Whirlpool Washer 3775 Quick start guide

PARTS &
SERVICEManual
AUTO SPARKLE
SAP MODEL NO DESCRIPTION
3775 AUTOSPARKLE-110V,APWH.W.PUMP(BARBA,CURAC

This document is only intended for qualified technicians who are aware of the respective safety regulations.
Revised on 07/01/2003 Subject to modification
Document No. WOI/WM/2003/001
CONTENTS
S No DESCRIPTION PAGE No
1 SPECIFICATIONS 3
2. AUTOSPRAKLE FEATURES 6
3. CONTROL & FUNCTIONS 6
4. WIRING DIAGRAM 10
5. PROGRAM TIMING 12
6. EXPLODED VIEWS 15
7. PARTS LIST 18
8. FAULT FINDING-GUIDE 20

This document is only intended for qualified technicians who are aware of the respective safety regulations.
Revised on 07/01/2003 Subject to modification
Document No. WOI/WM/2003/001
Specifications
1 .Model Description AUTOSPARKLE
2. Machine Type Top Loading fully Automatic Agitator wash
3. Capacity 5 Kg.
4. M/c Wt. 38 Kg.
5. M/c Dimension 570 mm (W) x 590 mm (B) x 1000 mm (H)
6. Cabinet Finish Pre painted Steel
7. No of programs 1 9
8. Program Select 4 LED’s - Normal, Speed, Heavy & delicate (Heavy double rinse)
9. Start/Pause Provided
10. Error Signal (Audio) Available
I 1. Wash Action Normal, Speedy, Heavy (65 SPM) Delicate (45 SPM)
12. Spin Speed 740 RPM (Max.)
13.Dispenser Bleach dispenser (Hose less type)
Blue dispensing (through Dispenser fitted to Agitator.
1 4. Lint filter Available (fitted to blue dispenser)
15. Motor 1/4 HP, 1400 RPM, PSC Type, single speed (input 575W)
16. Operating Voltage 110V 50Hz
17. Basket Polypropylene
18. Temp Permitted Max. 50"C
19. Water level switch Rotary continuous (4 indications Extra Low, Low, Medium, High)
20. Water volume (liters) Setting With Load W/o Load
Extra Low 25 27
Medium 50 54
High 65 70
Low 35 38
21. Water Saver By selection

This document is only intended for qualified technicians who are aware of the respective safety regulations.
Revised on 07/01/2003 Subject to modification
Document No. WOI/WM/2003/001

This document is only intended for qualified technicians who are aware of the respective safety regulations.
Revised on 07/01/2003 Subject to modification
Document No. WOI/WM/2003/001
AUTOSPARKLE - FEATURES :
?Spin Basket - P.P. Material
?Easy spin basket removal is possible
?Hose less bleach inlet system
?Single Pressure switch hose.
?LID switch control for Agitate/Spin operations.
(8 Bit controller)
?Tub ring mounting with out screws
A LOOK AT THE CONTROL PANEL...
The following are the knobs/switches available at the panel
1 Power ON/OFF Switch
2. Water level selector
3. Course Select
4. Program Select
5. Start/Pause Button
In addition to the above, 2 sets of 4 each LED indications are also provided to indicate the status of operations. Please refer
the annexure for schematic view of the Panel. POWER ON/OFF SWITCH

This document is only intended for qualified technicians who are aware of the respective safety regulations.
Revised on 07/01/2003 Subject to modification
Document No. WOI/WM/2003/001
This switch is basically a ON/OFF switch controlling the supply to the machine, by pressing this switch, the machine is
turned ON.
To Switch off the machine, press the switch again.
Machine operation stops automatically at the end of the cycle and this switch will still
remain in ON position Similar To ALPHA model and the user has to switch it OFF before removing the clothes from the
spin basket.
WATER LEVEL SELECTOR
This is similar to our existing Load Selector with the difference that the pressure switch mounted inside is "Constant Reset
Type".
PROGRAM SELECT BUTTON
This feature enables the user to select the various wash cycles viz., NORMAL, SPEEDY, DELICATE and HEAVY. The
selection is effected by pressing this Program Select and indicate by the glowing of the corresponding LED indicator in the
panel. The default setting is NORMAL cycle. Other cycles can be selected by pressing the Program Select button in the
following sequence.
CONTROL SETTING PROGRAM ACTIVATED
POWER SWITCH ON(Default) NORMAL
FIRST PRESS SPEEDY
SECOND PRESS DELICATE
THIRD PRESS HEAVY
If the user presses for the fourth time, the machine returns to default setting i.e., NORMAL cycle.

