wimesure MP6Plus User manual

www.wimesure.fr • [email protected] • 01 30 47 22 00
Photos non contractuelles - Les spécications peuvent être modiées sans préavis - wimesure.fr • MB 2021
41126 Cognento (MODENA) Italy Via Bottego 33/A Tel:[phone] Fax:[phone] E-mail: [e-mail]
MP6P
P
l
l
u
u
s
s
PROFESSIONAL INDICATOR
for measures of
Force 

Weight 

Pressure


Torque 

Displacement

Temperature
USER GUIDE
MO.MP6Plus.R7

www.wimesure.fr • [email protected] • 01 30 47 22 00
Photos non contractuelles - Les spécications peuvent être modiées sans préavis - MP6Plus R0 - wimesure.fr • AH 2022
MP6P
P
l
l
u
u
s
s
USER GUIDE MO.MP6Plus.R7
Pag. 1
INDEX
1. Declaration of Conformity
2
42. Calibration for Incremental Encoder Channel
38
2. Identification
2
43. Channel Linearization
39
3. Unauthorized uses
2
44. Printer Header
41
4. Disposal
2
45. Data Logger Menu (Option)
42
5. Introduction
3
46. Data Logger Parameters
42
6. Available Fittings
4
47. View Data Logger
44
7. Component Supplied
5
48. Copy Data Logger
44
8. Components in Options
5
49. Files for USB Flash Memory
45
9. Software Applications(optional)
6
50. Digital Input (Option)
46
10. TECHICAL DATA
8
51. Analog Output (Option)
49
11. Purchase Codes
9
52. SetPoint
52
12. Dimensions
10
53. RS232 and Printer Communication Parameters
53
13. Trasport
11
54. RS485 Communication Parameters
54
14. Positioning
11
55. Key Block
55
15. INSTALLATION
11
56. Channel Enable and TOTAL Function
56
16. Maintenance
11
57. Wireless Transmission Parameter
57
17. Power On
12
58. Service and LCD Contrast
58
18. Power Off
12
59. Save Channels
59
19. Display and Function Keys
13
60. Restore Channels
59
20. Main Page
15
61. MODBUS RTU Communication Protocol
60
21. Error Messages
16
62. RS232 Communication Protocol
62
22. ZERO Function
16
63. USB Communication Protocol
64
23. PEAK Function
17
64. Sw Examples
66
24. HOLD Function
18
65. Read Command
69
25. UNLOAD Function
18
66. Write Commands
71
26. DATALOGGER Function
19
67. Continuos transmitting mode
73
27. COUNTER Function
22
68. DataLogger Management commands
74
28. PRINTER Function
24
69. Rear Panel Connectors
75
29. MAIN MENU
25
70. RS232 Connections
76
30. Measurement Unit
26
71. RS485 Connections
77
31. Reolution
27
72. 24V Digital Input Connections
78
32. Point Position
27
73. Analog Output Connections
79
33. Digital Filter e Frequency of Acquisition
28
74. Transducers Connections
80
34. Configuration
30
75. Load cells Connections
81
35. Date and Time setting (option)
31
76. Amplified Transducers Connections
82
36. Channel Setup
32
77. PT100 Connections
82
37. Force, Pressure, Torque and Displacement
Channel Calibration
33
78. Incremental Encoder Connections
83
38. Full Scale Calibration
34
79. Power Supply and Part Identification
84
39. Known Weight Calibration
36
40. Calibration by interlation points
37
41. Calibration for Temeprature Channels
38
TABLE 1 : pag 26
TABLE 2 : pag 61
TABLE 3 : pag 61
TABLE 4 : pag 61
AEP transducers holds the right to make any change when necessary, without notice.
The data contained in this manual are just indicative and the manufacturer declines any responsibility for
errors or discrepancies with respect to this manual.

