Whitewood Industries TV-34 User manual

ITEM NO.: TV-34
REVISED JAN 25, 2016
Printed in Vietnam
- 1 -
Description
Item No
: 48 IN TV STAND RTA
: TV-34
ASSEMBLY INSTRUCTIONS

ITEM NO.: TV-34
REVISED JAN 25, 2016
Printed in Vietnam
- 2 -
Thank you for purchasing this quality product. This product has been designed for easy assembly
and constructed for durability. All parts were checked prior to packaging to insure quality. Prior to
beginning assembly, however, make sure all parts and hardware are included and free of obvious
defect. If a part is missing or defective, please contact the store where purchased. If hardware is
missing, or you need help with assembly, please call toll free 888-944-8396.
IMPORTANT NOTE:
-Place all wooden parts on a clean and smooth surface such as a rug or carpet to avoid the
parts from being scratched.
-Remove all wrapping material, including staples & packing straps before you start to
assemble.
-DO NOT tighten all screws and bolts until completely assembled.
-Keep all hardware parts out of reach of children.
WARNING:
Long exposure to rubber or soft plastic may cause a chemical reaction and damage the
finish of your product. Protect the surface of the product with cloth if you are using any
product with rubber feet or base.
BEFORE ASSEMBLY
ASSEMBLY TOOLS REQUIRED
NOT INCLUDED

ITEM NO.: TV-34
REVISED JAN 25, 2016
Printed in Vietnam
- 3 -
PART LIST
When unpacking, please be careful not to discard any parts with the packaging. Before continuing,
please make sure you have the following parts:
NO
Description
Qty
Sketch
NO
Description
Qty
Sketch
A
Top
1
F
Side panel
(L-R)
2
B
Bottom
panel
1
G
Vertical panel
(L-R)
2
C
Center
shelf
2
H
Side shelf
2
D
Door (L-R)
2
I
Center back
panel (L-R)
2
E
Glass
2
J
Side back
panel
2
K
H - Connector
1

ITEM NO.: TV-34
REVISED JAN 25, 2016
Printed in Vietnam
- 4 -
HARDWARE LIST
When unpacking, please be careful not to discard any parts with the packaging. Before continuing,
please make sure you have all of the following hardware:
NO
Description
Qty
Sketch
NO
Description
Qty
Sketch
1
Bolt
(M6x35mm)
16
9
Short pan head
screw
(M3x15mm)
10
2
Spring washer
(6.5x13mm)
16
10
Screw
(M3x15mm)
22
3
Flat Washer
(6.5x19mm)
16
11
Magnet
2
4
Wooden knob
(38x30mm)
2
12
Shelf support
bracket
16
5
Long pan head screw
*Metal knob: (M4x22mm)
*Wooden knob: (M4x25mm)
2
13
Steel band
1
6
Door pin
(5.2/13x1.2mm)
(7x10mm)
4
14
Warning label
2
7
Long screw
(M4x30mm)
1
15
Medium screw
(M4x25mm)
2
8
Allen key
(M4x80mm)
1
METAL KNOB
(30x30mm)
GOES WITH
FINISHED ITEM
ONLY.
2

ITEM NO.: TV-34
REVISED JAN 25, 2016
Printed in Vietnam
- 5 -
STEP 1
Attach glass (E) to back of doors (D), and lock it.
Attach knobs (4) to doors (D) with pan head screws (5) as shown below. Tighten with a screwdriver.
STEP 2
Attach panels (G) to top (A) and bottom panel (B) with bolts (1), and washers (2) and (3) as shown
below. Tighten with Allen key (8).
Attach doors (D) (from STEP 1) to top (A) and bottom (B) with door pins (6).
Attach magnets (11) to top (A) with screws (10) as shown below. Tighten with a screwdriver.

ITEM NO.: TV-34
REVISED JAN 25, 2016
Printed in Vietnam
- 6 -
STEP 3
Attach side panels (F) to the unit with bolts (1), and washers (2) and (3) as shown below. Tighten with
Allen key (8).
STEP 4
Slide center back panels (I) into groove of H-connector (K). Then slide center back panels (I) into
groove of panels (F). Attach center back panels (I) to bottom (B) with screws (9). Attach H-connecter
to top (A) and bottom (B) with screws (15) as shown below. Tighten with a screwdriver.
Slide side back panels (J) into grooves of panels (G) and (F). Then attach back panels to bottom (B)
with pan head screws (9) as shown below. Tighten with a screwdriver.
TEP 4

ITEM NO.: TV-34
REVISED JAN 25, 2016
Printed in Vietnam
- 7 -
STEP 5 (FINISH)
Stick Warning labels (14) on the back side of doors before use.
Insert brackets (12) into the unit as shown below. Place shelves (C) and (H) on the brackets and
attach with screws (10). Tighten with a screwdriver.
Attach steel band (13) to the unit with screws (10). Then attach the steel band to a wall with screw (7)
as shown below (to secure the product and prevent tipping). Tighten with a screwdriver.