Wine Master WINEOUT25X User manual

Installation and
operating instructions
(Keep it in a safe
place).
WINEOUT25X
INFORMATION ON THE RATING PLATE ON THE APPLIANCE :
1. Model : …………………………….....
2. Serial number : …………………………..
3. Date of purchase : …………………………
08/03/2023

VERSION 5 08.03.2023
USER GUIDE WINE OUT25X Page 3
Contents
2. SPACE PLANNING......................................................................................6
2.1. Warm air discharge .................................................................................6
2.2. Cellar insulation ......................................................................................7
2.2.1. Wall, ceiling and floor insulation.................................................................8
2.2.2. The door ...............................................................................................9
2.2.3. Insulation of other elements .....................................................................9
3. INSTALLING THE WINEMASTER® AIR CONDITIONER ..............................10
3.1. Installation of the water outlet and the power cable.............................13
4. THERMOSTAT AND ELECTRICAL CONNECTION.........................................14
4.1. Winemaster Connect .............................................................................14
4.2. Thermostat connection..........................................................................14
4.3. Connecting the WINEMASTER® air conditioner .....................................15
4.4. Setting the temperature of the WINEMASTER® COOLER .......................15
4.5. Setting the unit of measurement ...........................................................16
5. CARE AND MAINTENANCE OF THE WINEMASTER®AIR CONDITIONER ....17
5.1. Filter change .........................................................................................17
5.2. Condensate drain pipe ...........................................................................17
6. WARRANTY..............................................................................................18
6.1. Legal warranty ......................................................................................18
6.2. 2-years contractual warranty ................................................................18
6.3. Conditions of application of the warranty..............................................18
6.4. Exclusions and limits of the warranty....................................................18

VERSION 5 08.03.2023
USER GUIDE WINE OUT25X Page 4
Introduction
You have just acquired a WINEMASTER® air conditioner and we thank you for your
confidence.
From its conception to its marketing, everything has been done to offer you an exclusive
and high quality product. The result of the work of a whole team which finds in this
philosophy an always greater motivation to satisfy you, we hope that your WINEMASTER®
air conditioner will bring you optimal conditions of conservation and ageing of your wines
for an incomparable pleasure.
Because the customer is at the heart of all our thoughts, we wish to assist you in your
first steps and guide you towards an optimal use of your air conditioner on a daily basis.
In this manual, you will find technical information and instructions for an easy installation
and an optimal functioning of your appliance.
THE WINEMASTER® TEAM.

VERSION 5 08.03.2023
USER GUIDE WINE OUT25X Page 5
General Features
WINE OUT25X
Weight of the device
45kg
Device dimensions (mm)
H.700 X W.503 X D.498
Temperature setting
Preset à 12°C, ajustable entre 8 et 18°C *
Max outdoor temperature
40°C **
Cooling capacity
550 W à 15°C **
•Electric power supply
230/240V-50 Hz + 3 m of cable
•Electrical power in cooling mode
550 W
•Electrical power in heating mode
250 W
The circuit breaker rating must be 16 Amperes.
* With insulation appropriate for the temperature and volume of the room.
** As a result of power reduction depending on the outdoor temperature, the device may lose its capacity
to maintain 12°C if the outdoor temperature approaches 40 °C.
In case of too frequent thermal cut-out, the compressor can be damaged prematurely.
Technical dimensional drawing

VERSION 5 08.03.2023
USER GUIDE WINE OUT25X Page 6
2. SPACE PLANNING
The air conditioner is installed outside the wine cellar (in another room or outside) on the wall using the
two brackets provided. It can also be placed on the floor.
For a proper operation, the unit discharges air to the outside at about 15°C above the intake temperature.
This air is discharged through the grilles located at the back and bottom of the machine. Be careful not to
block these grilles.
→The suction and the rejection of the air allowing its cooling is done by means of two ducts
crossing the wall.
2.1.Warm air discharge
If the WINEMASTER® air conditioner rejects hot air in a room (air conditioner installed in a room), this one
must be well ventilated :
-Maximum temperature and not permanent ≤ 40°C
-Ideal temperature ≈22.5°C.
→It is better to evacuate the hot air out of the room if possible, by installing the air conditioner outside.
Indeed, it is preferable to install the air conditioner outside in order to have a renewal of the air. Moreover,
this will prevent the unit from overheating.
-Do not obstruct the ducts (risk of
overheating the unit)
-Maximum length of both ducts in total:
1m in a straight line
-Do not reduce the section of the ducts
Top view
1. THE AIR IN THE CELLAR IS EVACUATED
2. CELLAR AIR INLET
3. OUTSIDE AIR EXHAUSTED
4. OUTSIDE AIR INLET
5. WINE TANK
6. REJECT ROOM OR OUTSIDE THE HOUSE
25°C
40°C
1
2
4
3
5
6

