Whittier Wood Furniture 1452AFGSP User manual

P.O. Box 2827
Eugene, OR 97402 USA
Outside U.S. or Canada: 541- 687- 0213Outside U.S. or Canada: 541- 687- 0213
800-653-3336800-653-3336
Fax: [phone] • Fax: [phone] • wwwwww.whittie.whittierrwood.comwood.com
Mail: P.O. Box 2827 • Eugene, Oregon 97402, U.S.AMail: P.O. Box 2827 • Eugene, Oregon 97402, U.S.A
For normal household use only.
recommended for commercial use.
Congratulations!
Production Code:
Assembly Instructions
Model #
Pacific King
Storage Bed
Glazed Spice finish
1452AFGSP
Service Policy: We will replace parts
which are defective, missing or damaged.
Please contact Whittier Wood Products
customer service department directly (by
phone, fax, mail or E-mail) for replacement
parts.
Hours: Our friendly customer service staff
can be reached Monday-Friday 7:00 a.m. to
5:00 p.m. (Pacific Time). A message can be
left 24 hours a day, 7 days a week.
To Order: Provide the complete furniture
model number, part letter, production code,
quantity needed, reason for replacement
and your full name and address along with
a telephone number in case we need to
contact you.
Parts ship from our Eugene, Oregon factory
within 1 or 2 business days from the time
we receive the request. Please allow 5-10
business days for delivery.
This fine piece of furniture will make a gorgeous
addition to your home. For the best results, start
by reading the Assembly Instructions before you
begin your project.
Unload items from this unit prior to moving.
Before
Do not overload the drawers in this unit.
loading or moving this unit, check all screws
and supports for tightness.
Completely read the Assembly Instructions
before you begin your project.
Store the item: 1) in its box; 2) in a dry place;
3) in temperatures that range from 40° to 90°
(not on a cold and possibly damp cement floor).
Periodically inspect your furniture for any loose
glue joints, screws or any other problem that might
affect the stability of your piece. Tighten or repair
as needed.
This Assembly requires two people.
DESIGN SUBJECT TO CHANGE WITHOUT NOTICE.
07/09VN

1452AFGSP Pacific King Storage Bed — Parts List
1455AFGSP (x1)
1453AFGSP (x2)
Page 2 — 1452AFGSP — 07/09
D — 5/16" x 2¼" Hex Bolt
— Qty. 8
Q — #6 x 1¼" Black Pan
Head Screw — Qty. 8 (inserted)
K — Angle Bracket
— Qty. 2 (attached)
E — 5/16" Washer
— Qty. 8
H — 1/4" Washer
— Qty. 12
N — Pedestal Kit
— Qty.1
A — Headboard — Qty.1
B — Footboard — Qty.1
O — Drawer Box
— Qty. 3 (assembled)
P — Drawer Face
— Qty. 3 (attached)
R — Drawer Slides
— Qty. 3 (installed sets)
C — Foot Assembly
— Qty. 6
X — Top Cap
— Qty. 1 (attached)
M — Adjustable Glide
— Qty. 6 (installed)
U — Hanger Bolt
— Qty. 6 (inserted)
V — Insert Nut
— Qty. 8 (inserted)
S — Hex Wrench
— Qty. 1
I — Barrel Nut
— Qty. 2
J — 9.5mm x 25mm
Wood Dowel — Qty. 2
T — T-Nut
— Qty. 6 (inserted)
L — #6 x 3/4" Flat Head Screw
— Qty. 12 (6 inserted)
G — ¼" x 1¾" Hex Bolt
— Qty. 12
T — T-Nut
— Qty. 9 (inserted)
F — 1/4" x 80mm
Hex Bolt — Qty. 2
W — Top Cap
— Qty. 1 (attached)
Please identify the parts and check that quantities received match what is on this list.
If you need to replace a part, refer to the following letter and item name.

