Windcave SCR200MO Installation instructions

SCR200MO Hardware Guide
Version 0.5

Procedure: Number 56 – SCR200MO Hardware Guide
Date: June 2020
Approved by: Implementation Manager
Copyright
© Copyright 2020, Windcave Inc.
www.windcave.com
All rights are reserved. No part of this work may be reproduced or copied in any form or by any means,
electronic or mechanical, including photocopying, without the express written permission of Windcave
Inc.
Proprietary Notice
The information described in this document is proprietary and confidential to Windcave Inc. Any
unauthorised use of this material is expressly prohibited except as authorised by Windcave Inc. in
writing.
This document is uncontrolled when printed

Procedure: Number 56 – SCR200MO Hardware Guide
Date: June 2020
Approved by: Implementation Manager
Document Revision Information and Amendments
All amendments are to be identified and the manual updated, noting the amendment on this
amendment page.
Version Date Section Revision Information Amended by
0.1
2020/05/25
All
Initial Draft
KH
0.2 2020/06/08 1
2
Updated introduction and description of
device
Updated hardware overview, power
requirements, temperature ratings and
compliance & standards
KH
0.3 2020/06/10 3
Added note about using non-metallic
mounting plate
KH
0.4
2020/06/10
1
Updated introduction
KH
0.5
2020/06/12
2
Formatting update
KH
Related Documents
Document Title Link/Location

Procedure: Number 56 – SCR200MO Hardware Guide
Date: June 2020
Approved by: Implementation Manager
SCR200MO Hardware Guide Version: 0.5
Page | 3of 12
Contents
1Overview................................................................................................................................................................ 4
1.1 Introduction ................................................................................................................................................ 4
1.2 Hardware Models......................................................................................................................................4
1.3 Connectivity................................................................................................................................................ 4
2SCR200MO ........................................................................................................................................................... 5
2.1 Hardware Overview...................................................................................................................................5
2.1.1 Physical Link Interface......................................................................................................................... 5
2.1.2 Power Requirements............................................................................................................................ 5
2.1.3 Operating & Storage Temperature Ratings ..................................................................................... 5
2.1.4 Standards & Compliance..................................................................................................................... 6
2.1.5 Additional Comments .......................................................................................................................... 6
2.1.5.1 FCC Part 15 User Information................................................................................................... 6
2.2 SCR200MO Dimensions ..........................................................................................................................7
3Machine Face & Cut-out Dimensions.............................................................................................................. 9
3.1 SCR200MO ................................................................................................................................................. 9
4Installation ..........................................................................................................................................................10
5Maintenance.......................................................................................................................................................11
5.1 Tradeouts & Deactivation Process ......................................................................................................11
5.2 Cleaning Instructions..............................................................................................................................11
6Document Control Procedure.........................................................................................................................12

Procedure: Number 56 – SCR200MO Hardware Guide
Date: June 2020
Approved by: Implementation Manager
SCR200MO Hardware Guide Version: 0.5
Page | 4of 12
1Overview
1.1 Introduction
The Windcave SCR200MO solution is a contactless secure card reader. It can act as an accessory to
the SCR200F for the handling of contactless reads, or act as a standalone contactless payment
solution.
The standalone option provides a simple solution for accepting contactless payments in an unattended
card present environment; where only contactless payments are required. Integration of the SCR200MO
standalone mode utilizes the same global Serial API specification accepted by the SCR solutions.
Windcave develops and owns the hardware design, intellectual property and processor platform to
ensure end to end accountability from card read to bank card provider.
1.2 Hardware Models
Model
Description
SCR200MO Contactless Secure Card Reader
1.3 Connectivity
The connector for the device is on the rear of the unit, this connector is used to connect the SCR200MO
to other Windcave secure card readers.