VERSION 5 08.03.2023
USER GUIDE WINE OUT25X Page 7
2.2.Cellar insulation
It is determining for a good operation of the WINEMASTER® air conditioner. An adequate insulation will
contribute to ensure a better stability of the temperature and hygrometry. The table below (choice of
insulation) makes it possible to determine the type and the thickness of insulation necessary according to
the interior volume of the cellar and the model of WINEMASTER® air conditioner, for an interior temperature
of 12°C. You can also carry out a calculation which corresponds to your cellar on our website:
www.winemaster.fr/en/project/
Insulation continuity
The insulating materials should preferably be assembled:
- By interlocking the panel rabbets
- By gluing the panels together
→OBJECTIVE: To avoid parasitic entries of heat and humidity which would harm their
regulation.
Cross section
1. WALL
2. INSULATION
3. FLOOR
4. FINISHED FLOOR
5. CEILING
6. INSULATED DOOR
IMPORTANT
The validity of the warranty of the WINEMASTER® air conditioner is linked to the strict respect of the
values of the table "Choice of insulation" for all the walls of the cellar (including floor, ceiling and
door) as well as to the perfect continuity of the insulation and to an installation in conformity with
the notice.
2

VERSION 5 08.03.2023
USER GUIDE WINE OUT25X Page 8
Choice of insulation
Volume of air-
conditioned
room (m3)
Thickness of expanded
polystyrene (mm)
(λ= 0.044 W.m-1.C-1)
Thickness of extruded
polystyrene (mm)
(λ= 0.030 W.m-1.C-1)
Thickness of polyurethane
(mm)
(λ= 0.025 W.m-1.C-1)
6
40
30
30
8
50
40
30
10
60
40
40
12
70
50
40
14
70
50
40
16
80
60
50
18
90
60
50
20
90
70
60
22
100
70
60
24
110
70
60
2.2.1. Wall, ceiling and floor insulation
Choice of insulating panels
The manufacturers offer different insulating panels:
- Insulation alone,
- The "complexes": insulation covered with a facing (plaster, mineral...),
- Sandwiches: insulation lined on each side with a wood or plaster panel.
Important: the coating protects the insulation from shocks and therefore guarantees its durability.
Avoid using mineral fiber insulation (glass wool, rock wool, etc. ....) because they can become loaded
with moisture and lose their insulating power, as well as thin-film insulation, which is not effective in cold
weather.
DID YOU KNOW ?
Some insulating materials are damaged by rodents (mice, rats, ...). It is therefore necessary to check
that the walls of the cellar do not have any holes allowing rodents to reach the insulation. These
insulations will be covered, on the internal face of the cellar, with a protective facing.
→Polyurethane is an insulator which, because of its chemical composition, is not attacked by
rodents.
Floor insulation
The cellar floor must be able to support the shelves and the stored wine. It is therefore necessary to choose
an insulation with sufficient compressive strength.
Resistance to perforation (especially at the foot of the shelves) is achieved by :
- "Complex" insulating panels coated on their upper side with a sufficiently resistant panel.
- An insulating material lined with a chipboard panel (thickness about 15 mm), or any other
suitable covering (screed and slab for example).

VERSION 5 08.03.2023
USER GUIDE WINE OUT25X Page 9
2.2.2. The door
It contributes to the continuity of the insulation. Two possible solutions:
- Insulate the existing door with the same type of insulation as for the cellar walls. Insert
a seal (in foam for example) between the door and the frame of the door, on all its periphery.
- Use a WINEMASTER®insulated door, filled with polyurethane foam with a seal on all its
periphery.
Top view
1. ISOTHERMAL DOOR
2. INSULATION
3. SEALING
2.2.3. Insulation of other elements
Do not put a wine cabinet or freezer, which produce heat, in the cellar. Central heating pipes
should be re-insulated when moving into the cellar.

