happens in Each Cycle*
Each cycle has different agitation and spin speeds designed for different
kinds of fabrics. Numbers on the dial in each cycle are the minutes of WASH
agitation time.
When the Cycle Control Knob is set to a number and pulled out, the
washer fills before agitation and timing starts. After agitation starts, the knob
turns clockwise until it points to OFF and the cycle ends.
REGULAR HEAVY Cycle
A cycle for sturdily con-
structed fabrics that are
heavily soiled.
REGULAR NORMAL Cycle
A cycle for regular loads
of fabrics that are moder-
ately soiled.
PERMANENT PRESS NORMAL Cycle
WASH
6-4
Mlnutes
High
Speed
A cycle designed for mod-
erately soiled permanent
press and some synthetic
fabrics. The cool-down
rinse helps keep wrinkles
from setting into these
items.
WASH
4
rl
I Minutes
Low
Speed
6

NOTE: You may hear the sound of water spraying during the spin parts of some
cycles. In some cycles, cold water is sprayed on the spinning load to help with
the rinsing.
Gentle Wash System
For better fabric care in the REGULAR and PERMANENT PRESScycles, the
agitation speed is reduced during the last few minutes of wash time.
SPIN
High
Speed
SPIN
High
Speed
FILL
for
Deep
Rinse
RINSE DRAIN
ILKI
SPIN
) SFzzd ) Agi&on ) ,SR[s )
t
1 Extra Rinse repeats
P I
FILL,RINSE, DRAIN and SPIN.
EXTRA
RINSE
‘cl
if
selected
Wge 12)
SPIN
High
Speed
1 Spray
Rinse
I
Extra Rinse repeats
FILL,RINSE, DRAIN and SPIN.
NOTE: Always use cold rinse water
for permanent press fabrics.

PERMANENT PRESS LIGHT Cycle
A cycle designed for
lightly soiled permanent
press and some synthetic
fabrics. The cool-down
rinse helps keep wrinkles
from setting into these items.
PARTIAL
DRAIN
L
(Pause)
KNITS/GENTLE NORMAL Cycle
A cycle that gently
washes and spins moder-
ately soiled delicate items
and washable knits.
A Indicates the machine is
pausing for a brief soak
period.
KNITS/GENTLE LIGHT Cycle
A cycle that gently
washes and spins lightly
soiled delicate items and
washable knits.
A Indicates the machine is
pausing for a brief soak
period.
8

WASH
q
NOTE: Always use cold rinse water
Low for permanent press fabrics.
Speed
---
-1-

SOAK and PRE-WASH Cycles
Brief periods of agitation
and soak time help remove
heavy soils and certain
stains that need extra
pretreatment. Use recom-
mended amount of
detergent or pre-soa k
additive. The SOAK Cycle
should always be fol-
lowed by a Wash Cycle.
SUPER WASH Cycle
Use for washing heavily
soiled loads that require
maximum soil removal.
Double the amount of
detergent recommended
when using the SUPER
WASH Cycle.
10

----
WASH DRAIN SPIN WASHER
Minutes
Hih ) Agiysion ) S”,iz(!d ) f%$
Speed
-uu-
I
Pre-wash setting begins here,
(see page 12).
Special care is needed when soaking or pre-washing laundry.
See your “Laundry Guide” for proper use of this cycle.
REFILL
u
Selkted
Level

Extra rinse option
(automatic)
For an automatic extra rinse in
the REGULAR HEAVY or REGULAR
NORMAL Cycles:
l Flip the Extra Rinse button to the
“ON” position before the REGULAR
Cycle starts. The washer will auto-
matically proceed into the extra
rinse and spin after the REGULAR
Cycle.
If no extra rinse and spin is wanted I
in a REGULAR Cycle, make sure the
button is in the “OFF” position. For an
extra rinse in other cycles, see “For
a rinse and spin:’
For a drain and spin
Other operating instructions
For a rinse and spin
(manual)
You may need an extra rinse and
spin for heavily soiled roads which
need more detergent. (Extra detergent
can require an extra Iinse.]
1. Push Control Knob in.
2. Turn clockwise to any l on the dial.
See above drawing.
3. Pull Control Knob out. The washer
will fill to selected level; agitate 2
minutes; drain and spin.
Your washer can be set to drain and
spin out water.
1. Push Control Knob in.
2. Turn clockwise to the bar just before
the OFF area in any cycle. See
drawing.
3. Pull Control Knob out. The washer
will drain and spin.
For agitation and spin speeds in each cycle, see pages 6-11.
12

For a soak or pre-wash
1. Use recommended amount of
detergent or pre-soa k product.
2. Push Control Knob in.
3. Turn clockwise to point at a number
in the SOAK Cycle. Use the 4 minute
mark for a pre-wash:
4. Pull Control Knob out. The washer
will start.
For best results, use warm water
for soaking or pre-washing stained
laundry. Hot water can set stains.
5. When the cycle is over, add
detergent for the next selected
wash cycle. The SOAK Cycle
should always be followed by a
Wash Cycle.
Important: See additional care
information in your “Laundry
Guide!’
‘To start soak or pre-wash with agitation, the Control Knob
must point to a number in the SOAK Cycle.
Liquid bleach dispenser
Always measure bleach. Do not
guess. Never use more than 1 cup
(250 ml) for a full load. Use less with
lower water level settings. Follow
directions on bottle for safe use. Use
a cup with a pouring spout to avoid
spilling.
1
1.
2. Load the washer first.
Pour measured bleach carefully
into dispenser, DO NOT let bleach
splash, drip or run down into the
washer basket. Undiluted bleach
will damage any fabric it touches.
Start the washer. Bleach will be
diluted automatically during the
wash part of the cycle.
For more information on bleaching, see your “Laundry Guide!’
13

