Win PL-80690 User manual

User’s Manual
WIN Enterprises, Inc. June., 2014
1
PL-80690
Networking Appliance
Desktop Intel

Celeron

(codename Bay Trail) Network System,
Four Copper GbE, CF, SATA and mini-PCIe
User’s Manual
Version 1.0

User’s Manual
WIN Enterprises, Inc. June., 2014
2
© Copyright 2014. All Rights Reserved
Manual Edition 1.0, June, 2014
This document contains proprietary information protected by copyright. All rights are reserved;
no part of this manual may be reproduced, copied, translated or transmitted in any form or by any
means without prior written permission of the manufacturer.
The content of this document is intended to be accurate and reliable; the original manufacturer
assumes no responsibility for any inaccuracies that may be contained in this manual. The
original manufacturer reserves the right to make improvements to the products described in this
manual at any time without prior notice.
Trademarks
IBM, EGA, VGA, XT/AT, OS/2 and PS/2 are registered trademarks of International Business
Machine Corporation (IBM).
Award is a trademark of Award Software International, Inc.
Intel is a trademark of Intel Corp.
RTL is a trademark of Realtek.
VIA is a trademark of VIA Technologies, Inc.
Microsoft, Windows, Windows NT and MS-DOS are either trademarks or registered trademarks
of Microsoft Corporation.
All other product names mentioned herein are used for identification purpose only and may be
trademarks and/or registered trademarks of their respective companies.
Limitation of Liability
While reasonable efforts have been made to ensure the accuracy of this document, the
manufacturer and distributor assume no liability resulting from errors or omissions in this
document or from the use of the information contained herein.
For more information on PL-80690 or other WIN Enterprises products, please visit our website:
www.win-ent.com.
For technical support send inquiries to:
[e-mail].

User’s Manual
WIN Enterprises, Inc. June., 2014
3
Table of Contents
Chapter 1. General Information.................................................................... 4
1.1 Introduction.............................................................................................. 4
1.2 Specifications .......................................................................................... 5
1.3 Ordering Information............................................................................... 6
1.4 Packaging ................................................................................................ 6
1.5 Precautions .............................................................................................. 7
1.6 System Layout ......................................................................................... 8
1.7 Board Dimensions................................................................................... 9
Chapter 2. Connector/Jumper Configuration............................................ 10
2.1 Connector/Jumper Location and Definition........................................ 10
2.2 Connector and Jumper Setting ............................................................ 12
2.3 CompactFlash
TM
Card Socket Pin Define ............................................ 18
Chapter 3. BIOS Setup ................................................................................ 19
3.1 Quick Setup............................................................................................ 19
3.2 Entering the BIOS Setup Utility ............................................................ 20
3.3 Menu Options......................................................................................... 21
3.4 Advanced Menu ..................................................................................... 22
3.4.1 Platform function................................................................................ 23
3.4.2 NCT6791D Super IO Configuration ................................................... 24
3.4.3 NCT6791D HW Monitor ...................................................................... 25
3.4.4 IDE Configuration. .............................................................................. 26
3.4.5 USB Configuration ............................................................................. 27
3.4.6 Hardware Health Configuration......................................................... 28
3.4.7 Console Redirection........................................................................... 29
3.5 Boot Menu.............................................................................................. 30
3.6 Security Menu ........................................................................................ 31
3.7 Chipset Menu ......................................................................................... 32
3.8 Chipset Menu ......................................................................................... 35
Chapter 4. Utility & Driver Installation…………………………....……………37
Appendix A: Programming the Watchdog Timer ...................................... 39
Appendix B: Cable development kit .................Error! Bookmark not defined.

User’s Manual
WIN Enterprises, Inc. June., 2014
4
Chapter 1. General Information
1.1 Introduction
The PL-80690 is an affordable cost effective desktop platform designed for network service
applications. Built with Intel® Embedded IA components with warranty of longevity, the PL-80690
supports Intel® Celeron® Bay Trail-D, Bay Trail-I and Bay Trail-M low-voltage processors.
The platform supports onboard DDR3L memory chips with a maximum capacity of 2GB. In order
to provide the best network performance and utilization. The standard device comes equipped
with 4GB eMMC storage and interfaces including one 2.5” SATA HDD and CompactFlash™.
For network security, the PL-80690 is equipped with 4 Copper GbE, USB2.0 ports, RJ-45
console port and an optional mini-card socket with LED indicators that monitor power, storage
device activities for local system management, maintenance and diagnostics.