www.wimesure.fr • [email protected] • 01 30 47 22 00
Photos non contractuelles - Les spécications peuvent être modiées sans préavis - MP6Plus R0 - wimesure.fr • AH 2022
MP6PPlluussUSER GUIDE MO.MP6Plus.R7
Pag. 1
INDEX
1. Declaration of Conformity
2
42. Calibration for Incremental Encoder Channel
38
2. Identification
2
43. Channel Linearization
39
3. Unauthorized uses
2
44. Printer Header
41
4. Disposal
2
45. Data Logger Menu (Option)
42
5. Introduction
3
46. Data Logger Parameters
42
6. Available Fittings
4
47. View Data Logger
44
7. Component Supplied
5
48. Copy Data Logger
44
8. Components in Options
5
49. Files for USB Flash Memory
45
9. Software Applications(optional)
6
50. Digital Input (Option)
46
10. TECHICAL DATA
8
51. Analog Output (Option)
49
11. Purchase Codes
9
52. SetPoint
52
12. Dimensions
10
53. RS232 and Printer Communication Parameters
53
13. Trasport
11
54. RS485 Communication Parameters
54
14. Positioning
11
55. Key Block
55
15. INSTALLATION
11
56. Channel Enable and TOTAL Function
56
16. Maintenance
11
57. Wireless Transmission Parameter
57
17. Power On
12
58. Service and LCD Contrast
58
18. Power Off
12
59. Save Channels
59
19. Display and Function Keys
13
60. Restore Channels
59
20. Main Page
15
61. MODBUS RTU Communication Protocol
60
21. Error Messages
16
62. RS232 Communication Protocol
62
22. ZERO Function
16
63. USB Communication Protocol
64
23. PEAK Function
17
64. Sw Examples
66
24. HOLD Function
18
65. Read Command
69
25. UNLOAD Function
18
66. Write Commands
71
26. DATALOGGER Function
19
67. Continuos transmitting mode
73
27. COUNTER Function
22
68. DataLogger Management commands
74
28. PRINTER Function
24
69. Rear Panel Connectors
75
29. MAIN MENU
25
70. RS232 Connections
76
30. Measurement Unit
26
71. RS485 Connections
77
31. Reolution
27
72. 24V Digital Input Connections
78
32. Point Position
27
73. Analog Output Connections
79
33. Digital Filter e Frequency of Acquisition
28
74. Transducers Connections
80
34. Configuration
30
75. Load cells Connections
81
35. Date and Time setting (option)
31
76. Amplified Transducers Connections
82
36. Channel Setup
32
77. PT100 Connections
82
37. Force, Pressure, Torque and Displacement
Channel Calibration
33
78. Incremental Encoder Connections
83
38. Full Scale Calibration
34
79. Power Supply and Part Identification
84
39. Known Weight Calibration
36
40. Calibration by interlation points
37
41. Calibration for Temeprature Channels
38
TABLE 1 : pag 26
TABLE 2 : pag 61
TABLE 3 : pag 61
TABLE 4 : pag 61
AEP transducers holds the right to make any change when necessary, without notice.
The data contained in this manual are just indicative and the manufacturer declines any responsibility for
errors or discrepancies with respect to this manual.
MP6P
P
l
l
u
u
s
s
USER GUIDE MO.MP6Plus.R7
Pag. 2
1. DECLARATION OF CONFORMITY
Manufacter: AEP transducers s.r.l
Address: Via Bottego 33/A 41126 Cognento MODENA (Italia)
DECLARES THAT THE FOLLOWING PRODUCT
Product Name: MP6Plus
Type: PROFESSIONAL INDICATOR
Year of Construction: 2014
Options: this declaration covers all the options specified in the manual.
CONFORMS TO THE FOLLOWING DIRECTIVES:
2014/30/EU - 2014/35/EU - 2011/65/EU (RoHS) - 2012/19/EU (WEEE)
CONFORMS TO THE FOLLOWING NORMS:
EN 61010-1(2013) EN 61326-1 (2013)
CONFORMS TO THE REGULATION
n° 1907/2006 (REACH)
The product has been tested in the typical installation configuration, as described in the instruction manual. Above
described product meets the requirements of mentioned Norms, basing on both test results and considerations listed
in the technical file.
I declare that the product defined above meets the requirements of the Directives, of the Norms and Regulation
above mentioned.
41126 Cognento Modena (Italy) Date: 20/09/2014
Lioi Giovanni
2. IDENTIFICATION
On the rear panel of the instrument are marked in indelible mode all the informations for the identification, the main
configuration data, the symbols of conformity and waste disposal, the production date and the serial number.
3. UNAUTHORIZED USES
Environments with explosive atmosphere.
Environments with inflammable or corrosive gas.
4. DISPOSAL
The instrument is a professional apparatus compliant to the 2011/65/EU(RoHS) and 2012/19/EU (WEEE),
then it must be disposed separately as electric and electronic waste.
In different countries of European Community, it must be disposed as waste electric and electronic in
accord to the laws of the country where the device is commercialized.
Before to remove the instrument, you disconnect first the power supply and after the cables