This document is only intended for qualified technicians who are aware of the respective safety regulations.
Revised on 07/01/2003 Subject to modification
Document No. WOI/WM/2003/001
COURSE SELECT
This feature enables the user to select the various combination of SOAK, WASH, RINSE and SPIN. The Selection is
effected by pressing this Course Select button and indicated by the glowing of the corresponding LED indicator in the
panel. The default setting is WASH, RINSE and SPIN i.e. whenever the Power Switch is switched ON, these 3 processes
will be selected by default and the corresponding LED lamps will glow. As the Course Select button is pressed further, the
other selections can be made in the following sequence:
COURSE SELECT PROGRAM
Power Switch ON(Default) WASH RINSE SPIN
First Press SOAK WASH RINSE SPIN
Second Press WASH
Third Press WASH RINSE
Fourth Press RINSE SPIN
Fifth Press SPIN
If the user presses for the sixth time, the machine returns to default setting i.e., WASH, RINSE and SPIN cycle. Whenever
Speedy Program is selected, the course is selected by default, as WASH, RINSE and SPIN and hence no other
combinations are possible.
START/PAUSE BUTTON
This button is used to start or pause the cycle. Once all the settings are set, the user has to press this button to commence
the cycle. Similarly, this button can also be pressed while the machine is operating to pause the operation. This facility may
be used in case the Customer wants to add some more detergent or clothes in the middle of the cycle. Whenever the
operation is paused, the user will get a continuous beep sound to indicate that the machine has been 'paused'. To restart the
cycle, the button has to be pressed again.
LED INDICATORS
This is 2 sets of 4 each LED indicators provided in the control panel. This helps to indicate the status of the cycle in
progress.
WASH PROGAMME
From the above details on the various controls available in this model, it is clear that the user can choose the combination
of various course (SOAK, WASH, RINSE, and SPIN) and Programmer (NORMAL, SPEEDY, DELICATE, and
HEAVY). The possible combinations for say a NORMAL cycle are
1. WASH RINSE & SPIN
2. SOAK WASH RINSE &SPIN
3. WASH ONLY
4. WASH AND RINSE
5. RINSE AND SPIN
6. SPIN ONLY
Thus each of NORMAL, DELICATE & HEAVY cycle can give 6 possible combinations resulting in 18 cycles. In case of
SPEEDY cycle, the course options are preset as WASH, RINSE and SPIN and hence no other combinations can be chosen.
Thus, a total combination of 18 plus 1 SPEEDY cycle i.e. a total of 19 cycles is possible in this model.