User’s Manual
WIN Enterprises, Inc. June., 2014
5
1.2 Specifications
CPU Intel® E3815 (Bay Trail-I) Processors
Processor System
BIOS AMI UEFI BIOS
Technology
Onboard DDR3L memory.
Memory
Capacity Up to 2GB
Expansion Expansion Slots One mini-PCIe socket via PCI-E x1.(Option)
GbE Ethernet Four Copper GbE ports, Intel I211, PCI-E x1 Ethernet
LAN bypass N/A
SATA HDD One internal 2.5” SATA HDD bayStorage
Compact Flash
Socket
one CompactFlash
TM
Type II
USB Two external USB2.0I/O
Serial One RJ45 Console port (COM1)
Power Supply Watt 40W power supply, AC to DC 12V
Form Factor Desktop
LED Power LED
HDD LED
4 pairs LEDs for 4 Ethernet ports Active/Link
status
Dimension （ W x D x
H ）
232mm (W) x 153mm (D) x 44mm (H)
(9.1W x 6” D x 1.7” H)
Operating
Temperature Operating: 0 ~ 40°C ( 32 ~ 104°F )
Storage Temperature
-20 ~ 75°C (-4 ~ 167°F)
Humidity 10 ~ 85% relative humidity, non-operating,
non-condensing
Mechanical and
Environment
Certifications CE/FCC

User’s Manual
WIN Enterprises, Inc. June., 2014
6
1.3 Ordering Information
We offer some accessories for PL-80690 appliance for customer need.
PL-8069A Desktop Intel Bay Trail E3815
Network System, 4x GbE, 1GB
onboard DDR3 Memory, 4GB eMMC
and SATA
PL-8069B Desktop Intel Bay Trail E3815
Network System, 3x GbE, 1GB
onboard DDR3 Memory, 4GB
eMMC, SATA and mini-PCIe
PL-8069C Desktop Intel Bay Trail E3815
Network System, 4x GbE, 1GB
onboard DDR3 Memory, CF, SATA
and mini-PCIe (via USB)
Optional
DK Cable development kit
CB-CO5204-00 Cross over 2M
CB-EC5200-00 Ethernet cat.5 cable
2M
CB-RJDB91-00 RJ-45 to DB-9 cable
2M
CB-IVGA01-00 VGA cable
1.4 Packaging
Please make sure that the following items have been included in the package
before installation:
1. PL-80690 Appliance
2. Quick Installation Guide (Optional)
3. Cables (Optional)
If any item of above is missing or damaged, please contact your dealer or retailer
from whom you purchased the PL-80690. Keep the box and carton for possible
future shipment or storage. After you unpack the goods, inspect and make sure
the product is intact. Do not plug the power adapter to the appliance if it appears
damaged.

User’s Manual
WIN Enterprises, Inc. June., 2014
7
Note: Keep the PL-80690 in the original packaging until you start installation.
1.5 Precautions
Please make sure you properly ground yourself before handling the PL-80690
appliance or other system components. Electrostatic discharge can be easily
damage the PL-80690 appliance.
Do not remove the anti-static packing until you are ready to install the PL-80690
appliance.
Ground yourself before removing any system component from its protective
anti-static packaging. To ground yourself, grasp the expansion slot covers or
other unpainted areas of the computer chassis.
Handle the PL-80690 appliance by its edges and avoid touching the components
on it.

User’s Manual
WIN Enterprises, Inc. June., 2014
8
1.6 System Layout
PL-80690 Front Side
Layout
PL-80690 Rear Side
Layout

User’s Manual
WIN Enterprises, Inc. June., 2014
9
1.7 Board Dimensions

User’s Manual
WIN Enterprises, Inc. June., 2014
10
Chapter 2. Connector/Jumper Configurations
2.1 Connector/Jumper Location and Definitions

User’s Manual
WIN Enterprises, Inc. June., 2014
11
CB-6902 Connectors and Jumpers:
CN1 SYSTEM FAN
CN2 CPU FAN
CN3 LPC (Pin Header)
CN4 PS2 KB/MS Pin Header (Option)
CN5 SATA Power Connector
CN6 SATA Connector
CN7 VGA (Pin Header)
CN8 COM2 Pin Header (Option)
CN9 Debug GPIO(For Test Only)
CN10 MINI-PCIE
CN11
CN12 USB Port 2 (Option)
CN13 Power Connector (Option)
CN14 USB Port 0/1
CN15 LAN1
CN16 LAN2
CN17 LAN3
CN18 LAN4
CN19 Console
CN20 DC Jack