Procedure: Number 56 – SCR200MO Hardware Guide
Date: June 2020
Approved by: Implementation Manager
SCR200MO Hardware Guide Version: 0.5
Page | 5of 12
2SCR200MO
2.1 Hardware Overview
2.1.1 Physical Link Interface
Refer to connectivity 1.3
2.1.2 Power Requirements
The device accepts DC regulated from +9V to +45V SELV (Safety Extra Low Voltage).
2.1.3 Operating & Storage Temperature Ratings
Supported
Recommended
Operating
-20°C/-4°F to 75°C/167°F -20°C/-4°F to 45°C/113°F
Storage
-30°C/-22°F to 80°C/176°F 10°C/50°F to 30°C/86°F
Note: Storing and using your device for extended periods outside of the recommended temperature range could shorten its service life.
•Modular Design
•Secure crypto MCU designed for POS
applications
•Hardware accelerated encryption (Triple
DES, RSA and AES) and a CRC engine
•Contactless Reader
•Dedicated tamper grid

Procedure: Number 56 – SCR200MO Hardware Guide
Date: June 2020
Approved by: Implementation Manager
SCR200MO Hardware Guide Version: 0.5
Page | 6of 12
2.1.4 Standards & Compliance
2.1.5 Additional Comments
2.1.5.1 FCC Part 15 User Information
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions:
1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause
undesired operation.
Changes or modifications not expressly approved by the party responsible for compliance could void
the user’s authority to operate the equipment.
•EMVCo L1 Contactless
•L2 Contactless
•PCI PTS V5.x: SRED (Secure Reading and
Exchange of Data)
•FCC
•AusPayNet
•TQM
•RoHS

Procedure: Number 56 – SCR200MO Hardware Guide
Date: June 2020
Approved by: Implementation Manager
SCR200MO Hardware Guide Version: 0.5
Page | 7of 12
2.2 SCR200MO Dimensions

Procedure: Number 56 – SCR200MO Hardware Guide
Date: June 2020
Approved by: Implementation Manager
SCR200MO Hardware Guide Version: 0.5
Page | 8of 12

Procedure: Number 56 – SCR200MO Hardware Guide
Date: June 2020
Approved by: Implementation Manager
SCR200MO Hardware Guide Version: 0.5
Page | 9of 12
3Machine Face & Cut-out Dimensions
3.1 SCR200MO
Recommended cut out dimensions for customer equipment. Please note that this plate is not supplied
as part of the Windcave Hardware and is the responsibility of the customer to arrange their selected
mounting method. All non-dimensioned lengths are subject to individual customer machine fronts.
Customer mounting plate must be a non-metallic material.

Procedure: Number 56 – SCR200MO Hardware Guide
Date: June 2020
Approved by: Implementation Manager
SCR200MO Hardware Guide Version: 0.5
Page | 10 of 12
4Installation
#
Description
Default QTY
1 SCR200MO-A 1
2 TAPE SCR200MO FRONT CASE MOUNTING VHB 1
3 CUSTOMER SUPPLIED EQUIPMENT, NOT PROVIDED BY WINDCAVE INC. 1

Procedure: Number 56 – SCR200MO Hardware Guide
Date: June 2020
Approved by: Implementation Manager
SCR200MO Hardware Guide Version: 0.5
Page | 11 of 12
5Maintenance
5.1 Tradeouts & Deactivation Process
In the event that the SCR200MO unit needs to be swapped out or deactivated, please follow
instructions below.
1) Call Windcave Support to log a ticket. Please provide the following information.
1. Serial Number of SCR200MO.
2. Brief description of fault / reason for deactivation.
3. Contact Name.
4. Contact Phone Number.
5. Shipping Address (for replacement if needed).
2) Physically remove the device(s). At next communication with the host the device will be marked as
removed.
3) Ship the device(s) back to Windcave.
5.2 Cleaning Instructions
The external face of the SCR200MO device should be carefully cleaned on a regular basis. This is to
ensure that the front plate is free of dirt and solvents which could damage the device or prevent users
from using the device as intended. Windcave recommend cleaning the device with a damp cloth or mild
soap solution. Do not use any solvents as this may damage the device surface.

Procedure: Number 56 – SCR200MO Hardware Guide
Date: June 2020
Approved by: Implementation Manager
SCR200MO Hardware Guide Version: 0.5
Page | 12 of 12
6Document Control Procedure
Document Owner
Implementation Consultant
Process Owner
Implementation Manager
Document Approver
Implementation Manager
Distribution List
Implementations, Global Trainer, Service Delivery Manager, Hardware
Engineer
Audit Date
Audit Frequency
Annually
This document will be reviewed in accordance with the audit frequency, but may also be updated to
reflect changes as required.