This document is only intended for qualified technicians who are aware of the respective safety regulations.
Revised on 07/01/2003 Subject to modification
Document No. WOI/WM/2003/001
The timing sequences of this individual cycle are enclosed for your ready reference.
OPERATING INSTRUCTIONS:
1. Add detergent and load the clothes as usual.
2. Connect the Fill Hose and Power cord to the appropriate points. 3. Place the Drain Hose on the ground.
4. Switch on the machine. Set the Water level and Water inlet Selector (as applicable) to the desired settings.
5. Select the appropriate Course and Program.
6. Press the Start button to commence the operation.
7. At the completion of the cycle, the user will get a intermittent beep sound lasting for 20 seconds. STATUS
INDICATORS
As you are aware, LED indicators are provided in the Control Panel to indicate the status of the wash cycle. Whenever the
Program and Course is selected, the corresponding LED indicators will glow. Once the operation is commenced, the LED
corresponding to the first operation (Soak or Wash or Rinse or Spin) will blink indicating that the particular process is on.
Once the process is completed, the corresponding LED will go off and the LED corresponding to the next operation will
start blinking. Thus by a look at the Control Panel, the user can come to know of the process in progress (indicated by the
blinking LED) and the pending processes for the completion (indicated by glowing LED/s) of the cycle. Let us take an
example of a cycle wherein WASH, RINSE & SPIN is selected. The sequence of LED display will be as follows:
1.At the time of setting 2.During Washing 3.At the time of setting 4.During Washing
SPECIAL FEATURES IN ET MODES:
• DOUBLE RINSE FACILITY IN HEAVY WASH PROGRAME
Whenever the user chooses Heavy Program, after washing the clothes the machine takes in water twice for rinsing. This is
to increase the effectiveness of rinsing. However, it is worth noting here that no SIS and Spin is provided before the first
rinse. This has been thoughtfully designed such that the liquid blue from the dispenser gets dispensed only after the second
rinsing is completed.
• DYNAMIC SOAK:
Whenever the user selects SOAK in the wash cycle, during this soaking period the machine alternatively stirs (agitates) for
sometime and soaks for sometime. This aids better mixing of detergent in the water thereby aiding dirt removal. The total
OFF SOAK
ON WASH
ON RINSE
ON SPIN
OFF SOAK
BLINK WASH
ON RINSE
ON RINSE
OFF SOAK
ON WASH
BLINK RINSE
ON SPIN
OFF SOAK
OFF WASH
OFF SPIN
BLINK SPIN

This document is only intended for qualified technicians who are aware of the respective safety regulations.
Revised on 07/01/2003 Subject to modification
Document No. WOI/WM/2003/001
soaking time is 32 minutes with the machine agitating for the first 2 minutes. This is followed by 20 seconds agitation and
3 minutes soak cycle for the remaining 30 minutes.
*ERROR SIGNALS:
During operation, if any malfunction or misoperation occurs, the timer automatically indicates the same to he user through
an appropriate error signal. The various possible errors during operation and the type of error signal along with the
remedies are listed in the table as below
CAUSE SIGNAL TYPE FREQUENCY REMEDY
Lid is open during the spin 1”BEEP 1” OFF EVERY 5 SECONDS CLOSE THE LID
Improper drain /High drain
time ½”BEEP ½”OFF
½”BEEP 3 ½” OFF EVERY 5 SECONDS TILL THE PR. SWITCH
RESETS
REMOVE DRAIN
RESTRICTIONS
Course select button is
pressed down whenever
speedy program is selected
1”BEEP 1”OFF 1”BEEP
1”OFF 1”BEEP 1”OFF FOR EVRY PRESS OF COURSE SELECT KEY NO OPTIONS AVAILABLE IN
SPEEDY PROGRAM
DYMANIC SOAK
Whenever the user SOAK the wash cycle during this soaking period the machine as alternatively stirs (agitates) for some
time and soaks for some time. This aids better mixing of detergent in water hereby aiding dirt removal. The total soaking
time is 32 minutes with the machine agitating for the first two minutes. This is followed by 20 seconds agitation and 3
minutes soak cycle for the reaming 30 minutes.
SERVICE/DEMO ROUTINE :
To enable the CSE s in the field to test the device for its normal operations, a service routine is provided in these ET
models. to activate this, switch on the machine and press all the feather touch buttons i.e., course select, program select,
start/pause key and the cancel key simultaneously. Then release the cancel button. This will lead the machine o service
routine wherein the following operations are performed in sequence
1. All the 8 LED’s will be lighted.
2. Valve inlet will be switched on for 10 seconds.
3. Normal Agitation for 40 Sec.
4. Slow Agitation for 40 Sec.
5. Drain will be on for 20 Sec.
6. Spin will be on for 8 seconds.
7. EOC Buzzer will be for 15 seconds.

This document is only intended for qualified technicians who are aware of the respective safety regulations.
Revised on 07/01/2003 Subject to modification
Document No. WOI/WM/2003/001
Wiring Diagram