User’s Manual
WIN Enterprises, Inc. June., 2014
12
2.2 Connector and Jumper Settings
CN1/CN2 ：
：：
： System/CPU FAN
Pin Define
1 Ground
2 +12V
3 Speed Detect
CN3 ：
：：
： LPC (Pin Header)
Pin Define Pin Define
1 +3.3V 2 AD 0
3 AD1 4 AD 2
5 AD 3 6 Frame#
7 PCIERST# 8 +5V
9 CLOCK 10 PME#
11 GND 12
13 SERIRQ 14 DRQ#
CN4 ：
：：
： PS2 KB/MS Pin Header
Pin Define Pin Define
1 KCLK 2 MCLK
3 KDAT 4 MDAT
5 N/A 6 N/A
7 PS2_GND 8 PS2_GND

User’s Manual
WIN Enterprises, Inc. June., 2014
13
9 PS2_VCC 10 PS2_VCC
CN5 ：
：：
： SATA PWR
1
2
3
4
Pin Define
1 +12V
2 GND
3 GND
4 +5V
CN6 ：
：：
： SATA Connector
Pin Signal
1 Ground
2 TXP
3 TXN
4 Ground
5 RXN
6 RXP
7 Ground
CN7 ：
：：
： VGA (Pin header)
Pin Define Pin Define
1 RED 2 GREEN
3 BLUE 4 Reserved
5 GND 6 RED PTN
7 GREEN PTN 8 BLUE RTN
9 +5V 10 GND
11 Reserved 12 SDA
13 HSYNC 14 VSYNC
15 SCL 16 Reserved

User’s Manual
WIN Enterprises, Inc. June., 2014
14
CN8 ：
：：
： COM2 pin header (Option)
Pin Define
Pin
Define
1 DCD# 6 DSR#
2 RXD# 7 RTS#
3 TXD# 8 CTS#
4 DTR# 9 RI#2
5 Ground 10 N/A
CN10: MINI PCIE
CN6
MINI_PCIE
WAKE#
13.3V 2
RESERVED
3
RESERVED
5
CLKREQ#
7
GND
9
REFCLK-
11
REFCLK+
13
GND
15
RESERVED
17
RESERVED
19
GND
21
PERN0
23
PERP0
25
GND
27
GND
29
PETN0
31
PETP0
33
GND
35
RESERVED
37
RESERVED
39
RESERVED
41
RESERVED
43
RESERVED
45
RESERVED
47
RESERVED
49
RESERVED
51 +3.3V 52
GND 50
+1.5V 48
LED_WPAN# 46
LED_WLAN# 44
LED_WWAN# 42
GND 40
USB_D+ 38
USB_D- 36
GND 34
SMB_DATA 32
SMB_CLK 30
+1.5V 28
GND 26
+3.3VAUX 24
PERST# 22
RESERVED 20
GND 18
RESERVED 16
RESERVED 14
RESERVED 12
RESERVED 10
RESERVED 8
1.5V 6
GND 4
Pin Define Pin Define
1 WAKE# 2 3.3V
3 Reserved 4 GND
5 Reserved 6
1.5V
7
CLKREQ# 8 Reserved
9
GND 10 Reserved
11
REFCLK- 12 Reserved
13
REFCLK+ 14 Reserved
15
GND 16 Reserved
17
Reserved 18 GND
19
Reserved 20 Reserved
21
GND 22 PERST#
23
PERN0 24 +3.3VAUX

User’s Manual
WIN Enterprises, Inc. June., 2014
15
25
PERP0 26 GND
27
GND 28 +1.5V
29
GND 30 SMB_CLK
31
PETN0 32 SMB_DATA
33
PETP0 34 GND
35
GND 36 USB_D-
37
Reserved 38 USB_D+
39
Reserved 40 GND
41
Reserved 42 LED_WWAN#
43
Reserved 44 LED_WLAN#
45
Reserved 46 LED_WPAN#
47
Reserved 48 +1.5V
49
Reserved 50 GND
51
Reserved 52 +3.3V
CN14 ：
：：
： USB (Port 0/1) Connector
Pin Define Pin Define
1 +5V 2 DATA0-
3 DATA0+ 4 GND
5 +5V 6 DATA1-
7 DATA1+ 8 GND
CN15~18 ：
：：
： LAN RJ-45 Connector
Pin Define
1 TX+
2 TX-

