Wildfire UltraBlade UB-44 User manual

Operation Manual
Ultraviolet LED Lighting Fixtures
UB-44
UB-42
UB-41
UB-21
BYWILDFIRE
ULTRABLADE

Table of Contents
Introduction 3
Safety Information 3
Specifications 4
Setup and Operation 5
Unpacking 5
Optional Accessories 5
Setup 5
Maintenance & Troubleshooting 6
Lamp Replacement 6
Cleaning 6
Troubleshooting 6
Diagrams 7
Isometric & Line Views UB-44 7
Isometric & Line Views UB-42 8
Isometric & Line Views UB-41 9
Isometric & Line Views UB-21 10
Exploded View & Part List UB-44-1 11
Exploded View & Part List UB-44-2 12
Exploded View & Part List UB-42-1 13
Exploded View & Part List UB-42-2 14
Exploded View & Part List UB-41-1 15
Exploded View & Part List UB-41-2 16
Exploded View & Part List UB-21-1 17
Exploded View & Part List UB-21-2 18
Schematic UB-44-1 19
Schematic UB-44-2 20
Schematic UB-42-1 & UB-42-2 21
Schematic UB-41-1 & UB-41-2 22
Schematic UB-21-1 & UB-21-2 23
Spectral Output Graph 24
Photometrics Chart 24
Limited Warranty 25
2

Introduction
Congratulations on your purchase of an UltraBlade LED lighting series fixture by Wildfire. These powerful and
versatile ultraviolet LED lighting fixtures feature Wildfire’s SableLED UV LED tube lamps. Each UltraBlade LED
fixture is precision engineered to provide you with years of trouble-free service. Please take a moment to read
this manual thoroughly before attempting to operate this fixture improper set-up, use or servicing may cause
damage to the fixture and/or lamps and void the warranty.
Safety Information
DANGER – RISK OF ELECTRIC SHOCK OR FIRE - USE ONLY WILDFIRE SABLELED LED TUBE LAMPS
MODEL L30T9/BLB (4’) AND L15T9/BLB (2’). DO NOT INSTALL FLUORESCENT LAMPS IN THIS FIXTURE.
WARNING - THIS FIXTURE EMITS ULTRAVIOLET RADIATION (UV) AT A PRIMARY WAVELENGTH OF
365NM, AVOID EYE AND SKIN EXPOSURE AT DISTANCES SHORTER THAN 3.3’ (1m). DO NOT LOOK
INTO THE LAMPS DIRECTLY AT DISTANCES SHORTER THAN 11’ (3.3m) OR VIEW THE LAMPS
DIRECTLY WITH OPTICAL INSTRUMENTS THAT MAY CONCENTRATE THE LIGHT/RADIATION OUTPUT.
CAUTION – WHEN USED IN ACCORDANCE WITH THE MANUFACTURERS OPERATING INSTRUCTIONS,
NO HAZARDS EXIST TO MOST PEOPLE AT DISTANCES GREATER THAN 11’ (3.3m) FROM THE FIXTURE.
HOWEVER, INDIVIDUALS SUFFERING FROM A RANGE OF SUNLIGHT EXPOSURE DISORDERS,
APHAKIC AND PSEUDOAPHIKIC, OR THOSE INDIVIDUALS RECEIVING PHOTOSENSITIVE MEDICATION
MAY RECEIVE DISCOMFORT IF EXPOSED TO ULTRAVIOLET LIGHT.
CAUTION – NOT FOR RESIDENTIAL USE. DRY INDOOR LOCATIONS ONLY. SUITABLE FOR SURFACE
MOUNTING ONLY.
Designed, Engineered and Built in the USA
3

Specifications
Housing:
18 Ga. aluminum with stainless steel hardware
Finish:
Flat black powder coat
Mounting:
Keyhole slot or Spring mounting brackets
Sockets:
Positive locking medium Bi-Pin G13
Input Voltage:
100-240VAC
Input Current:
UB-21: 0.15A Max
UB-41: 0.18A Max
UB-42: 0.83A Max
UB-44 1.66A Max
Frequency:
50-60Hz
Power Factor:
0.83
Power Consumption:
UB-21: 9W
UB-41: 15W
UB-42: 30W
UB-44 60W
Operating Temperature:
-4° F to 13° F (-20° F to 45° C)
Humidity:
0-80% non-condensing
Power Cord:
6’ 16/3 SOW with PowerCON and male Edison (PowerCON Models Only)
Power Input Connections
Neutrik PowerCON (PowerCON Models Only)
Power Output Connection:
Neutrik PowerCON, Max 4.0A (PowerCON Models Only)
Lamps:
UB-21:One Wildfire SableLED L9T8/BLB UV LED Tube Lamp
UB-41:One Wildfire SableLED L15T8/BLB UV LED Tube Lamp
UB-42:Two Wildfire SableLED L15T8/BLB UV LED Tube Lamps
UB-44: Four Wildfire SableLED L15T8/BLB UV LED Tube Lamps
Peak Wavelength:
365nm
Beam Angle:
120°
Lamp Life:
40,000 Hrs.
Dimensions:
UB-21: 3.12”/7.92cm High x 2.00”/5.08cm Wide x 24.37”/61.90cm Long
UB-41: 3.12”/7.92cm High x 2.00”/5.08cm Wide x 48.37”/122.86cm Long
UB-42: 3.12”/7.92cm High x 3.50”/8.89cm Wide x 48.37”/122.86cm Long
UB-44: 3.12”/7.92cm High x 6.82”/17.32cm Wide x 48.37”/122.863cm Long
Weight:
UB-21: 1.80 lbs./.81kg.
UB-41: 3.20 lbs./1.45kg.
UB-42: 4.40 lbs./1.99kg.
UB-44: 8.80lbs./3.99kg.
IP Rating:
IP-20 Indoor use
Warranty:
Three Year Parts and Labor
Standard Equipment:
Wildfire SableLED UV LED Tube Lamps, Spring Mounting Clips, PowerCON Power Out Cable Connector
Optional Accessories:
147-021 Truss Clamp (All Models)
147-002 Safety Cable (All Models)
147-041 Floor Stand Kit (UB-42 & UB-44)
147-040 Adjustable L Bracket Kit (UB-42 & UB-44)
147-003 T-Bar Ceiling Mount (All Models)
4

