Whittier Wood Furniture 3841DUETa User manual

P.O. Box 2827
Eugene, OR 97402 USA
Production Code:
VN 02/23
Model #
3841DUETa
Addison King
Bookcase Storage
Bed
DUET finish
Assembly Instructions
IMPORTANT NOTES:
•Wood can be susceptible to changing color over time when exposed to
strong sunlight. Use window shades, drapes or blinds to protect your
furniture. To help the surface age evenly and avoid dark and light
spots, periodically move items to expose the entire surface to an even
amount of light so it may develop a uniform patina.
•For normal household use only. Not recommended for commercial use.
•Remove items before you move this unit.
•Do not overload the concealed storage areas.
•Use care when operating the soft-close sliding doors. Minimal effort is
required for doors to perform.
•This assembly requires two people.
WARNING
Drilling, sawing, sanding or machining wood products can expose you to
wood dust, a substance known to the state of California to cause cancer.
Avoid inhaling wood dust or use a dust mask or other safeguards for
personal protection.
For more information go to: www.p65warnings.ca.gov/wood
This product can expose you to chemicals, including formaldehyde,
which are known to the State of California to cause cancer.
For more information go to: www.p65warnings.ca.gov/furniture
DUAL PORT USB WALL CHARGER: CAUTION: Changes or modifications not
approved by the party responsible for compliance could void user’s authority to
operate the equipment .
NOTE: This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the use is encouraged to
try to correct the interference by one or more of the following measures:
•Reorient or relocate the receiving antenna.
•Increase the separation between the equipment and receiver
•Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
DESIGN SUBJECT TO CHANGE WITHOUT NOTICE.
CUSTOMER SERVICE
If you ever have questions about your furniture, please do not hesitate to contact us. In the unlikely event you need a
replacement part; we can make those parts available through an authorized Whittier Wood Furniture dealer. If you
cannot order replacement parts through your dealer, please contact our customer service department.
Hours: Our friendly customer service staff can be reached:
Monday-Friday 8:00 a.m. to 5:00 p.m. (Pacific Time).
You may leave a message 24 hours a day, seven days a week.
Customer Service: 800-653-3336 • Outside the U.S.: 541-687-0213
Fax: [phone]• Email: [email protected]
Thank you for allowing us to help you furnish your
home. We are certain you will be delighted with
your new furniture for many years to come.

3841DUETa Addison King Bookcase Storage Bed
Parts List
3841DUETa — Page 2 — 02/23
Please identify the parts and check that quantities received match those on this list.
If you need to replace a part, refer to the following letter and part name.
3842DUETa Headboard Kit (x1)
Part
Description
Quantity
Aa
Headboard Assembly
1
K
#8 x 7/8" Black Lo-Profile Screw (inserted)
18
M
#8 x 1-5/8" Black Screw (inserted)
4
Y
5/16" x 14mm Insert Nut (inserted)
4
YA
#8 x 2-1/4" Black Screw (inserted)
4
YB
60mm Long Strap (installed)
4
YC
#6 x 1/2" Undercut Screw AB (inserted)
8
YD
Washer (installed)
8
YE
#6 x 3/4" Flat Head Screw (inserted)
16
YF
#6 x 5/8" Undercut Screw ZN (inserted)
16
ZH
Short Aluminum Track Rail (installed)
1
ZI
Long Aluminum Track Rail (installed)
1
ZJ
Roller (installed)
8
ZK
Soft Close Damper (installed)
2
ZL
#8 x 5/8" Pan Head Screw (inserted)
8
ZM
#8 x 1-3/8" Lo-Profile Screw (inserted)
24
ZO
Power Supply (attached)
1
ZP
A/C Dual Port (attached)
1
ZQ
Corner Brace (attached)
2
ZR
Large Adjustable Glide (installed)
2
ZS
Tack Glide (attached)
4
ZT
Top Assembly (attached)
1
ZUa
Left Door (installed)
1
ZVa
Right Door (installed)
1

3841DUETa Addison King Bookcase Storage Bed
Parts List
3841DUETa — Page 3 — 02/23
Part
Description
Quantity
ZW
False Bottom (installed)
2
ZX
#6 x 5/8" Philtruss Screw (inserted)
2
ZY
#8 x 1-1/4" Pan Head Screw (inserted)
2

3841DUETa Addison King Bookcase Storage Bed
Parts List
3841DUETa — Page 4 — 02/23
3843DUET Footboard Kit (x1)
Part
Description
Quantity
B
Footboard Assembly
1
C
Center Deckboard
1
L
#8 x 1-1/4" Black Screw
36
Y
5/16" x 14mm Insert Nut (inserted)
4
ZE
5/16" x 2-1/4" Hex Bolt
6
ZF
5/16" x 35mm Hex Bolt
18
ZG
1/4" Flat Washer
24

