WILMS Selve SE Plus RC User manual

Selve SE Plus RC
Motorisation
manual

The SELVE SE PLUS RC is a radio-controlled motor and is used
in the following Wilms products:
• WCA0200 ZipX Sky (different setting)
• WPA0600 Terrace awning (different setting)
• WRB0600 ZipX Zero
• WRB0500 Built-on Screen
• WVS0200 Rolvent Screen
• WRB0200 ZipX 85
• WRB0300 ZipX 95
• WRB0400 ZipX 120
Attention!
• This type of motor is set using a SELVE transmitter.
• Every SELVE transmitter has a led light. This light is important. Make sure you keep an eye on it during the installation. By pressing a
button, the led light will ash every 3 seconds. This is an additional control for counting the seconds.
• It is allowed to supply power to all motors at once.
• Continue within 4 minutes after the start of the installation. If you don't do this, you will have to switch off the power and start all over again.
Press the SELECT button of the transmitter for 3 seconds.
When you have more than one product, you can search for the
right product by briey pressing the SELECT button until the
right motor reacts.
SETTING END POSITIONS
1. Press the STOP-button of the transmitter for 6 seconds. The
led light ashes twice.
2. Move the screen to the desired lower end position and conrm
by pressing the STOP-button for 3 seconds. The movement is
interrupted once.
3. Move the screen to the desired upper end position and
conrm by pressing the STOP-button for 3 seconds. Once
again, the movement is interrupted once.
4. The end positions are set.
5. Press the PROG-button. The led light lights up green.
6. Press the SELECT-button for 3 seconds to complete the
installation or continue to the next screen by pressing the
SELECT-button for 1 second.
RESET END POSITIONS
1. Always start by pressing the SELECT-button for 3 seconds.
The motor makes a short movement.
2. Press the PROG-button for 9 seconds.
3. Follow the steps for setting the end positions.
Questions?
Please contact our B2B customer service at any time.
Selve SE Plus RC
Motorisation manual
2
1
6 sec.
3
3 sec.
3 sec.
5 6
PROG SELECT
3 sec.
1 sec.
1 2
PROG
SELECT
3 sec. 9 sec.

The SELVE SE PLUS RC is a radio-controlled motor and is used
in the following Wilms products:
• WCA0200 ZipX Sky
• WPA0600 Terrace awning
Press the SELECT button of the transmitter for 3 seconds.
When you have more than one product, you can search for the
right product by briey pressing the SELECT button until the
right motor reacts.
1. Press the STOP button of the transmitter for 6 seconds. The
led light ashes twice.
2. Move the screen to the desired lower end position and conrm
by pressing the STOP button for 3 seconds. The movement is
interrupted once.
3. Move the screen to the desired upper end position and keep
the button pressed until the screen stops automatically.
4. The end positions are set.
5. Press the PROG button. The led light lights up green
6. Press the SELECT button for 3 seconds to complete the
installation or continue to the next screen by pressing the
SELECT button for 1 second.
RESET END POSITIONS
1. Always start by pressing the SELECT button for 3 seconds.
The motor makes a short movement.
2. Press the PROG button for 9 seconds.
3. Follow the steps for setting the end positions.
Questions?
Please contact our B2B customer service at any time.
Selve SE Plus RC
Motorisation manual
2
1
6 sec.
3
3 sec.
5 6
PROG SELECT
3 sec.
1 sec.
1 2
PROG
SELECT
3 sec. 9 sec.