Liquid fabric softener dispenser
1. Add detergent and load to the
basket.
2. Add liquid fabric softener to the
dispenser using the amount recom-
mended on the bottle.
3. Avoid dripping or spilling any fabric
softener on the load.
4. Dilute fabric softener with hot water.
Add enough hot water to fill the dis-
penser up to the opening.
5. Start the washer. Diluted fabric
softener will be added to the load
during the deep rinse portion of
the cycle. NOTE: Do not stop the
washer during this time. If you do,
the softener will mix with the remain-
ing soapy wash water, This will
cause stains. Do not put detergent
in the liquid fabric softener
dispenser.
6. If dispenser needs cleaning, flush
with hot water. NOTE: Do not wash
clothes with dispenser removed.
MAGIC CLEAN” lint filter
The lint filter in your washer cleans itself. Collected lint is
drained away with the wash and rinse water.
If your washer drains into a tub, remove any lint collected
in the drain or strainer.
14

Caring for your washer
WHEN NOT WASHING, keep both
water faucets turned off. This takes the
pressure off the water inlet valve and
hoses.
REMOVE SHARP OBJECTS such as SHARP OR HEAVY OBJECTS should
pins, buckles, etc., from clothes before never be put on or in the washer.
washing. Close metal zippers. Check pocket for bolts, nuts, tools, etc.
AFTER WASHING, use a soft dry cloth to
wipe the outside and inside dry. Leave
the lid up until the basket is dry. Wipe
up spills right away. Spills can dull or
damage the finish.
SOME PRETREATMENT PRODUCTS can
damage washer and dryer dials, con-
soles and finishes, Do not use these
products on or near your washer or
dryer.

Winterizing
Because some water stays in the washer, freezing
can cause a lot of damage. If your washer is
stored or moved during the cold weather...
“,:,;
i
1)
1. Shut off both water 2. Put a quart of R.V. 3. Set the washer for a
faucets. Disconnect or automobile type DRAIN and SPIN
and drain water antifreeze in the (see page 12). Let it
inlet hoses. basket. run for about 30
seconds to mix the
antifreeze and
water.
OH
- through a com-
To use the washer again...
plete cycle with
one cup of deter-
1. Flush water pipes and hoses. gent to clean out
2. Connect hoses to the washer the antifreeze.
3. Turn on the water faucets,
16

If you need service or assistance,
we suggest you follow these five steps:
1. Before cafe& for
assistance...
Performance problems often result
from little things you can find and fix
yourself without tools of any kind.
If your washer does not fill:
l Is the power supply cord plugged
into a live circuit with the proper
voltage?
l Have you checked your home’s
main fuses or circuit breaker box?
l Are the water supply hoses kinked?
l Is the Cycle Control Knob set and
pulled out?
If your washer does not spin:
l Is the lid closed?
l Is the power supply cord plugged
into a live circuit with the proper
voltage?
l Have you checked your home’s
main fuses or circuit breaker box?
If your washer stops during a cycle:
l Remember, the washer pauses
briefly at different times in each
cycle. These pauses are normal.
If your washer fills and drains
without running:
l Make sure that the Cycle Control
Knob is pointing to a number in the
cycle.
Make sure the drain hose is higher
than the water level in the washer.
If it isn’t:
l The washer may seem to be drain-
ing during wash and rinse cycles.
l Water can siphon out. (See “lnstalla-
tion Instructions:‘]
l Are both water faucets open?

2. If you need
assistance?..
Call Whirlpool COOL-LINE” serv-
Ice assistance telephone number.
Dial free from anywhere in the U.S.:
1-800-253-1301
and talk with one of our trained Con-
sultants The Consultant can instruct
you in how to obtain satisfactory
operation from your appliance or, if
service is necessary, recommend a
qualified service company in your
area.
3. If you need service?..
a/-
Whirlpool has a
Whid 01
lCdCE1
nationwide network
of franchised TECH-
CARE nService Com-
panies. TECH-CARE
service technicians
are trained to fulfill the product
warranty and provide after-warranty
service, anywhere in the United States.
Whirlpool Corporation for quality
parts. Look for this symbol of quality
whenever you need a replacement
part for your Whirlpool appliance. FSP
replacement parts will fit right and
work right, because they are made to
the same exacting specifications
used to build every new Whirlpool
appliance.
To locate TECH-CARE service in your
area, call our CCCL-LINE service assis- Xlf you must call or write, please pro-
tance telephone number (see Step2) or vide: model number, serial number,
look in your telephone directory Yellow date of purchase, and a complete
Pages under: description of the problem. This infor-
mation is needed in order to better
4. If you have a
problem?..
Call our COOL-LINE service as-
sistance telephone number (see Step
2) and talkwith oneof ourConsultants,
or if you prefer, write to:
Mr. Donald Skinner
Director of Customer Relations
Whirlpool Corporation
2000 M-63
Benton Harbor, Ml 49022
5. If you need FSP’”
replacement parts?..
FSP is a registered trademark of
18

Notes