3841DUETa Addison King Bookcase Storage Bed
Parts List
3841DUETa — Page 5 — 02/23
2019DUET
Queen/King Pedestal Kit (x2)
Part
Description
Quantity
D
Pedestal
1
E
Drawer Box (assembled)
3
F
Drawer Face (attached)
3
G
Left/Right Center Deckboard
1
H
20" Drawer Slides (installed)
3 sets
I
#6 x 3/4" Philtruss Screw (inserted)
18
J
#6 x 1/2" Philtruss Screw (inserted)
18
K
#8 x 7/8" Black Lo-Profile Screw (inserted)
18
L
#8 x 1-1/4" Black Screw (inserted)
8
M
#8 x 1-5/8" Black Screw (inserted)
24
N
#8 x 1-5/8" Machine Screw Tuscan (installed)
6
O
5/32" x 10mm Insert Nut (inserted)
6
P
Black Walnut Pull (attached)
3

3841DUETa Addison King Bookcase Storage Bed
Parts List
3841DUETa — Page 6 — 02/23
2024DUET
Addison King Base Kit (x1)
Part
Description
Quantity
Q
Mitered End Support
1
R
Square End Support
2
S
Left Support
1
T
Right Support
1
V
King Trestle Rail (31-1/4")
4
W
#8 x 1-3/4" Pan Head Screw (inserted)
12
X
#10 x 3/4" Pan Head Screw (inserted)
16
Y
5/16" x 14mm Insert Nut (inserted)
18
ZA
Wood Dowel (inserted)
12
ZB
Foot Bracket (attached)
4
ZC
Adjustable Glide (installed)
4

3841DUETa Addison King Bookcase Storage Bed
Assembly Instructions
This assembly requires two people.
3841DUETa — Page 7 — 02/23
Tools Required: Slotted screwdriver, Phillips screwdriver, 1/2" open end or box end wrench.
1. Lay out and identify the parts from the king (#2024) Base Kit. Set aside part Trestle Rail (V) for
use later in the assembly process. Use the notch and dowels on Square End Support (R) and
Mitered End Support (Q) as a guide attach to the Right Support (T) using the Hex Bolts (ZE) and
Washers (ZG) from the Headboard/Footboard Kit. See Figures 1 and 1a.
2. Attach the assembly to the Left Support (S) Using Hex Bolts (ZE) and Washers (ZG). See
Figures 2 and 2a. Identify the Headboard end of the assembly and place near the final bed
location. See drawing below.
Fig. 2
S
R
R
ZG
ZE
x 3
x 3
Q
Footboard
Headboard
Fig. 2a
ZG
ZE
Fig. 1
R
R
T
ZG
ZE
x 3
x 3
Fig. 1a
ZG
ZE
Q

3841DUETa Addison King Bookcase Storage Bed
Assembly Instructions
This assembly requires two people.
3841DUETa — Page 8 — 02/23
3. Place each pedestal (D) on top of the base kit against the side of and between the locater
blocks of the Base Kit. See Figure 3.
Fig. 3
D
Locater blocks
Locater blocks
Headboard end of Base
has leveler outside the
crosspiece

3841DUETa Addison King Bookcase Storage Bed
Assembly Instructions
This assembly requires two people.
3841DUETa — Page 9 — 02/23
4. Open the drawers and attach the pedestal to the base using Hex Bolts (ZF) and Washers (ZG)
only finger tight. See Figures 4 and 4a.
Fig. 4
Fig. 4a
(Notched Deckboards removed for illustration purposes)
ZG
ZF
ZG
ZF
x 10
x 10

3841DUETa Addison King Bookcase Storage Bed
Assembly Instructions
This assembly requires two people.
3841DUETa — Page 10 — 02/23
5. NOTE: When attaching the Footboard (B) to the Pedestal/Base assembly attach it at the end of
the Base with the leveler behind the crosspiece.
There are two options to attach the Footboard (B) to the Pedestal Assembly. Option a) Release
the two drawers (E) at the end of the assembly as shown in Fig. 5a. Open the Drawers (E) until
the back edge of the drawer is even with the front of the Pedestal. Reach under the attached
deckboard from the backside of the pedestal and insert Bolts (ZF) and Washers (ZG) into the
Footboard (B). Push the drawers closed. Option b) remove the two end drawers (E) completely.
Insert the bolts and washers into the Footboard and reinstall the drawers. See Fig. 5b, 5c.
Fig. 5c
ZG
ZF
x 4
x 4
Fig. 5b
ZG
ZF
Option 5b shown in illustration
Fig. 5
Drawer Release Lever
Fig. 5a
Headboard end of Base
has leveler outside the
crosspiece
B