VERSION 5 08.03.2023
USER GUIDE WINE OUT25X Page 10
3. INSTALLING THE WINEMASTER® AIR CONDITIONER
THE UNIT MUST BE INSTALLED IN ACCORDANCE WITH NATIONAL ELECTRICAL
INSTALLATION REGULATIONS.
Make sure you choose the right location for the air conditioner :
- Choose the ideal location: shortest possible duct length
- No obstacles in front of the ventilation (facilitates the circulation of the cold air flow)
- The support or the floor must be level and not transmit vibrations
Cut
1. OUTSIDE WALL
2. INSULATED WALL
3. INSULATED SHEATH
PROVIDED
4. AIR CONDITIONER
5. INSULATED DOOR
Required material (not delivered)
Material included in the package
Pipes 45cm

VERSION 5 08.03.2023
USER GUIDE WINE OUT25X Page 11
Outside
The template provided allows you to preview the size of
the machine and draw the holes to be drilled. Please,
note that if the appliance is placed on the floor, the
template is intended for the minimum height of the feet.
Place the drilling template against the exterior wall where the WINEMASTER® air conditioner will be
installed
Outside
Mark the locations of the mounting holes and fixation
holes
Drill the marked holes
1
2
3

VERSION 5 08.03.2023
USER GUIDE WINE OUT25X Page 12
Unfold the brackets and fix them to the wall
Fix the air conditioner on the brackets :
- Place the air conditioner on the brackets
- Screw the 4 M8 nuts and washers (13 mm
wrench)
Insert the pipes on the air conditioner
4
5
6

VERSION 5 08.03.2023
USER GUIDE WINE OUT25X Page 13
3.1.Installation of the water outlet and the power cable
1. DRAINING HOSE Ø19mm X 1.5 meter.
- The condensation water is drained through a flexible hose integrated in the air conditioner.
- The drainage is done by gravity. It can be connected to a sewage system or the water can be drained
on the floor.
THE DRAIN HOSE MUST NOT BE PINCHED OR
LOOPED UPWARDS !
The drip tray may overflow if the hose is not
directed downwards
Warning :
After transport or handling, wait 24 hours before connecting the air
conditioner.
If the power cable is damaged, it must be replaced by the manufacturer,
its service department or similarly qualified persons in order to avoid a
hazard .

VERSION 5 08.03.2023
USER GUIDE WINE OUT25X Page 14
4. THERMOSTAT AND ELECTRICAL CONNECTION
4.1.Winemaster Connect
The machine is already equipped with the device for the Winemaster Connect application. This must be
connected to the digital card with an Ethernet cable (classic 6). The cable is designed to be routed through
the cable duct behind the machine. The cover must be opened with the power off.
The application allows the user to follow the temperature evolution of his cellar. It also allows the after-
sales service to quickly identify the source of a possible problem.
4.2.Thermostat connection
An external thermostat is supplied with the machine. This can be placed inside or outside the air-conditioned
room. It can also be linked to the Winemaster Connect application.
A complete manual is provided with the thermostat, for its installation and its integration with Winemaster
Connect.
The thermostat can be placed in front of a wall or through a wall. The sensor should be placed towards the
return air area. It is recommended that the end of the sensor does not touch the wall and is in the airflow.
The thermostat has a 5-wire male connector and the machine has a female connector. The thermostat must
be connected to the machine using this cable. The connection of the thermostat MUST BE MADE WITHOUT
VOLTAGE
The thermostat displays the air temperature inside the cellar, within a range of 2°C. This variation in air
temperature results in a smaller variation in wine temperature due to the thermal inertia of the liquid. The
thermostat is set at the factory to a set temperature of 12°C. When the air conditioner is put into service,
this temperature should be checked and, if necessary, changed by following the procedure below.