www.wimesure.fr • [email protected] • 01 30 47 22 00
Photos non contractuelles - Les spécications peuvent être modiées sans préavis - MP6Plus R0 - wimesure.fr • AH 2022
MP6P
P
l
l
u
u
s
s
USER GUIDE MO.MP6Plus.R7
Pag. 3
5. INTRODUCTION
MP6Plus is an instrument with 1 (up to 4 as option) analog inputs (defined in this manual as channels), individually
programmable; each input is able to receive signals from strain gauge (standard version) full-bridge (4 or 6 wires) or
transducers with amplified output voltage (+/- 10V or +/- 5V), current (4- 20mA or 0-20mA) or PT100.
It is suitable for the measurement of forces, weight and pressure, displacement and temperature (PT100). It is realized
to be used in systems of static and dynamic measurement in an industrial environment where it is necessary to
acquire more independent transducers simultaneously and in a synchronized manner.
The instrument, in its basic version has, for each channel, an accuracy of 0.010% due to an 24bit internal resolution.
In the case of strain gauge inputs each channel has a standard resolution of 100.000 divisions.
MP6Plus can use load cells or dynamometers of 350 / 700with 4-wire or 6 wires connection.
Load cells power supply is realized using a switching voltage at a frequency equal to the sampling rate. This ensures a
better suppression of interference due to offset drift and to the connecting cables.
In the case of voltage input 10V or 5V MP6Plus has a resolution of 0.1mV respectively and 0.05 mV
(100000divisions) while in the case of current input 0-20mA or 4-20mA has a resolution of 0.1 uA (respectively
200000divisions and 160000divisions).
To measure the temperature one input can dedicated to sensors PT100 in a range from -50 ° C to 250 ° C with a
resolution of 0.1 ° C and accuracy +/- 1 ° C.
Each channel has a dedicated converter Sigma-Delta type 24bit and all conversions take place at the same time
(channel synchronization).
The sampling frequency (common to all channels) can be set from 2.5 samples per second up to 4800 samples per
second therefore the instrument meets the needs of applications that require a considerable speed of response.
The instrument is equipped with 4 digital inputs to realize simple automations.
The instrument can be equipped with up to 4 analog outputs (optional). Each input channel may be associated with
one or more analog voltage ouput (± 10V, 0 / 5V, 0 / 10V, ± 5V) or current (4-20mA).
MP6Plus allows you to enable/disable the display of each individual channels. In this way suits the needs of use in
different situation of use.
MP6Plus can be optionally equipped with a powerful datalogger that can be either internal (in an internal nonvolatile
memory, which allows to exploit the maximum speed of acquisition), that external using a conventional USB stick. The
files created can be directly exported to Microsoft Excel being in csv format.
Data communication can take place simultaneously and concurrently through USB ports, RS232 and RS485.
MP6Plus main features are:
Large size and high resolution graphic display.
1 (up to 4 as option) external connections to transducers: 2mV/V, +/-10V, +/-5V, 4-20mA, 0-20mA ,PT100
Selection of a large number of measurement unit for each of the connected channels.
Data Logger with internal non-volatile memory that can store up to 130,000 measurement points when
configured with a single channel (Option)
External Data Logger that uses a usual USB stick for easy portability of data on a PC (Option)
ZERO Function
HOLD Function
PEAK Function
COUNTER Function
UNLOAD Function to measure the quantity of material unloaded from a tank
TOTAL Function: to performs the cumulative sum of channels
AUTOZERO Function: to clear a channel output if is below for a certain time under a programmed threhold
Key Block : in order to avoid changes to the settings by unauthorized persons
Clock Calendar Function with date and time (Option)
Printer (Option) connected to the RS232 serial port through which it is possible to print the measurement
points and the data of the company which carried out the survey.
USB communication port through which you can transfer measurements in real time to a PC.
RS232 Serial communication port (Option)
Wireless Transmission (Option)
RS485 communication port (Option)
4 24Vdc digital inputs with programmable function (Option)
Up to 4 analogue outputs (option): 4-20mA, +/- 10Vdc, 0-10Vdc, 0-5Vdc, +/- 5VDC. The refresh rate of the