1452AFGSP Pacific King Storage Bed
Assembly Instructions
Page 3 — 1452AFGSP — 07/09
This Assembly Requires Two People
Remove the Drawers (O) from the Pedestal Kits (N). To remove the drawers, push up on the left
side of the Drawer Release Lever while pushing down on the right Drawer Release Lever.
See Figure 1b. Note where each drawer came from to ensure correct re-installation.
Positions are also marked on the backs of the drawers.
1.
Fig. 1
Fig. 1b
Drawer Release Lever
1/2" Wrench, 7/16" Wrench, Tape Measure, Padded Hammer or Rubber Mallet, Wood Glue
2.
Fig. 2
x 12
x 12
G
H
To protect your flooring and the surface of the unit, place the Pedestal Kits (N) face-down on top of
opened and unfolded 1453 cartons as shown in Figure 2. (When you join the pedestals, carpet fibers
can get caught in between the middle supports.) Place twelve washers (H) over twelve ¼" x 1¾"
Hex Bolts (G) and thread each through a predrilled hole and into a T-Nut in the middle supports
found on each pedestal. Finger tighten each bolt, making sure the pedestals line up with each other.
Afterwards, use a 7/16" wrench to securely tighten each bolt. See Figure 2..
HG
G
H
T
O
unfolded 1453 cartons
N
T
TTT
TOOLS REQUIRED: Hex Wrench (provided), Phillips Screwdriver, Slotted Screwdriver

3. Rotate the Adjustable Glides (M) so that the Foot Assemblies (C) are 4½" tall as shown in Figure 3a.
Attach the six Foot Assemblies (C) as shown in Figure 3.
4. This step requires two people to move the bed to its upright horizontal position.
Rotate the bed so the deck boards are face-up. DO NOT PLACE UNDUE PRESSURE ON THE
FOOT ASSEMBLIES. This may cause them to bend or break. See Figure 4.
5. Spread a thin film of glue in the dowel holes at one end of the Top Cap (X) of the bed. Insert two
dowels (J) and gently tap with a rubber mallet. Quickly wipe away any excess glue. See Figures
5 and 5a.
Fig. 3
Fig. 3a x 6
C
C
4½"
Page 4 — 1452AFGSP — 07/09
Fig. 5
Fig. 5a
x 2
J
J
JJ
M
Fig. 4
XX

Page 5 — 1452AFGSP — 07/09
Fig. 6
Fig. 6a Fig. 6b
x 4
x 4
D
E
DE
B
J
J
DE
B
J
J
Fig. 7
x 4
x 4
D
E
D
E
6. Position the Footboard (B) against the end of the pedestal assembly and insert the dowels into the
oval holes in the Top Cap (W). Place four Washers (E) over four 5/16" x 2¼" Hex Bolts (D) and
thread the washer/bolts through the pre-drilled holes in the Pedestal Assembly and into the Footboard.
Tighten the bolts with a 1/2" wrench. See Figures 6, 6a and 6b.
7. Position the Headboard (A) against the end of the pedestal assembly. Place four Washers (E) over
four 5/16" x 2¼" Hex Bolts (D) and thread the washer/bolts through the pre-drilled holes in the
Pedestal Assembly and into the Headboard. Tighten the bolts with a 1/2" wrench. See Figure 7.
W

Fig. 8
Fig. 8a
Fig. 8b
x 6
L
L
x 2
F
x 2
I
I
F
I
L
Page 6 — 1452AFGSP — 07/09
F
F
Fig. 9
Reinsert the six drawers, sleep well and enjoy!9.
K
KC
Secure the preattached Angle Brackets (K) on the Headboard to the Pedestal Assembly with six
#6 x ¾" Flat Head Screws (L). See Figures 8 and 8a. Insert one Barrel Nut (I) into the predrilled hole on
the bottom of the left pedestal rail. Using a slotted screwdriver, line up the hole in the Barrel Nut
to the hole in the Headboard. Insert one 1/4" x 80mm Hex Bolt (F) into the predrilled hole in the
Headboard and tighten with the provided Hex Wrench (S). Repeat for the right side. See Figures
8 and 8b.
If needed, adjust the six Foot Assemblies (C).
8.