Windoware MOTOWARE User manual

MOTOWARE
MOTOWARE
MOTOWARE
motoware
MOTOWARE
MOTOWARE
MOTOWARE
VERTICAL AWNING
MOTOR INSTRUCTIONS
Favourite
Position
Electronic
Limit
433 MHZ RF Communication
Electronic Limits
Favorite Position
Fabric Tensioning Function
Features
BLINDS & AWNINGS
Motoware Automation Programming Instructions | Vertical Awning Motor
PLEASE READ OUR INSTRUCTIONS ON OUR 15CH REMOTE BEFORE WORKING ON THE MOTORS
Fabric Tensioning
Function

MOTOWARE
MOTOWARE
MOTOWARE
motoware
MOTOWARE
MOTOWARE
MOTOWARE
BLINDS & AWNINGS
Motoware Automation Programming Instructions | Vertical Awning Motor
1. INTRODUCTION
P1 button on motor head
1
2
3
1
2
3
Technical Information
RTS
4-Core Standard
Curtain Track Motor
04819
100kg Curtain Motor RTS 75/20
04820
100kg Curtain Motor 4-Core 75/20
RTS
Curtain Track Motor
Blue = Neutral
Black = Direction 1
Brown = Direction 2
Green = Earth
Wired
Yellow
Blue = Neutral
Brown = Live
Green = Earth
Yellow
Track Motor Specifications
windoware
designer collection
19
Motor
Track
235
52
34
22
8.2
30
1.8
Specifications 04820 4-Core 04819 RTS
Rated Curtain Weight: *100 Kilograms
Rated Input Power : 75 Watts 75 Watts
Open/close Speed: 20 (cm/sec) 20 (cm/sec)
Input Rated Voltage: 230 Volts 230 Volts
Frequency: 50 Hertz 50 Hertz
Rated Current: 0.34 Amps 0.34 Amps
Running Time: 4 Minutes 4 Minutes
Protection Class: IP20 IP20
Maximum Range Of Revolutions: ∞ ∞
Track Length: ≥12 Metres 12 Metres
Motor Weight: 1.1 Kilograms 1.1 Kilograms
*100 Kilograms
≥
50
windoware
designer collection
IMPORTANT
Ensure blind is installed with power lead pointing towards
the ground - otherwise water will run into the motor.
!

MOTOWARE
MOTOWARE
MOTOWARE
motoware
MOTOWARE
MOTOWARE
MOTOWARE
BLINDS & AWNINGS
Motoware Automation Programming Instructions | Vertical Awning Motor
2.1 Pair motor with controller
2. INITIAL SET-UP
(Complete the pairing process in less than 10 seconds)
Select channel on controller.
IMPORTANT
Please see our separate
instructions on the 15 Channel
Remote for further information
if required.
!
Press P2 on existing controller.

Release button immediately after
1 x BEEP
Press P2 on existing controller.

Release button immediately after
1 x BEEP
Press the UP button.

Release button immediately after
2 x BEEP
Motor confirmation
3 x JOG
Switch power on the motor.

BLINDS & AWNINGS
Motoware Automation Programming Instructions | Vertical Awning Motor
2.2 Check motor direction
To check travel direction of your blind, press UP
or DOWN on the controller. Press STOP if your
blind is still moving.
If your motor is traveling in correct way please skip
to next step (3.1).
To reverse your blind direction, hold the
P1 button on the motor head approximately for 5 seconds.
Release button immediately after
1 x LONG BEEP
IMPORTANT
Damage to your blind may occur when operating motor
prior to setting limits. Attention should be given.
!Motor confirmation
1 x JOG
P1 button on
motor head

MOTOWARE
MOTOWARE
MOTOWARE
motoware
MOTOWARE
MOTOWARE
MOTOWARE
BLINDS & AWNINGS
Motoware Automation Programming Instructions | Vertical Awning Motor
3. SET THE LIMITS
3.2 Set the upper limit
3.1 Enter limit setting mode
3.3 Set the lower limit
Move your blind to the desired highest
location by pressing the UP or DOWN
button on the controller. Press STOP when
you have reached your preferred position.
Move your blind to the desired highest
location by pressing the UP or DOWN
button on the controller. Press STOP when
you have reached your preferred position.
*Hint: Press the P2 button as the blind is rolling up the
motor will step, this will help to improve accuracy.
*Hint: Press the P2 button as the blind is rolling up the
motor will step, this will help to improve accuracy.
Press the STOP button on
the remote 5 times.
Press the STOP button on
the remote 5 times.
UPPER LIMIT SET
LOWER LIMIT SET
IMPORTANT
Cycle your outdoor blind up and down prior to setting limits to settle fabric.
!
Motor confirmation
1 x BEEP
Motor confirmation
1 x BEEP
Motor confirmation
1 x LONG BEEP
1 x JOG 
Press the P2 button on the remote Press the P2 button on the remotePress the UP button on the remote
Motor confirmation
4 x BEEP
1 x LONG BEEP
1 x JOG
Motor confirmation
4 x BEEP
1 x LONG BEEP
1 x JOG