Setup & Operation
Unpacking
Unpack the fixture and carefully inspect it for any signs of physical damage. Report any damage to Wildfire or
your local distributor immediately
Optional Accessories:
Truss Clamp – These clamps when attached to both of the optional adjustable mounting brackets allows you to
mount the fixture to a standard 2” pipe truss. Contact Wildfire or your local distributor for pricing.
Safety Cable- This cable is to be used when installing the fixture on a pipe truss with the optional Adjustable L
Brackets and Truss Clamps. It attaches to the Adjustable L Brackets on either side of the UltraBlade model UB-
42 fixture securing it from falling if the clamps are not tightened properly. Contact Wildfire or your local
distributor for pricing.
Floor Stand Kit- This aluminum stand set attaches to the optional Adjustable L Bracket Kit enabling you to
mount the UltraBlade models UB-42 & UB-44 fixtures on the floor for footlight applications. Contact Wildfire or
your local distributor for pricing.
Adjustable L Bracket Kit- These brackets enable you to mount the UltraBlade models UB-42 & UB-44 fixtures
to a flat surface or truss system using the optional Truss Clamps and then adjust the fixture to the desired angle.
Contact Wildfire or your local distributor for pricing.
T-Bar Ceiling Mount- These brackets enable you to mount the UltraBlade models UB-42 & UB-44 fixtures to
the T-bars on a standard drop ceiling. Contact Wildfire or your local distributor for pricing
Setup
Connect the blue PowerCON cable connector on the power cord to the blue PowerCON AC Input panel
connector on the fixture. The fixture is also supplied with a gray PowerCON cable connector, enabling you to
interconnect additional fixtures. Do not connect more than 4.0A Max to the PowerCON AC Output
connector
Plug the fixture into the appropriate properly grounded power source. If you are controlling the unit with a
lighting control board you will need to make sure it is plugged into a non-dim circuit. Do not at any time plug
the fixture into a dimmable circuit, doing so will damage the LED lamps in the fixture and void the
warranty.
Operation
To turn the fixture on switch the rocker switch on the side of fixture to the ON position. Unplug the fixture from
the AC power outlet during prolonged periods of non-operation.
5

Maintenance & Troubleshooting
LED Lamp Replacement
Turn the power switch to the off position and unplug the fixture. If this is not possible then steps should be taken
that would allow the fixture to remain in an off state while re-lamping. Holding the lamp firmly with two hands,
one hand near each end of the lamp, rotate the lamp about its long center-line axis, one quarter (1/4) turn either
clockwise or counter-clockwise. The sockets will click, and the lamp will become loose. Lift the lamp free of the
sockets. Install the new lamp by lining up the two pins on the ends of the lamp so that they will slide into the
open slot in the lamp holder. Set the lamp into the sockets until the lamp pins rest on the lamp socket. Turn the
lamp one-quarter (1/4) turn either clockwise or counter-clockwise, until the lamp socket makes a small click, or
you feel a detent position. Gently lift up on the lamp to make sure that both ends of the lamp are installed
correctly, neither end of the lamp should move in the socket.
Cleaning
At no time should any cleaning chemicals or abrasives be used to clean any part of the fixture. Always unplug
the fixture before cleaning. For normal cleaning, a dry soft cloth should be used to wipe any surface free from
dust and light dirt. If the fixture is heavily soiled, lightly dampen the cloth with a mild window cleaning agent and
wipe. Lamps should be cleaned using the same method; first use a dry soft cloth and then proceed with a
window-cleaning agent if lamp is too heavily soiled. Do not spray or apply any liquid directly to any part of the
fixture.
Troubleshooting
Other than the lamps, there are no user serviceable parts in the fixture.
6

Isometric & Line Views UB-44
7
Diagrams
7.0"
48.37"
3.12"
6.75"
48.12"

Isometric & Line Views UB-42
8
48.37"
3.75"
48.12"
3.12"
3.50"

Isometric & Line Views UB-41
9
48.12"
48.37"
3.25"
3.12"
2.0"
AC INPUT

Isometric & Line Views UB-21
10
3.25"
3.12"
2.0"
24.12"
24.37"
AC INPUT