Whittier Wood 2903AFGAC User manual

P.O. Box 2827
Eugene, OR 97402 USA
Outside U.S. or Canada: 541- 687- 0213Outside U.S. or Canada: 541- 687- 0213
800-653-3336800-653-3336
Fax: [phone] • Fax: [phone] • wwwwww.whittie.whittierrwood.comwood.com
Mail: P.O. Box 2827 • Eugene, Oregon 97402, U.S.AMail: P.O. Box 2827 • Eugene, Oregon 97402, U.S.A
For normal household use only.
recommended for commercial use.
Congratulations!
Production Code:
V N
Service Policy: We will replace parts
which are defective, missing or damaged.
Please contact Whittier Wood Products
customer service department directly (by
phone, fax, mail or E-mail) for replacement
parts.
Hours: Our friendly customer service staff
can be reached Monday-Friday 7:00 a.m. to
5:00 p.m. (Pacific Time). A message can be
left 24 hours a day, 7 days a week.
To Order: Provide the complete furniture
model number, part letter, production code,
quantity needed, reason for replacement
and your full name and address along with
a telephone number in case we need to
contact you.
Parts ship from our Eugene, Oregon factory
within 1 or 2 business days from the time
we receive the request. Please allow 5-10
business days for delivery.
This fine piece of furniture will make a handsome
addition to your home. For the best results, start
by reading the Assembly Instructions before you
begin your project.
Do not sit, stand or climb on this piece
of furniture.
Store the item: 1) in the box; 2) in a dry place; 3) in
temperatures ranging from 40° to 90°. (Not on a cold,
possibly damp, cement floor.)
Inspect your furniture periodically for any loose glue
joints or screws, or any other problem which may be
affecting the stability of your furniture. Tighten or repair
as needed.
This Assembly requires two people.
DESIGN SUBJECT TO CHANGE WITHOUT NOTICE.
06/08
Glazed Antique Cherry Finish
Assembly Instructions
Fluted Pedestal Table
60" Round Plank Top
2903AFGAC

2903AFGAC Fluted Pedestal Table
60" Round Plank Top — Parts List
HARDWARE
Before beginning assembly, check that the quantities of parts received match those listed below.
If you need to replace a part, please refer to the following list for name and number.
Page 2 — 2903AFGAC — 06/08
B — Pedestal Assembly— Qty.1
M — 5/16"x3" Lag Bolt
(inserted)— Qty.1
A — Top Assembly — Qty.1
H — Cleats (attached) — Qty. 2
K — #12x2½" Pan Head Screw (inserted) — Qty.14
L — Insert Nuts (inserted) — Qty. 6
J — Apron (attached) — Qty. 2
I — #8x2" Black Screw (inserted) — Qty.16
C — Foot — Qty.
R — Top Support
(attached) — Qty. 1
N — 3/8"x4" Hanger Bolt
(inserted) — Qty. 8
4 O — ½"x2¼" Wood Dowel
(inserted) — Qty. 4
P — Leveler
(attached) — Qty. 4
Q — T-Nut
(inserted) — Qty. 8
D — ¼"x1¾" Hex Bolt
— Qty. 6
G — 3/8" Hex Nut — Qty. 8
2904AFGAC } x1
2905AFGAC } x1
E — 5/16" Flat washer — Qty. 8
F — 1/4" Flat washer — Qty. 10
(4 inserted)

ASSEMBLY INSTRUCTIONS
TOOLS REQUIRED:
Phillips Screwdriver, Mallet or Padded Hammer, 9/16" Wrench and 7/16" Wrench
Page 3 — 2903AFGAC — 06/08
E
C
B
A
D
F
G
2903AFGAC Fluted Pedestal Table
60" Round Plank Top
1. Turn the Pedestal Assembly (B) upside-down so that the Top Support is on the floor. Apply a light film
of glue into each of the four dowel holes in the Pedestal Asssembly (see Fig. 1a). With a damp rag,
quickly wipe off any excess glue. Insert the Foot (C) into the holes on the Pedestal Assembly (B). The
Hanger Bolts should go all the way through the base. Gently tap feet into place with padded hammer.
Fasten in place with 5/16" washer (E) and 3/8" Hex Nut (G).
2. Turn the Top Assembly (A) upside down on a clean, protected surface. Align the holes in the Pedestal
Assembly (B) to the holes in the Top Assembly (A) as in Fig. 2 and attach with ¼" Flat Washers (F)
and ¼" x 1¾" Hex Bolts (D). See Fig. 2a. Turn upright and adjust levelers on the feet if needed.
O
DOWEL HOLE
Fig. 1
Fig. 1a
Fig. 2
F
D
Fig. 2a