User’s Manual
WIN Enterprises, Inc. June., 2014
16
3 RX+
4 Chassis Ground
5 Chassis Ground
6 RX-
7 Chassis Ground
8 Chassis Ground
D1: Speed indicated LED
1 Gbps GREEN
100 Mbps YELLOW
D2 :Link/Activity LED
Link GREEN
Activity BLINKING
CN19 ：
：：
： COM1 (Console) Connector
RJ45
Pin Define
1 CTS#
2 DTR#
3 TXD#
4 GND
5 GND
6 RXD#
7 DSR#
8 RTS#
CN20 ：
：：
： DC +12V Power Jack (2Pin)
11
22
Pin Define Pin Define
1 +12V 2 GND

User’s Manual
WIN Enterprises, Inc. June., 2014
17
Jumper Settings
JP1 ：
：：
： Clear CMOS
Pin Setting
1-2 Normal
Operation
2-3 Clear CMOS

User’s Manual
WIN Enterprises, Inc. June., 2014
18
JP2 ：
：：
： Watching Dog Function Select
Pin Setting
1-2 For Reset
2-3 For LAN Bypass
2.3 CompactFlash
TM
Card Socket Pin Define
CompactFlash
TM
card is a small removable mass storage device. It can provide
complete PCMCIA-ATA functionality and compatibility plus True IDE functionality
compatible with ATA/ATAPI-4.
CompactFlash
TM
storage products are solid state form factor, it means they
contain no moving parts. Thus, they provide users with much greater protection
of the data than conventional magnetic disk device.
Pin Assignment Pin Assignment Pin Assignment Pin Assignment Pin Assignment
1 Ground 11 Ground 21 D00 31 D15 41 RESET
2 D03 12 Ground 22 D01 32 CS 42 ORDY
3 D04 13 VCC 23 D02 33 NC 43 DREG
4 D05 14 Ground 24 WP 34 IOR 44 DACK
5 D06 15 Ground 25 NC 35 IOW 45 LED
6 D07 16 Ground 26 NC 36 WE 46 BVD
7 CS 17 Ground 27 D11 37 RDY/BSY 47 D08
8 Ground 18 A02 28 D12 38 VCC 48 D09
9 Ground 19 A01 29 D13 39 SCSE 49 D10
10 Ground 20 A00 30 D14 40 NC 50 Ground

User’s Manual
WIN Enterprises, Inc. June., 2014
19
Chapter 3. BIOS Setup
The ROM chip of your PL-80690 board is configured with a customized Basic
Input/Output System (BIOS) from AMI BIOS. The BIOS is a set of permanently
recorded program routines that give the system its fundamental operational
characteristics. It also tests the computer and determines how the computer
reacts to instructions that are part of programs.
The BIOS is made up of code and programs that provide the device-level control
for the major I/O devices in the system. It contains a set of routines (called
POST, for Power-On Self Test) that checks the system when you turn it on. The
BIOS also includes CMOS Setup program, so no disk-based setup program is
required. CMOS RAM stores information for:
Date and time
Memory capacity of the appliance
Type of display adapter installed
Number and type of disk drives
The CMOS memory is maintained by a battery installed on the PL-80690 board.
By using the battery, all memory in CMOS can be retained when the system
power switch is turned off. The system BIOS also enables an easy way to
reload the CMOS data when you replace the battery, etc.
3.1 Quick Setup
In most cases, you can quickly configure the system by choosing the following
main menu options:
1. Choose “Exit” “Load Optimal Defaults” from the main menu. This loads
the setup default values from the BIOS Features Setup and Chipset Features
Setup screens.
2. Choose “Main” & “Advanced” from the main menu. This option lets you
configure the date and time, hard disk type, floppy disk drive type, primary
display and more.
3. In the main menu, press F4 (“Save Changes and Exit”) to save your changes
and reboot the system.
3.2 Entering the BIOS Setup Utility
Use the BIOS Setup program to modify the system parameters to reflect the

User’s Manual
WIN Enterprises, Inc. June., 2014
20
options installed in your system and to customize your system. For example, you
should run the Setup program after you:
Receive an error code notification at startup
Install another disk drive
Use your system after not having used it for a long time
Find the original setup missing
Replace the battery
Change to a different type of CPU
Run the AMI Flash program to update the system BIOS
Run the BIOS Setup program after you turn on the system. On-screen
instructions explain how to use the program.
Enter the BIOS Setup program’s main menu as follows:
1. Turn on or reboot the system. After the BIOS performs a series of
diagnostic checks, the following message appears:
“Press DEL to enter SETUP”
2. Press the <DEL> key to enter BIOS Setup program. The main menu
appears:
3. Choose a setup option with the arrow keys and press <Enter>. See the
following sections for a brief description of each setup option.