Wiedamark SR-2820-US3 User manual

RF wireless wall mounted RGB/W controller
Parameter
SR-2820-US3
Product Size
Installation
Button introduction
Part No. Iuput Voltage Remarks
Current
SR-1009FA 12-36VDC Constant voltage
4x(60-180)W
4x5A
Output
SR-1009EA 12-36VDC Constant voltage
4x(96-288)W4x8A
Remote
Part No. Operation Voltage DIMENSIONS
ø/h (mm)
Operation
Frequency
SR-2820-US3 12-24VDC/
100-240VAC 120x75x29.1
434MHz/868MHz
Receiver
SR-1009FA3 12-36VDC Constant current
4x(4.2-12.6)W
4x350mA
SR-1009FA7 12-36VDC Constant current
4x(8.4-25.2)W4x700mA
Remarks
Touch Sensor
Wiring diagram
1)Sender DiagramConnection
110V-230VAC N
L
LN
110V-230VAC
Power Supply
12-24VDC
GND
SR-2820-US3(DC)
Vin L N
SR-2820-US3(AC)
3 zones
Sensitive Glass Touch Panel
Feature
RF Signal
White & black
North American Size
120.0
75.0
29.1
Color Wheel:
Touch to choose color
Brightness Color Running Button:
Short touch to start or Pause color
running mode;
Long touch to adjust speed (10 built-in
color running modes)
Warm white & Cold White &
Natural White, mixed by RGB
Switch: Short to switch on/offtouch
Zone Number:
Short touch 1. 2 . 3 to choose the zone
Long touch 1. 2 . 3 to switch on/off
Short to choose the color R.G.B.W
Long touch to dim brightness of R.G.B.W
touch

Safety & Warnings
Warranty Agreement
1) The product shall be installed and serviced by a qualified person.
2) IP20.Please avoid the sun and rain. When installed outdoors, please ensure it is mounted in a water proof
enclosure.
3) Always be sure to mount this unit in an area with proper ventilation to avoid overheating.
4) Please check if the output voltage of any LED power supplies used comply with the working voltage of the
product.
5) Never connect any cables while power is on and always assure correct connections to avoid short circuits
before switching on.
6)
7) For update information please consult your supplier.
Please ensure that the cable is secured tightly in the connector
1) We provide lifelong technical assistance with this product:
3-year warranty. We print date on every products, for example :1125 means year 2011,week 25.The
warranty is for free repair or replacement and covers manufacturing faults only.
For faults beyond the 3-year warranty we reserve the right to charge for time and parts.
2) Limited Warrenty
Any defects caused by wrong operation.
Any damages caused by unauthorized removal, maintenance, modifying, incorrect connection and
replacement of chips.
Any damages due to transportation, vibration etc. after purchase.
Any damages caused by earthquake, fire, lightning, pollution and abnormal voltage.
Any damages caused by negligence, inappropriate storing at high temperatures and humidity or near
harmful chemicals.
Product has been updated
3) Repair or replacement as provided under this warranty is the exclusive remedy to the customer.
2)Receiver Connection Diagram for Single Unit
3) Connection Diagram for Multiple UnitsReceiver
Power Supply
12-36VDC
LN
100V-240VAC
whi te
SR-1009FA
LED CONTROLLER
1234
Lea rni ng Ke y
whi te
SR-1009FA
LED CONTROLLER
1234
Lea rni ng Ke y
whi te
SR-1009FA
LED CONTROLLER
1234
Lea rni ng Ke y
Power Supply
12-36VDC
LN
100V-240VAC
whi te
SR-1009FA
LED CONTROLLER
1234
Lea rni ng Ke y
Operation
1. Do wiring according to connection diagram
2. Learning(matching).
a. Do wiring according to connection diagram
b. Wake up the wall controller by touching ON/OFF button.
c. Press learning button on receiver.
d. Touch any zone button on remote control.
e. Then touch color wheel.
f. Connected LED light will blink to confirm zone designation.
g. Press at learning button on receiver over 5 seconds until LED light flash, then delete the learned ID.
Note:
To choose a master from slaves by jumper for each zone.Short circuit for master. Open circuit for slave.
Each zone only can set 1 slave to be master. After a period of time, the master will do synchronization operation
to keep the same color or mode of all slaves in one zone.
3.Choose color by touching color wheel
After the receiver learned the ID, you can change each receiver's color by touching color wheel. If you want to
change the color of receiver NO.1.. Press zone button 1 or 2 or 3 which learned receiver No. 1, then touch color
wheel to choose your favorite color. If you want to control all the 3 zones at the same, just press button 1 & 2 &,
then touch color wheel .
4. Choose color changing mode
If you want 1 or 2 or 3 zones for color changing mode, press any zone button , then press button for
running. Press to stop the color you like.
5.Brightness adjustment
Under the static color or color changing status, adjust the brightness by press .