Whitewood Industries T-42DPT User manual

ITEM NO.: T-42DPT AND T-30P OR T-27B OR T-11B
ISSUED JUN 25, 2018
Printed in Vietnam
- 1 -
ASSEMBLY INSTRUCTIONS
T-42DPT AND T-30P
T-42DPT AND T-27B T-42DPT AND T-11B
Description
Item No.
: 42 IN DROPLEAF TOP ONLY
:
T-42DPT AND T-30P OR T-27B OR T-11B
(PACKED IN SEPARATE BOX)

ITEM NO.: T-42DPT AND T-30P OR T-27B OR T-11B
ISSUED JUN 25, 2018
Printed in Vietnam
- 2 -
BEFORE ASSEMBLY
Thank you for purchasing this quality product. This product has been designed for easy assembly
and constructed for durability. All parts were checked prior to packaging to insure quality. Prior to
beginning assembly, however, make sure all parts and hardware are included and free of obvious
defect. If a part is missing or defective, please contact the store where purchased. If hardware is
missing, or you need help with assembly, please call toll free 888-944-8396.
IMPORTANT NOTE:
-Place all wooden parts on a clean and smooth surface such as a rug or carpet to avoid the
parts from being scratched.
-Remove all wrapping material, including staples & packing straps before you start to
assemble.
-DO NOT tighten all screws, bolts until completely assembled.
-Keep all hardware parts out of reach of children.
WARNING:
-Long exposure to rubber or soft plastic may cause a chemical reaction and damage the
finish of your table. Protect the surface of the table with cloth if you are using any product
with rubber feet or base.

ITEM NO.: T-42DPT AND T-30P OR T-27B OR T-11B
ISSUED JUN 25, 2018
Printed in Vietnam
- 3 -
PART LIST
When unpacking, please be careful not to discard any parts with the packaging. Before continuing,
please make sure you have the following parts:
NO
Description
Qty
Sketch
NO
Description
Qty
Sketch
A
Top 1
B
Mounting
Plate
1
C
Wood slide 2
ART LIST PART LIST
HARDWARE LIST
When unpacking, please be careful not to discard any parts with the packaging. Before continuing,
please make sure you have all of the following hardware:
NO
Description
Qty
Sketch
NO
Description
Qty
Sketch
1
Bolt
(M6 x 45mm) 12
2
Small Flat washer
(F6.5 x 13mm)
4
3
Large Flat washer
(F6.5 x 19mm) 8
4
Lock Washer
(F6.5 x 11mm)
12
5
Allen key
(M4 x 30mm x 110mm
)
1

ITEM NO.: T-42DPT AND T-30P OR T-27B OR T-11B
ISSUED JUN 25, 2018
Printed in Vietnam
- 4 -
STEP 1
Attach the mounting plate (B) to the pedestal with bolts (1), and washers (2) and (4) as shown below.
Tighten with Allen key (5).

ITEM NO.: T-42DPT AND T-30P OR T-27B OR T-11B
ISSUED JUN 25, 2018
Printed in Vietnam
- 5 -
STEP 2
Carefully place the pedestal on the bottom side of the table top. Attach the top (A) to mounting
plate with bolts (1), and washers (4) and (3) as shown below. Tighten with Allen key (5).

ITEM NO.: T-42DPT AND T-30P OR T-27B OR T-11B
ISSUED JUN 25, 2018
Printed in Vietnam
- 6 -
STEP 3
Hold the drop leaf push and slide the wooden piece from underneath the table top. To lower the drop
leaf, carefully hold the drop leaf with one hand and slide the wooden piece from underneath the table
top towards the center of the top. Then, gently lower the leaf and place in the down position.