MOTOWARE
MOTOWARE
MOTOWARE
motoware
MOTOWARE
MOTOWARE
MOTOWARE
BLINDS & AWNINGS
Motoware Automation Programming Instructions | Vertical Awning Motor
4. FAVOURITE POSITIONING
4.1 Set a favourite position
4.2 Make your blind go to the “favourite position” that’s been set up
4.3 Delete favourite position
Move your blind to the desired position by pressing the UP or DOWN button on the controller.
Move your blind to your favourite position by holding down STOP (as per 4.2).
Hold STOP on controller until motor begins moving, then release.
Press STOP on controller 5 times.
(Motor will beep each time).
Press STOP on controller 5 times.
(Motor will beep each time).
Motor confirmation
1 x LONG BEEP
1 x JOG
Motor confirmation
1 x LONG BEEP
1 x JOG
Note: If you’re using a grouped channel all
blinds will be sent to their favourite position
(Ideal for leveling multiple blinds at a half way point)

MOTOWARE
MOTOWARE
MOTOWARE
motoware
MOTOWARE
MOTOWARE
MOTOWARE
BLINDS & AWNINGS
Motoware Automation Programming Instructions | Vertical Awning Motor
5.1 Adding a new controller or copying a channel
5.2 Deleting a controller or channel
ADDING OR REMOVING
CONTROLLERS AND CHANNELS
5.
A= Existing controller or channel (to keep)
B= Controller or channel to add or remove
A= Existing controller or channel (to keep)
B= Controller or channel to add or remove
Press P2 on existing controller.

Release button immediately after
1 x JOG 
Press P2 on existing controller.

Release button immediately after
1 x JOG 
Press P2 on existing controller.

Release button immediately after
1 x JOG 
Press P2 on existing controller.

Release button immediately after
1 x JOG 
Press P2 on new controller.

Release button immediately after
2 x JOG 
Press P2 on new controller.

Release button immediately after
2 x JOG 
Motor confirmation
1 x BEEP
Motor confirmation
1 x BEEP
Motor confirmation
1 x BEEP
Motor confirmation
1 x BEEP
Motor confirmation
3 x BEEP
Motor confirmation
3 x BEEP

MOTOWARE
MOTOWARE
MOTOWARE
motoware
MOTOWARE
MOTOWARE
MOTOWARE
BLINDS & AWNINGS
Motoware Automation Programming Instructions | Vertical Awning Motor
6. SAFETY INSTRUCTIONS
CAUTION
• Do not expose to moisture or extreme temperatures.
• Do not allow children to play with this device.
• Use or modification outside the scope of this instruction manual will void warranty.
• Installation and programming to be performed by a suitably qualified installer.
• For use within tubular blinds.
• Ensure correct crown and drive adaptors are used for the intended system.
• Keep antenna straight and clear from metal objects
• Do not cut the antenna.
• Do not expose the motor to water or install in humid or damp environments.
• Motor is to be installed in horizontal application only.
• Do not drill into motor body.
• The routing of cable through walls shall be protected by isolating bushes or grommets.
• Ensure power cable and aerial is clear and protected from moving parts.
• If cable or power connector is damaged do not use.
WARNING: Important safety instructions to be read before installation.
Incorrect installation can lead to serious injury and will void manufacturer’s liability and warranty.
Important safety instructions to be read prior to operation.
• It is important for the safety of persons to follow the enclosed instructions. Save these instructions for future reference.
• Persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and
knowledge should not be allowed to use this product.
• Keep remote controls away from children.
• Frequently inspect for improper operation. Do not use if repair or adjustment is necessary.
• Keep motor away from acid and alkali.
• Do not force the motor drive.
• Keep clear when in operation.

BLINDS & AWNINGS
MOTOWARE
MOTOWARE
MOTOWARE
motoware
MOTOWARE
MOTOWARE
MOTOWARE
40 Parramatta Road, Underwood QLD 4119
www.windoware.com.au
1300 735 401