WilTec AOYUE 486 User manual

User’s Manual
AOYUE 486 Smoke Absorber
91486
Illustration similar, may vary depending on model
Please read and follow the operating instructions and safety information prior to initial operation.
Technical changes reserved!
Illustrations, functional steps, and technical data may deviate insignificantly due to continuous further
developments.

© by WilTec Wildanger Technik GmbH Item 91486 Page 2
http://www.WilTec.de
http://www.aoyue.eu 02 2023-1
http://www.teichtip.de
The information contained in this document may alter at any time without prior notice. No part of this
document may be copied or otherwise duplicated without prior written consent. All rights reserved.
WilTec Wildanger Technik GmbH cannot be held liable for any possible mistakes in this operating man-
ual, nor in the diagrams and illustrations shown.
Although WilTec Wildanger Technik GmbH has made every possible effort to ensure that this operating
manual is complete, accurate, and up-to-date, errors cannot be ruled out entirely.
If you have found an error or wish to suggest an improvement, we look forward to hearing from you.
Send us an e-mail to:
[email protected]
or use our contact form:
https://www.wiltec.de/contacts/
The most recent version of this manual in several languages can be found in our online shop:
https://www.wiltec.de/docsearch
Our postal address is:
WilTec Wildanger Technik GmbH
Königsbenden 12
52249 Eschweiler – Germany
To return your goods for exchange, repair, or other purposes, please use the following address. Atten-
tion! To allow for a trouble-free complaint or return, it is important to contact our customer service team
before returning your goods.
Retourenabteilung
WilTec Wildanger Technik GmbH
Königsbenden 28
52249 Eschweiler – Germany
E-mail: [e-mail]
Tel: [phone]
Fax: [phone]

© by WilTec Wildanger Technik GmbH Item 91486 Page 3
http://www.WilTec.de
http://www.aoyue.eu 02 2023-1
http://www.teichtip.de
Introduction
Thank you for choosing to purchase this quality product. To minimise the risk of injury, we ask you to
always take some basic safety precautions when using this product. Please read this operating manual
carefully and make sure that you understand it.
Keep these operation instructions in a safe place.
ATTENTION:
•Always use an earthed power supply with the correct voltage. The corresponding voltage value
is given on the nameplate. If there are doubts concerning the earthing of the power supply,
contact a qualified person for checking it. Never use a damaged power cable.
•Do not open this device in a damp or wet area or with yourself being wet and protect it from
direct sunlight. Install the device in a safe place so that nobody can walk on the cables, fall over
them, and/or damage them. Make for sufficient cooling by ambient air and avoid any heat build-
up.
•Before cleaning the device, pull out the plug and only use a damp cloth for cleaning. Avoid using
cleaning agents and make sure that liquids cannot enter the device.
•The inner parts of the device do not contain components requiring maintenance by the user.
Leave all maintenance, control, and repair works to a qualified person. In case of unqualified
intervention, the 2-year warranty will expire.
•Read all safety precautions and instructions. Failure to obey the safety precautions and
instructions might cause an electric shock, a fire, and/or severe injuries. Keep all safety precau-
tions and instructions for future use.
Safety instructions
General safety instructions
•The use of this device is only allowed with a fault current protection switch with a triggering
nominal current up to 30 mA (according to VDE 0100 Article 702 and 738).
•The device is not intended for use by persons (including children) with impaired or limited phys-
ical, sensory, and mental abilities or lack of experience and/or real knowledge, unless they are
supervised by a person responsible for their safety or follow the instructions made by this person
on how to correctly use the device.
•Children should be supervised to ensure that they do not play with the device.
•During operation, the unsoldering gun, hot air piston, and nozzle have temperatures between
200 ℃ and 480 ℃. Therefore, personal injuries or material damage inside the work area might
happen in case the unsoldering station is not handled with care.
•Obey the following principles when working with this device:
oAfter opening the parcel, check if every individual part of the device is in good condition or
if you can detect visible damage caused by transport. If there are damages visible, do not
operate the device, but immediately contact your vendor.
oSwitch off the device and pull out the plug before moving it.
oAvoid exposing parts of the device to too high a mechanical stress (shocks, pushes, etc.).
•Perform a visual inspection of the device before every use. Do not use the device if the safety
appliances are damaged or worn out. Never override safety regulations.
•Only use the device accordingly to the intended purpose stated in this manual.
•You are responsible for the safety of the working zone.
•If the cable or the plug is damaged due to external influences, the cable must not be repaired,
but must be replaced with a new one.
•The voltage of 230 V AC indicated on the nameplate of the device must match the existent
mains voltage.
•Never lift, carry, or fix the device by using the power cable.
•Make sure that the electrical plug connection is protected from flood and moisture.
•Always unplug the device before working on it.

© by WilTec Wildanger Technik GmbH Item 91486 Page 4
http://www.WilTec.de
http://www.aoyue.eu 02 2023-1
http://www.teichtip.de
•Avoid exposing the device to direct jets of water.
•The user is responsible for complying with local safety and mounting regulations. If necessary,
ask a qualified electrician.
•In case of device failure, repairs can only be carried out by an electrician.
Electrical connection
The electrical connection is made to an earthed socket 230 V ~ 50 Hz. Fuse min. 10 A.
Commissioning
•Place the device on a level and solid surface the temperature of which does not exceed 40 ℃.
Place the device horizontally to allow the station to operate correctly.
•Connect to mains.
Scope of delivery
•Fume extractor
•Solid washable filtering element
•Stable support
Technical specifications
Intake voltage (V)
230 ±10 %
Frequency (㎐)
50 ±2
Motor type
Carbonless
Weight (㎏)
1.36
Features and functions
•Quiet and powerful operation
•With replaceable activated carbon filter
•With a unique filter to reduce the resistance and to achieve a high suction power

© by WilTec Wildanger Technik GmbH Item 91486 Page 5
http://www.WilTec.de
http://www.aoyue.eu 02 2023-1
http://www.teichtip.de
Regulations for waste disposal
The Waste Electrical and Electronic Equipment Directive (WEEE Directive, 2012/19/EU) of the EU was
implemented in the German law related to electrical and electronic equipment and appliances.
All WilTec electric devices that fall under the WEEE directive are labelled with the symbol of a crossed-
out wheeled rubbish bin. This symbol indicates that this electric device must not be disposed of with the
domestic waste.
WilTec Technik GmbH is registered with the German registration authority EAR (Stiftung Elektro-
Altgeräte Register) under the WEEE-registration number DE45283704.
Disposal of used electrical and electronic devices (in-
tended for use in the countries of the European Union
and other European countries with a separate waste
collection system for these devices).
The symbol on the packaging or the product itself indi-
cates that this product must not be treated as normal
domestic waste but must be disposed of at a recycling
collection station for electrical and electronic waste.
By disposing of this product correctly, you contribute to
the protection of the environment and the health of your
fellow people. Inappropriate disposal threatens the en-
vironment and health.
Material recycling helps to reduce the consumption of raw materials.
Additional information about the recycling of this product can be provided by your local commune, the
municipal waste disposal facilities, or the store where you purchased the product.
Address:
WilTec Wildanger Technik GmbH
Königsbenden 12 / 28
52249 Eschweiler Germany
Important Note:
Reproduction and any commercial use (of parts) of this operating manual, requires a written permission
of WilTec Wildanger Technik GmbH.