Wild tech ME2602-1 User manual

7
-
8. FixtureCleaning
The cleaning of internaland externalopticallensesand/or mirrorsmust be carried out
periodicallyto optimize lightoutput.Cleaning frequencydepends onthe environmentin
whichthe fixtureoperates: damp, smokyor particularly dirtysurrounding cancause greater
accumulationofdirt onthe unit soptics.
Ÿ Cleanwithsoftclothusing normal glass cleaning fluid.
Ÿ Always drythe partscarefully.
Ÿ Cleantheexternaloptics at leastevery20days.Cleanthe internalopticsat least
every30/60 days.
ECDeclaration of Conformity
Wedeclare that our products(lightingequipments)complywiththe following
specification andbears CEmarkinaccordancewiththeprovisionof the
ElectromagneticCompatibility(EMC)Directive 89/336/EEC.
EN55014-2: 1997 A1:2001, EN61000-4-2: 1995;EN61000-4-3:2002;
EN61000-4-4: 1995;EN61000-4-5:1995, EN61000-4-6:1996,
EN61000-4-11: 1994.
&
HarmonizedStandard
EN60598-1: 2004
IEC60598-1:2003+ corrigendum 2004
Part 1:Generalrequirements and test
Followingthe provisions of the low voltage directive 73/23/EEC and 93/68/EEC
Innovation , Quality, Performance
ME2602-1 UserGuide
Professional EntertainmentTechnology

1
-
.
TABLEOF CONTENTS
1.Introduction
2.SafetyInstruction
3.Description
4.Operationand TechnicalSpecification
5.Lampinstallation orreplacement
6.BeamAngle
7.Troubleshooting
8. FixtureCleaning
6
-
7. Troubleshooting
ProblemProbablecause(s) Suggestedremedy
Nopowerto the fixture Checkpower connections
Blown fuseIfpower is applied butdoesnot
light, pleasecheckandreplace
fuse if necessary.
Burned outlampInstallnew lamp.
No light
Fixture too hot Allow tocooldown. Improve air
flowaround the unit.
Sound too lowtoactivate
controlcircuit
Increasevolume.No action
Electricalmalfunction Refer to service technician.

5
-
Specification:
Voltage: AC120V~60Hz
Fuse:20mm glass 250VT6.3A
Bulb: ELC 24V 250W
Dimension:306 x263 x140 mm
Weight:8 kgs
5. Lampinstallation orreplacement
Always switchoffthe mainssupplyand neverhandle the lamp or luminaire whenit is hot.
Do not touch the bulb with bare hands. If this does happen, cleanthe lamp with denatured
alcoholand wipe witha lintfree clothbefore installing.
6. Beam angle
The Projector is bestto be placed 5meters fromwall,and fromthisdistance the lighteffect
will cover an area of 3.7 mx3.7m.
Pullthe socket off thelamp.
Do not pullthe wires.
2
-
1. Introduction
ThankyouforpurchasingWildTechsME2602-1.Itisaunique250W kaleidoscopiceffect
thatprojectsaswarmofswirlingpatterns. Comeswithgreat built-inprogramswithauto
movement orsoundactivation. It'slinkable, performingsynchronizedlightshow,perfectfor
discos, clubs, bars, and parties.
2. SafetyInstruction
WARNING
♦ Pleasekeepthis UserGuide forfuture consultation. If yousell theunit toanotheruser,
be sure that they also receive this instructionbooklet.
♦ Unpack and check carefully there is no transportation damage before using the unit.
♦ Beforeoperating,ensure thatthe voltageandfrequencyof power supplymatchthe
power requirementsofthe unit.
♦ Itsimportanttogroundtheyellow/greenconductortoearthin orderto avoidelectric
shock.
♦ The unitis forindoor use only.Use onlyin a drylocation.
♦ The unitmust be installedinalocationwithadequate ventilation,atleast 50cmfrom
adjacentsurfaces.Be sure thatno ventilationslots are blocked.
♦ Disconnect mains powerbeforefuse/lamp replacementor servicing.
♦ Replace fuse/lamponly withthe same type.
♦ Makesure there is no flammable materials close tothe unitwhile operating as it is fire
hazard.
♦ Use safetycable whenfixesthisunit.
♦ Maximumambient temperatureisTA: 40 .Dont operateitwhere thetemperature is
higher than this.
♦ Unitsurfacetemperature mayreachupto 85 .Don ttouch thehousingbare-hand
duringits operation.Turnoff the powerand allowabout 15 minutesfor the unit tocool
down before replacing bulborserving.
Please readcarefullytheinstruction,whichincludes important information
about theinstallation,usageandmaintenance.

3
-
♦ Inthe eventof serious operatingproblem, stopusing theunit immediately.Never tryto
repairthe unitbyyourself. Repairs carried outbyunskilledpeople canlead todamage
or malfunction.Please contactthe nearestauthorizedtechnicalassistance center.
Alwaysuse the same type spare parts.
♦ Dontconnect the deviceto any dimmer pack or power pack.
♦ Do not touchany wire during operationashighvoltage mightbe causingelectric
shock.
.
Warning
♦ Topreventor reduce theriskof electrical shock orfire, donotexpose the unit to rainor
moisture.
♦ Never touchbulbwithbarefingers as itis veryhot after using.
♦ Hot lampexplosionhazard. Donot opentheunitwithin fiveminutesafter switching off.
♦ Do not start on the unitwithoutbulb enclosureor housing aredamaged.
♦ The housing,thelenses,ortheultraviolet filter mustbereplacediftheyare visibly
damaged.
♦ Do not lookdirectly at the light while the bulb is on.
Caution
There are nouser serviceablepartsinsidethe unit. Donot open thehousing or attempt
any repairs yourself. In the unlikely event your unitmayrequireservice, please contact
yournearest dealer.
Rigging the fixtures
The unitshould bemounted via itsscrewholes on the bracket. Alwaysensure that the
unit is firmly fixed toavoid vibrationand slipping while operating. Always ensure that the
structureto whichyouareattachingtheunitissecure and isabletosupportaweightof
10 times oftheunit sweight.Alsoalwaysuse asafetycable that can hold12 times ofthe
weight of the unitwheninstalling the fixture.
The installation mustbe carried outbyqualified service people only.The deviceshould
be installed outof reachof peopleandoutside areaswhere persons maywalk byor be
seated.
4
-
3. Description
1.Optical lenswithmanualfocus adjustment.
2.Hangingbracketwith2knobs on both sides to fasten theunitand a mounting holetofixa
mounting hook.
3.Mains inputwith CIEsocketand integrated fuse holder, connect the suppliedmainscable
here.
4.Lamp compartment, to be openedwiththis knob
5.Internalmicrophone
6. ¼” jack used to connectthe optionalCA-8 controller.
7.Two 3.5mm stereo jacks usedto synchronize severalunits.
8.Cooling fan.
4. Operationand TechnicalSpecification
Plugging into the mainspower, the fixturestartsrunning.
The ME2602-1 runsinautomatic or sound activatedmode.
Precise opticswithspecialgobo / color wheel.
Linkableby using stereocable with3.5mm stereo
jack(optional)
Focusadjustable and fan cooled.
WitheasycontrollerCA-8 ( Optional) formanylighting shows as listed below.
Stand by
Blackout theunit
Function
Speed of gobo wheel
and mirrored-tunnel:
Fast and slow
Speedofgobowheel
and mirrored-tunnel:
Fastandslow
a.)Adjustgobo wheel rotating
directionand speed.
b.)Adjust mirrored-tunnel
rotating directionand speed.
Mode Sound
(LED off ) Auto (LEDon) Latch (LEDblinking)