www.wimesure.fr • [email protected] • 01 30 47 22 00
Photos non contractuelles - Les spécications peuvent être modiées sans préavis - MP6Plus R0 - wimesure.fr • AH 2022
MP6PPlluussUSER GUIDE MO.MP6Plus.R7
Pag. 3
5. INTRODUCTION
MP6Plus is an instrument with 1 (up to 4 as option) analog inputs (defined in this manual as channels), individually
programmable; each input is able to receive signals from strain gauge (standard version) full-bridge (4 or 6 wires) or
transducers with amplified output voltage (+/- 10V or +/- 5V), current (4- 20mA or 0-20mA) or PT100.
It is suitable for the measurement of forces, weight and pressure, displacement and temperature (PT100). It is realized
to be used in systems of static and dynamic measurement in an industrial environment where it is necessary to
acquire more independent transducers simultaneously and in a synchronized manner.
The instrument, in its basic version has, for each channel, an accuracy of 0.010% due to an 24bit internal resolution.
In the case of strain gauge inputs each channel has a standard resolution of 100.000 divisions.
MP6Plus can use load cells or dynamometers of 350 / 700with 4-wire or 6 wires connection.
Load cells power supply is realized using a switching voltage at a frequency equal to the sampling rate. This ensures a
better suppression of interference due to offset drift and to the connecting cables.
In the case of voltage input 10V or 5V MP6Plus has a resolution of 0.1mV respectively and 0.05 mV
(100000divisions) while in the case of current input 0-20mA or 4-20mA has a resolution of 0.1 uA (respectively
200000divisions and 160000divisions).
To measure the temperature one input can dedicated to sensors PT100 in a range from -50 ° C to 250 ° C with a
resolution of 0.1 ° C and accuracy +/- 1 ° C.
Each channel has a dedicated converter Sigma-Delta type 24bit and all conversions take place at the same time
(channel synchronization).
The sampling frequency (common to all channels) can be set from 2.5 samples per second up to 4800 samples per
second therefore the instrument meets the needs of applications that require a considerable speed of response.
The instrument is equipped with 4 digital inputs to realize simple automations.
The instrument can be equipped with up to 4 analog outputs (optional). Each input channel may be associated with
one or more analog voltage ouput (± 10V, 0 / 5V, 0 / 10V, ± 5V) or current (4-20mA).
MP6Plus allows you to enable/disable the display of each individual channels. In this way suits the needs of use in
different situation of use.
MP6Plus can be optionally equipped with a powerful datalogger that can be either internal (in an internal nonvolatile
memory, which allows to exploit the maximum speed of acquisition), that external using a conventional USB stick. The
files created can be directly exported to Microsoft Excel being in csv format.
Data communication can take place simultaneously and concurrently through USB ports, RS232 and RS485.
MP6Plus main features are:
Large size and high resolution graphic display.
