Whispbar K312W User manual

K312W
Fitting Kit
EN Fitting Instructions for Basic Carrier
x 2 x 2 x 4
Revision No: 5E 1

Fitting Kit K312W
MAX kgs (lbs)
W/P WHD
Mazda
2, 5dr Hatch 02-06 EU 50 kgs (110 lbs) 50 kgs (110 lbs)
2, 5dr Hatch 02-06 CN 50 kgs (110 lbs) 50 kgs (110 lbs)
2, 5dr Hatch Dec 02-Aug 07 AU 50 kgs (110 lbs) 50 kgs (110 lbs)
2, 5dr Hatch Dec 02-Aug 07 NZ 50 kgs (110 lbs) 50 kgs (110 lbs)
Demio, 5dr Hatch Dec 02-Aug 07 NZ 50 kgs (110 lbs) 50 kgs (110 lbs)
2

Fitting Kit K312W
X
A B C 1 2 3
2, 5dr Hatch 02-06 (EU) -180mm 450mm - 795mm 785mm -
-7 -1/16ths" 17 11/16ths" - 31 5/16ths" 30 7/8ths" -
2, 5dr Hatch 02-06 (CN) -180mm 450mm - 795mm 785mm -
-7 -1/16ths" 17 11/16ths" - 31 5/16ths" 30 7/8ths" -
2, 5dr Hatch Dec 02-Aug 07 (AU) -180mm 450mm - 795mm 785mm -
-7 -1/16ths" 17 11/16ths" - 31 5/16ths" 30 7/8ths" -
2, 5dr Hatch Dec 02-Aug 07 (NZ) -180mm 450mm - 795mm 785mm -
-7 -1/16ths" 17 11/16ths" - 31 5/16ths" 30 7/8ths" -
Demio, 5dr Hatch Dec 02-Aug 07 (NZ) -180mm 450mm - 795mm 785mm -
-7 -1/16ths" 17 11/16ths" - 31 5/16ths" 30 7/8ths" -
3

Fitting Kit EN
K312W
First Time Installation
●Remove parts from inside the package and
check. Contact your dealer if any parts are
missing or damaged.
●This kit fits type A, B, C and D.
●These instructions show type A crossbar
fitted. They also apply to type B, C and D.
NOTE: Clamp images in these instructions may
not be representative of the clamps in this kit
4

Fitting Kit EN
K312W
●Use keys to remove covers.
●Use hex screwdriver to reverse adjusting
screw 10 turns.
●Press adjusting screw and pull crossbar
legs out. Refer to the crossbar instructions
for crossbar adjustment method.
●Ensure each end of the crossbar is
adjusted equally.
5

Fitting Kit EN
K312W
●Remove locking screw.
●Apply protective strip as shown.
Trim if required.
●Letters refer to the part numbers stamped
on clamps.
●Clamp Part Number:
A = 461A
B = 462A
6

Fitting Kit EN
K312W
●Attach clamp to each leg. NOTE; clamps
may have labels showing their positions on
the vehicle (For example; "Front Right").
●Refit locking screw so that it goes through
the hole in the clamp. Do not begin to
tighten the locking screw.
●Fit rubber pad (supplied with crossbar) to
foot.
7

Fitting Kit EN
K312W
●Make sure the pad fits into the holes
underneath the foot.
Fitment
●Place crossbar on vehicle. Minimum
recommended spacing between the bars is
700mm (27 1/2") (unless otherwise stated).
●Please check the front of this manual for
information relating specifically to your
vehicle.
●Adjust the legs on the crossbar so that they
are positioned equally from the ends of the
crossbar, and the clamps engage firmly on
the body work of the vehicle.
8

Fitting Kit EN
K312W
●Tighten adjusting screw to 5 Nm (3.7 ft lb)
hand tight.
●Tighten locking screw on both legs evenly.
●Check crossbar is securely attached to the
vehicle.
9

Fitting Kit EN
K312W
●Use keys to fit and lock covers
CAUTION: Recheck all fasteners immediately after
a load is applied to the crossbars.
Regularly check screws are tight.
10