VERSION 5 08.03.2023
USER GUIDE WINE OUT25X Page 15
4.3.Connecting the WINEMASTER® air conditioner
The electrical connection of the machine
is made using the connection cable
The socket must be accessible after installation.
On ignition, the thermostat
displays the cellar’s temperature.
The thermostat is locked and displays
« Loc » if a touch is effectued on the display.
- If the cellar temperature is higher than the thermostat setting: the air conditioner starts after 2 minutes
- If the cellar temperature is lower than the thermostat setting: the compressor does not start. Only the
fan on the cellar side runs.
4.4.Setting the temperature of the WINEMASTER® COOLER
The set temperature is set on the thermostat :
If the power cable is damaged, it must be replaced by the manufacturer,
its service department or similarly qualified persons in order to avoid any
danger.
Decrease the temperature
Validate the temperature
Increase the temperature
Press the upper symbol
Unlock the thermostat by making a long
press on the symbol
Press the upper symbol

VERSION 5 08.03.2023
USER GUIDE WINE OUT25X Page 16
Setting the unit of measurement
The temperature measurement unit can be changed to °C or °F :
Press once on the symbol
Unlock the thermostat by making a long
press on the symbol
Previous menu
Validate menu
Next menu
Select the PRO menu and
press the middle symbol
Select menu /5 and press
the middle symbol
Select 0 for °C or 1
for °F, and confirm
with the symbol
After a few seconds, the display
returns to the cellar temperature
with the new unit of measurement
selected

VERSION 5 08.03.2023
USER GUIDE WINE OUT25X Page 17
5. CARE AND MAINTENANCE OF THE WINEMASTER®AIR
CONDITIONER
5.1. Filter change
Open the honeycomb grid
Clean the WINEMASTER filter and the
honeycomb grid
Close the grid properly
TO DO FOR THE FILTER :
- Control: every 3 months
- Clean: 1 time per year
→DIRTY FILTER = DAMAGED AIR CONDITIONER
TO DO FOR THE EXTERNAL GRILLS :
- Cleaning (foliage...) : regular (according to use)
TO DO FOR THE DRAIN PIPE :
-check that it is not obstructed, clean if necessary.
5.2.Condensate drain pipe
Be sure to check (possible pinching) and clean this hose at least once a year. As a reminder, this hose
should not be pinched or looped up.

VERSION 5 08.03.2023
USER GUIDE WINE OUT25X Page 18
6. WARRANTY
6.1.Legal warranty
The legal guarantee for defects and hidden defects applies according to the conditions of articles 1641 and
following of the civil code. The legal guarantee of conformity applies according to the conditions of article
L217-1 and following of the consumer code.
6.2. 2-years contractual warranty
The air conditioner is guaranteed for 2 years against any manufacturing defect.
During the contractual warranty period, WINEMASTER will replace any part recognized as defective.
In case of electrical failure, WINEMASTER will replace any part recognized as defective following the
intervention of the qualified retailer or his representative.
In case of refrigeration failure, WINEMASTER may request the return to the workshop for repair, following
the diagnosis made by the qualified dealer or his representative. The equipment will be kept packed at the
disposal of WINEMASTER's carrier for collection.
The interventions and returns will have to be carried out after written agreement of the
WINEMASTER after-sales service.
6.3.Conditions of application of the warranty
The contractual warranty applies to all devices installed and used in accordance with the "Installation and
Use Guide". Its application is conditioned by the presentation of the purchase invoice or its copy.
6.4.Exclusions and limits of the warranty
The warranty is denied in the following cases:
- Cellar insulation and installation have not been carried out in accordance with this guide.
- Damage is due to negligence, poor maintenance, faulty or inappropriate use of the WINEMASTER® (in
particular clogged filters).
- The exchange of parts or their repair under the warranty cannot have the effect of extending the warranty.
WINEMASTER can in no case be held responsible for the direct or indirect consequences related to the non-
functioning of the air conditioner. The warranty is limited to the product supplied by WINEMASTER.
As the European Community is dedicated to protecting the environment and
processing waste, it has put in place Directive 2002/96/EC on Waste from Electrical
and Electronic Equipment (WEEE).
In accordance with that standard, the presence of the logo with a crossed-out bin is
mandatory.
That logo means that the product may not in any event be disposed of with
household waste. It must be taken to an appropriate collection facility for the
treatment, repurposing and recycling of waste from electrical and electronic
equipment.
By doing so, you are doing your bit for the environment and helping to conserve
natural resources and protect human health.