1 (up to 4 as option) external connections to transducers: 2mV/V, +/-10V, +/-5V, 4-20mA, 0-20mA ,PT100
Selection of a large number of measurement unit for each of the connected channels.
Data Logger with internal non-volatile memory that can store up to 130,000 measurement points when
configured with a single channel (Option)
External Data Logger that uses a usual USB stick for easy portability of data on a PC (Option)
ZERO Function
HOLD Function
PEAK Function
COUNTER Function
UNLOAD Function to measure the quantity of material unloaded from a tank
TOTAL Function: to performs the cumulative sum of channels
AUTOZERO Function: to clear a channel output if is below for a certain time under a programmed threhold
Key Block : in order to avoid changes to the settings by unauthorized persons
Clock Calendar Function with date and time (Option)
Printer (Option) connected to the RS232 serial port through which it is possible to print the measurement
points and the data of the company which carried out the survey.
USB communication port through which you can transfer measurements in real time to a PC.
RS232 Serial communication port (Option)
Wireless Transmission (Option)
RS485 communication port (Option)
4 24Vdc digital inputs with programmable function (Option)
Up to 4 analogue outputs (option): 4-20mA, +/- 10Vdc, 0-10Vdc, 0-5Vdc, +/- 5VDC. The refresh rate of the
MP6P
P
l
l
u
u
s
s
USER GUIDE MO.MP6Plus.R7
Pag. 4
analog signals is equal to the frequency of acquisition of the respective channels in input.
REPEATER Function: The instrument can be configured to display (in the form passive as Slave) measures
from the RS232 serial port (for example from another MP6Plus -Master) to a remote view of the measures.
In this case all the features enabled on the MP6Plus Slave will be active (Setpoint, USB, printer, logger etc).
The REPEATER function is active for one channel.
MP6Plus can be accompanied by the PC program MP Supervisor (Option) which allows immediate interface via the USB
port with the instrument and allows you to display graphs, export to Microsoft Excel.
The program also allows you to download the data logger performed using the internal memory and those on
performed on USB stick and view their acquisition curves.
6. AVAILABLE FITTINGS
KAL KAL CLF C8S CLB TCETM
System for the measurement of FORCE (compression and tension)combined with force transducers with ranges from
10N to 5000kN.
CLT CLS C2S F1
System for the measurement of WEIGHT in compression and tension matched to the load cells with ranges from 1kg
to 500t.
TP16 TP1
System for the measurement of PRESSURE and VACUUM (Empty) combined with pressure transducers.
Normalized ranges from 5 bar to 2000bar (29000psi) for use in gas and liquid.
TRX TRS TOR RT2
System for the measurement of TORQUE clockwise and counterclockwise combined with torque transducers static or
dynamic. Normalized ranges from 0.5 Nm to 5000 Nm, ability to record high-speed continuous PEAKS up to 4.8kHz.
.
LDT
System for the measurement of DISPLACEMENT transducers coupled with transducers with normalized ranges from 5
to 100 mm.

