Whittier Wood Furniture McKenzie 2402AFGACb User manual

P.O. Box 2827
Eugene, OR 97402 USA
Production Code:
VN 07/13
Model #
2402AFGACb;
2402AFCAFb
McKenzie
File Cabinet
AFGAC = Glazed Antique Cherry finish
AFCAF = Caffè finish
Assembly Instructions
Congratulations!
This fine piece of furniture will make a gorgeous addition to
your home. For the best results, read the Assembly
Instructions before you begin your project.
IMPORTANT NOTES:
For normal household use only. Not recommended for commercial use.
Use a protective pad when you use the top of this piece as a writing
surface.
Do not climb, sit or stand on this piece of furniture.
Do not overload the drawers.
Unload items before you move this unit.
Before you load or move this unit, tighten all screws and supports.
Before you begin your project, completely read the Assembly
Instructions.
Store this item: 1- in its box; 2- in a dry place; 3- in temperatures that
range from 40°F to 90°F (not on a cold and possibly damp cement
floor).
Periodically inspect your furniture for any loose glue joints, screws or
any other problem that might affect the stability of your furniture.
Tighten or repair as needed.
WARNING
Serious or fatal crushing injuries can occur from furniture tip-over. Use of
tip-over restraints may only reduce but not eliminate the risk of tip-over.
To help prevent tip-over:
Place heaviest items in the bottom drawers.
Unless specifically designed to accommodate, do not set TVs or other
heavy objects on top of this product.
Never allow children to climb or hang on drawers, doors or shelves.
Never open more than one drawer at a time.
Warning: At least one tipping restraint kit was included with your piece of
Whittier Wood Furniture. When you receive your furniture, be sure to find
and properly install the tipping restraint(s). If you cannot locate the
restraint(s), please contact us immediately for replacement.
Notice to California Customers
California Prop 65 requires consumer goods to be labeled if any one of
850+ different chemicals or substances, including wood dust, is present
even in trace amounts. Drilling, sawing, sanding or machining wood
products generates wood dust, a substance known to the State of
California to cause cancer. Warning: This product contains a chemical
or substance known to the State of California to cause cancer, birth
defects or other reproductive harm. California Health and Safety Code
Section 25249.6
DESIGN SUBJECT TO CHANGE WITHOUT NOTICE.
CALL US FIRST! Do not return this item to the store
Service Policy: We will replace any part that is defective,
missing or damaged during assembly. For a replacement
part, directly contact Whittier Wood Products customer
service department by phone, fax, mail or email.
Hours: Our friendly customer service staff can be reached
Monday-Friday 7:00 a.m. to 5:00 p.m. (Pacific Time). You
may leave a message 24 hours a day, seven days a week.
To Order: Provide the finish and furniture model number
(upper portion of this page), the part letter, production
code, quantity needed, reason for replacement and your
full name, address and telephone number.
Parts ship from our Eugene, Oregon factory within one or
two business days from the time we receive your request.
Please allow five to ten business days for delivery.
800-653-3336 •Outside the U.S. or Canada: 541-687-0213 • Fax: [phone]
www.whittierwood.com • P.O. Box 2827 • Eugene, Oregon 97402, U.S.A.

2402AFGACb; 2402AFCAFb McKenzie File Cabinet
Parts List
2402AFGACb_2402AFCAFb —Page 2 —07/13
Please identify the parts and check that quantities received match those on this list.
If you need to replace a part, refer to the following letter and part name.
Part
Description
Quantity
Aa
Case Assembly
1
C
Lower Drawer (inserted)
1
D
Upper Drawer Face (installed)
1
E
Lower Drawer Face (installed)
1
F
Lock (attached)
1
G
#6 x 5/8" Philtruss Screw (inserted)
2
H
Drawer Slides (pre-installed sets)
2
I
#6 x 3/4" Philtruss Screw (inserted)
20
J
#6 x 1/2" Philtruss Screw (inserted)
16
K
Knob (attached)
2
L
#8 x 1-1/2" Machine Screw (installed)
2
M
Plastic File Rail (attached)
4
N
Aluminum File Rail
4
O S
#8 x 7/8" Lo-Profile Screw (inserted)
8
P T
#8 x 1-1/4" Pan Head Screw (inserted)
2
S Y
Small Adjustable Glide (installed)
4
T
Upper Drawer (inserted)
1
U
Insert Nut (inserted)
4
V
#8 x 1-3/8" Lo-Profile Screw (inserted)
7
TR
Furniture Tipping Restraint
1 set

2402AFGACb; 2402AFCAFb McKenzie File Cabinet
Assembly Instructions
2402AFGACb_2402AFCAFb —Page 3 —07/13
Tool Required: Phillips Screwdriver
1. Store your letter-sized hanging folders either parallel or perpendicular to the front of the drawer.
Legal-sized folders must hang perpendicularly.
To hang your files perpendicularly, remove the Plastic File Rails (M). See Figures 1 and 1a.
There are slots on the sides of the drawers. Insert an Aluminum File Rail (N) into the slots
nearest to the Drawer Face (D or E). Insert another Aluminum File Rail (N) into the second set
of notches for letter-sized folders or the third set of notches to hang legal-sized folders.
See Figures 1b and 1c.
(For Letter File Size)
M
M
Fig. 1
Fig. 1a
(For Legal File Size)
N
N
Fig. 1b
Fig. 1c

2402AFGACb; 2402AFCAFb McKenzie File Cabinet
Assembly Instructions
2402AFGACb_2402AFCAFb —Page 4 —07/13
2. Position the unit at the desired location. Adjustable glides (S) are attached to the bottoms of the
legs. Rotate the glides until the unit stands level. See Figure 2.
3. Tipping restraint: Locate a stud in the wall behind the unit. Attach a Clip (T1) to the wall stud
with two #8 x 2" Black Screws (T3). See Figure 3a. Attach a second clip to the unit with two
#6 x 5/8" Philtruss Screws (T5). See Figure 3b. Connect the two clips with the Nylon Restraint
Strap (T2). Pull the Nylon Restraint Strap (T2) tight so there is no slack. See Figures 3c and 3d.
If you cannot locate a stud, purchase the proper wall attachment hardware for your type of wall
and secure the unit.
4. Use a protective pad when you use the top of this piece as a writing surface.
5. Keys are located in the tipping restraint bag.
Fig. 3a
T1
T3
Pull tight
Fig. 3d
T1
T2
T5
Fig. 3c
Pull the Nylon Restraint
Strap (T2) tight
so there is no slack.
T3
T5
T1
Fig. 3b
Fig. 2
S
S