www.wimesure.fr • [email protected] • 01 30 47 22 00
Photos non contractuelles - Les spécications peuvent être modiées sans préavis - MP6Plus R0 - wimesure.fr • AH 2022
MP6P
P
l
l
u
u
s
s
USER GUIDE MO.MP6Plus.R7
Pag. 5
7. COMPONENTS SUPPLIED
Power Cord DB9 Male Connector CD with
for transducer Manual and USB Driver
8. OPTIONAL COMPONENTS (purchased separately)
USB cable
RS232 Serial Cable
Pair of mounting
brackets for panel
Desktop Printer
RS232 Interface
DB9 Male
Connector
For each
transducers
Calibration Report
ACCREDIA Certificate
(MP6+Transducer)
Calibratorfor mV/V
signals
Case for transport

www.wimesure.fr • [email protected] • 01 30 47 22 00
Photos non contractuelles - Les spécications peuvent être modiées sans préavis - MP6Plus R0 - wimesure.fr • AH 2022
MP6PPlluussUSER GUIDE MO.MP6Plus.R7
Pag. 5
7. COMPONENTS SUPPLIED
Power Cord DB9 Male Connector CD with
for transducer Manual and USB Driver
8. OPTIONAL COMPONENTS (purchased separately)
USB cable
RS232 Serial Cable
Pair of mounting
brackets for panel
Desktop Printer
RS232 Interface
DB9 Male
Connector
For each
transducers
Calibration Report
ACCREDIA Certificate
(MP6+Transducer)
Calibratorfor mV/V
signals
Case for transport
MP6P
P
l
l
u
u
s
s
USER GUIDE MO.MP6Plus.R7
Pag. 6
9. SOFTWARE APPLICATION (purchased separately)
To complete the system of measurement AEP transducers has developed several software applications that interface
directly to the instrument MP6Plus and support the user in the various functions of calibration, testing, analysis, data
storage, transfer of measures on Microsoft Excel etc. ...
MP Supervisor is a software dedicated to MP6Plus . Through this software you can download the data logger and
operate directly on MP6Plus to change parameters and create graphics test.
Quick Analyzer is a general purpose acquisition software where MP6Plus can be associated to other AEP instruments .
For more information download the manuals of the software on the site:
www.aeptransducers.com
www.aep.it

www.wimesure.fr • [email protected] • 01 30 47 22 00
Photos non contractuelles - Les spécications peuvent être modiées sans préavis - MP6Plus R0 - wimesure.fr • AH 2022
MP6P
P
l
l
u
u
s
s
USER GUIDE MO.MP6Plus.R7
Pag. 7
QuickAnalyzer
Dedicated to recording and graphical analysis of up to 16 different AEP transducers instruments to measure:
force, weight, pressure, torque and displacement.
MPSupervisor
A dedicated program that allows an immediate interfacing through the USB port with the MP6Plus and allows you to
view graphs, export data to Microsoft Excel directly from the PC and set all configuration parameters.
The program also allows you to download a Data Logger carried out using the internal memory or the USB Flash
Memory and display the respective curves of acquisitio

www.wimesure.fr • [email protected] • 01 30 47 22 00
Photos non contractuelles - Les spécications peuvent être modiées sans préavis - MP6Plus R0 - wimesure.fr • AH 2022
MP6PPlluussUSER GUIDE MO.MP6Plus.R7
Pag. 7
QuickAnalyzer
Dedicated to recording and graphical analysis of up to 16 different AEP transducers instruments to measure:
force, weight, pressure, torque and displacement.
MPSupervisor
A dedicated program that allows an immediate interfacing through the USB port with the MP6Plus and allows you to
view graphs, export data to Microsoft Excel directly from the PC and set all configuration parameters.
The program also allows you to download a Data Logger carried out using the internal memory or the USB Flash
Memory and display the respective curves of acquisitio
MP6P
P
l
l
u
u
s
s
USER GUIDE MO.MP6Plus.R7
Pag. 8
10. TECHNICAL DATA
ACCURACY
NON LINEARITY ERROR
≤± 0.010%
≤± 0.010%
STANDARD RANGE FOR STRAIN GAUGES TRANSDUCERS
STRAIN GAUGES RESOLUTION AT 2mV/V
RESOLUTION FOR +/-10V AND +/-5V TRANSDUCERS
RESOLUTION FOR 4-20mA AND 0-20mA transducers
TEMPERATURE RESOLUTION : PT100 2 WIRES (range -50°C –250°C)
INTERNAL RESOLUTION (ALL CHANNELS)
MAX NUMBER OF STRAIN GAUGE TRANSDUCERS CONNECTABLE
AMPLIFIED TRANSDUCERS (+/-10V or 4-20mA) CONNECTABLE
STRAIN GAUGE POWER SUPPLY
AMPLIFIED TRANSDUCERS POWER SUPPLY
ACQUISTION FREQUENCY (Programmable) (samples per second)
(for all channels)
2mV/V
100.000 div
0.1mV e 0.05mV (100000 div)
0.1 µA (resp. 160000 div and 200000div)
0.1°C accuracy: 1°C
24bit
Each channel: 2 @350or 4 @ 700
4
5V switching (3%)
20Vdc
2.5–5–10–20–50-100-200-400–600-1200–
2400-4800
INTERNAL DATALOG
MAX STORING POINTS
MAX STORING SPEED
Note: The maximum storage speed is however limited by
the acquisition frequency set

MAX TIME
4 channels + Total : 26000
4 channels: 32000
3 channels: 43000
2 Channels: 65000
1 Channel:130000
4 o 5 channels: 1200 points per second
3 Channels: 2400 points per second
1 o 2 Channels: 4800 points per second
100 days
EXTERNAL USB Flash Memory (Option)
MAX STORING POINTS
MAX STORING SPEED

MAX TIME
See chapter 26
See Chapter 26
100 days
ZERO FUNCTION
PEAK FUNCTION
UNLOAD FUNCTION
KEY BLOCK FUNCTION
TOTAL FUNCTION
AUTOZERO FUNCTION
COUNTER FUNCTION
PROGRAMMABLE RESOLUTION
PROGRAMMABLE DIGITAL FILTER
POINT POSITION
100% (all measurement range)
POSITIVE AND NEGATIVE PEAK
YES
YES
YES
YES
YES
1 –2 - 5 –10 –20 –50 - 100
0 … 5
Programmable from 0 to 5
24V DIGITAL INPUT (OPTION)
4
RS232 INTERFACE (OPTION)
MAX Cable Length 13m
RS485 INTERFACE (OPTION)
MAX Cable Length 1000m
USB port type B for data communication
USB port type A for external flash memory (on front panel)
MAX Cable Length 3.5m
NOMINAL WORKING TEMPERATURE
MAX WORKING TEMPERATURE
STORAGE TEMPERATURE
TEMPERATURE EFFECTS on the measurements 10°C
a) on zero
b) on full scale
0... +50°C
0... +50°C
-20... +70°C
±0.005%

±0.005%
PROTECTION CLASS (EN 60529)
DESKTOP CONTAINER
DIMENSIONS (AxLxP) mm
WEIGHT
REAR AND FRONT PANEL
IP40
ALLUMINIUM
86x156x213mm
about 1.9 kg
ALLUMINIUM

www.wimesure.fr • [email protected] • 01 30 47 22 00
Photos non contractuelles - Les spécications peuvent être modiées sans préavis - MP6Plus R0 - wimesure.fr • AH 2022
MP6P
P
l
l
u
u
s
s
USER GUIDE MO.MP6Plus.R7
Pag. 9
OPTION
Input Channels (up to 4)
2mV/V +/-10V, +/-5V , 4-20mA, 0-20mA, PT100
Analog Output
Current Output:
Voltage Output: max 20mA –RL min: 1kΩ
Note:
The refresh rate of the analog signals is equal to
the frequency of acquisition of the respective channels
in input.
Up to 4
4-20mA
0-5V 0-10V +/-10V +/-5V
24V Digital Input
4
Wireless Transmission of the measures
Frequency : 433MHz
Serial Communication
RS485 with protocol MODBUS and RS232
MP Supervisor communication Software
Internal Datalogger with clock Calendar
On Internal non volatile memory
Internal Datalogger with clock Calendar
USB typ
e A connector for Flash memories
Serial printer
VERSIO
N WITH HANDLE
11. PURCHASE CODES
Inputs
Power
Analog Output
Serial Output
Functions
Accessories
Digital Inputs
MP6P
X
XXX
XX
X
X
X
X
2
2 inputs
230
230 Vac
A1
1 output
S
RS232, RS485,
Printer
D
Data logger
Clock-Calendar
M
Handle
N
4 Digital Inputs
3
3 inputs
115
115Vac
A2
2 outputs
W
Wireless
Transmission
F
Datalogger
Clock-Calendar
USB Flash
Memory
4
4 inputs
24
24Vdc
A3
3 outputs
A4
4 outputs
Example: MP6P230 (MP6Plus power supply230Vac base version)
Example: MP6P224A2SM (MP6Plus 2 channels- power supply 24Vdc + 2 Analog output + Serial output + handle)
Examples: MP6P3115SF (MP6Plus 3 channels power supply 115Vac + Serial output + USB Flash Memory)
ALWAYS SPECIFY in the puchase order how to configure the input channels:
Example: CH1 = 4-20mA CH2 = 2mV/V CH3 = 10V CH4 = PT100
Note: For transducers of type potentiometer please select the channel with input +/-5V